Earth Way 2170T Tow Bedienungsanleitung

ASSEMBLY and OPERATING INSTRUCTIONS

for

EarthWay

EV-N-SPRED®

MODEL 2170T Tow

Broadcast Spreader

REV. 5-06

1. Remove and identify loose parts from carton.

2. Position hopper upside down and install frame using

(4) 1/4 – 20 x 1 1/2” Pan Head Phillips screws.

PAGE 1

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUES-

TIONS REGARDING THE SAFE OPERATION OF THIS SPREADER.

THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671 EMAIL: [email protected]

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

 If your spreader does not spread evenly, be sure the FRONT on the gear box points in the correct direction (toward the tow hitch).

The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller

plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.

 Your spreader is designed to be towed at three miles per hour, which is a brisk walking speed. Slower or faster speeds will change

the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.

 Clean your spreader thoroughly after each use. Wash between the shut off plate and bottom of the hopper.

 Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

 When using Rock Salt remove the agitator to prevent damage to the gearbox and remove salt from the hopper daily. Rock Salt will

reconstitute back into a solid block over night with humidity.

ROCK SALT OR POWDERED LIME

ARE NOT RECOMMENDED FOR USE

IN THIS SPREADER.

REMOVE AGITATOR WHEN USING

ICE MELT.

4. Install gear box by inserting the pinion shaft into hole in

center of hoppers bottom. The word “FRONT” on the gearbox

must point toward the hitch.

Follow label instructions on the hopper.

5. Install axle bearings to both lower handles.

NOTE: Notch on bearings and lower handles.

Bearings must go through flat side of lower handle.

3. Install impeller onto pinion shaft. Insert ⅛”x 1-1/4” cotter pin

through impeller then through pinion shaft. Use hole closest to the

gear box. Spread cotter pin to prevent from falling out. Next insert

cross brace (smaller diameter without the cross hole) thru the Gearbox

Brace.

NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT OVER TIGHTEN.

PAGE 2

6. Install lower handles onto axle to both sides as shown. Insert 2 ¼” bolt through second hole in lower handle and through first hole in

frame install locknut. DO NOT TIGHTEN. Now insert 1 ½” bolt through first hole in lower handle. Then through frame brace. NOTE:

Dimples on frame brace must be facing toward gear box as shown. Next into threaded connector in cross brace (smaller diameter without

the cross hole). DO NOT TIGHTEN.

Next insert 1 ½” bolt through other end of frame brace and through second hole in frame threaded connector in cross brace.

7. Slide axle bushing over axle and into axle

bearing to both sides as shown. 8. Install drive wheel to axle using pin hole nearest to lower handles as shown. Insert 2” cot-

ter pin through wheel and through axle. Bend with pliers to prevent pin from falling out.

TURN SPREADER UPRIGHT ON TO WHEEL.

10. Insert pivot rod into shut off plate as shown. (TIP: Make

sure the double bend end of the Pivot Rod is facing the Shut-off

plate) to the Turn to lock in place.

11. Insert other end of pivot rod into pivot and bracket

assembly as shown. Turn to lock in place.

12. Install control support between lower handles as shown

above inserting (2) 1 3/4” bolts thru Pivot Bracket and Lower

Handle, Control Support an other Lower Handle and secure with

1/4-20 lock nuts . Line up hole in cross brace with hole in control

support. Insert 1/4-20 x 2 1/4” bolt through control support and

through hole in cross brace. Apply 1/4-20 locknut. DO NOT

TIGHTEN LOCKNUT YET. TIGHTEN THIS NUT LAST.

PAGE 3

9. Install coast wheel to axle using outside pin hole. As shown, insert 1”

cotter pin through axle (not thru the wheel). Bend with pliers to prevent

pin from falling out.

13. Attach gauge and lever assembly to control support using (2) 1/4-20

x 1 1/2” bolts and (2) 1/4-20 locknuts. TIGHTEN NOW. Now tap with

hammer 1” hole plug into control support.

14. Install (1) 1/4-20 regu-

lar nut (not a locknut) on to

control rod as shown.

17. Pull lever back to setting “30” as shown. Next push pivot &

bracket forward so that the shut off plate in the hopper is in the full

open position. REMEMBER SETTING “30” ON THE FLOW

CONTROL LEVER MUST PLACE THE SHUT-OFF PLATE

IN THE FULL OPEN POSITION TO BE PROPERLY CALI-

BRATED. Now tighten the nuts against the pivot bracket to pre-

vent change in calibration.

18. Insert agitator to pinion shaft on inside of hopper. NOTE: the

position of flat side of the agitator. This pin should be in-

stalled as shown.

PAGE 4

15. Install the two 1/4-20 x 1” Stainless Steel bolts into holes lo-

cated on each side of the hopper and secure with 1/4-20 lock-nut.

Next slide Debris Screen under the two bolts inside the hopper. 16. Install flattened end of control rod in to lever on gauge as

shown. Turn to lock in place. Next push lever forward to setting

“0”. Align control rod with hole in pivot bracket, pull lever

backward to insert control rod through hole in pivot bracket.

Now install 1/4-20 regular nut on to control rod.

DO NOT TIGHTEN NUTS YET.

19. Tension on the flow control lever may be adjusted by

tightening or loosening the tension nut as shown.

WARRANTY

EARTHWAY guarantees this product to be free of defects in original workmanship and materials for a period of 90-days from sale to

the original user. If any defect develops during this period EARTHWAY will repair or replace this product at no charge provided the

defect is not the result of mishandling or tampering and that this product is received at the factory with shipping charges prepaid. For

quicker service you may call EARTHWAY at 574-848-7491 or write and describe the nature of the defect and we will send repair

parts to you. Due to the corrosive nature of most fertilizers and ice melters, EARTHWAY PRODUCTS, INC. makes no warranty or

guarantee against corrosion failure on models with plated steel or painