Eagle power Speed Vac Leitfaden
Speed Vac
24” Battery
Vacuum Sweeper
OPERATION AND PARTS MANUAL
Rev. A 4/2002
GENERALNOTES
This guide has been edited for the CONSUMER according to directive CE897392 and its
ensuing amendments.
Carefully read the notes contained in this guide since they provide important directions
regarding the safety of assembling, use and maintenance.
Each machine, in accordance with directive CE897392 and its ensuing amendments, is identified
by a specific plate positioned on the frame and containing the following information.
• Manufacturer
• Model
• Manufacturing year
• Serial number
• Power supply voltage
• Working voltage
• Installed power
• Weight
Page 1
Description of Controls
12 3 4
• Filter-shaker push-button
• Main switch (Main broom)
• Side broom switch
• Centrifugal electric fan switch
CONDITION OF USE
CONSENTED USES
The 24” Battery Vacuum Sweeper is built for cleaning the ground in the following conditions of
employment:
a - Environments: *Both closed and opened.
b - Working surfaces: *Level surfaces enough compact and not much irregular as:
- Ceramics
- Wood
- Marble
- Concrete
- Asphalt
- Various plastic materials
- Carpets
c - Nature of the materials to remove:
*Dust
*Dirt in general
*Mould and rubble
*Not excessively heavy objects of considerable dimensions
NOT CONSENTED USES:
a - Environments: *In presence flammable materials
b - Working surfaces: *With gradients exceeding 2%
*Particularly irregular
*Particularly wet
c - Kind of materials: *Lighted cigarettes-end or any other material that could cause
combustion of debris inside the wast compartment.
*Toxic materials
*Oils
*Chemical materials
*Filiform materials
Page 2
CAUTION!!!!
Minimum working temperature -200C (-40F)
Maximum working temperature +400C (1040F)
Do not leave the unused machine exposed to UV
rays because they could damage the plastic
UNPACKING AND SETUP OF THE MACHINE
1- Remove the packing and make sure of the machine integrity.
2- Before using the machine proceed in this way:
2.1 Take from the Waste Hopper Table B-1
the Side Broom – Table A-20
2.2 Unscrew the screw and washers Table A-24 from the Gearmotor Table A-15.
Insert the broom on the gearmotor axle having the key slot matching the key, leaving the
spacer between the broom and the gearmotor, then fix it with the screw and washers
2.3 Remove the Cover Table A- 1 unscrewing the four screws that keep it fixed on the machine
frame.
2.4 Make sure that the input voltage of the Battery-charger corresponds to the input voltage
available.
The machine leaves the factory set for an input voltage of 120 VAC
For input voltages of 210/240 VAC :
Follow connections as per Table B – 5
2.5 Connect the battery terminals paying attention to the correspondence of polarities.
2.6 Provide for the charge of the battery (See the following directions PAGE 4 – Battery-
charger).
MACHINE SETUP
State of rest: the machine can be placed whether with the handle folded down or with the handle
in vertical position.
Page 3
Main broom
Operating the switch (Figure 1-2) the main broom Table C- 14 starts to work reaching
immediately the running speed. The lighting of a green LED signals the regular operation.
With the main broom working it is possible to operate:
Side broom
Operating the switch (Figure 1-3) the side broom will start working.
To adjust the side broom operate on the knob (Table A- 22).
Vacuum
Operating the switch (Figure 1-4) the centrifugal electric motor fan starts to work.
Electric filter-shaker
With the battery connected, the electric filter-shaker is always active.
- The operation takes place pressing the push-button (Figure 1- 1).
- With the machine in movement, before operating the filter-shaker, it is suggested to switch-off
the vacuum, switch (Figure 1- 4).
- With the machine still and the hopper out, switch-off the suction and the main broom switch
(Figure 1 - 2) , before operating the filter-shaker.
Battery
- The “discharged battery” limit is signalled by the lighting of a red Led and afterwards by the
motors switching off.
- To complete the work switch-off for a while the switch (Figure 1- 2).
- To make use of a further residual of charge, switch-off the side broom switch (Figure 1-
3).
CAUTION: In case of prolonged inactivity of the machine disconnect the battery terminals.
Battery charger
To charge the battery:
- Make sure that the transformer connections have been set for the suitable voltage from 90
up to 240 volts Figure 3 – Page 9.
- Use the cable already connected to the machine (Table A- 11), insert the plug in any suitable
AC. outlet.
- The time required for the complete recharge varies from 8 to 15 hours, depending on the power
grid condition.
- During the charge all functions are automatically switched-off.
CAUTION: during the battery charging avoid to have contacts
with parts of the circuit concerned by the network voltage.
Page 4
ORDINARYMAINTENANCE
Maintenance and replacement of the main broom:
a- Cleaning:
Check periodically, according to the use of the machine, the wear conditions of the main
broom Table C-14.To carry out this operation, the following tools are needed:
- Heavy-duty gloves.
- Breathing mask.
- Scissors
- Pliers
Switch off the machine. In order to see the main broom:
- Remove the waste container (Table B-1) and the battery (Table A- 9).
- Tilt the machine.
- Clean away from the broom any filaments or other.
b- Adjustment:
To adjust the distance of the main broom to the ground, operate the cam Table A-26 from
position 1 to position 5.
c- Replacement:
If the broom wear is such to require it, replace the broom :
- Release the driving belt Table A- 14.
- Disassemble the internal flap Table C- 13.
- Release the belt Table A- 14.
- Unscrew the eccentrics Table C- 1
- Remove the broom unit from its housing.
- Remove the two spacers Table C- 2 Table C- 3 .
- Remove the pulley-hub Table C- 5 and the free hub Table C- 6.
- Using a new broom, carry out the operations in reverse order.
Maintenance and replacement of the side broom:
With procedures and tools similar to the above mentioned ones.
a- Adjustment:
- Act on the knob Table A- 22
b- Replacement:
- Unscrew the fastening screw Table A- 24 and replace the broom (Table A- 20), paying
attention to the flat key that lock the broom to the gearmotor shaft.
Maintenance and replacement of the filter:
To carry out this procedure the following tools are needed:
- Heavy duty gloves.
- Breathing mask.
a- Cleaning / Replacement:
- Withdraw the split pin Table B- 11from the hole of the Pin Table B -11that hold the filter-
support (Table B- 10) at the machine frame.
- Remove the filter (Table B-12) and check the wear condition.
- If necessary, replace it.
- If not, proceed to clean it, beating it on the floor and, if possible, blow with compressed air
from the upper side at a distance of about 15 cm.
- Reassemble carrying out operations in reverse order.
Maintenance and replacement of the flaps:
- Periodically check the conditions of flaps’ rubbers.
a- Replacement of the front flap rubber:
- Unscrew the rod (Table C- 7).
- Unscrew the front strap iron (Table C- 9).
- Unscrew the straps iron (Table C- 8) -(Table C- 10).
- Replace the rubber (Table C- 13).
- Reassemble following the same operations in reverse order.
b- Replacement of the side flap’s rubber:
- Unscrew the bus-bar (Table C- 11).
- Replace the rubber (Table C- 14).
c- Replacement of the back flap’s rubber:
- Unscrew the back strap iron (Table C- 9).
- Replace the rubber (Table C- 12).
Page 6
Maintenance and replacement of the electronic circuit board:
In case of non-operation of some electrical components, check out the integrity of the fuses:
Figure 2 - F2
In case of a non good operation of the function of battery charging, check out the integrity of the
fuses:
Figure 2 - F1
Figure 3 - FUN
Figure 3 - FUR
If necessary, replace them with integral ones.
If this operation does not bring to the drawback elimination, turn to an authorized workshop.
Pag
Inhaltsverzeichnis
Andere Eagle power Staubsauger Handbücher
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
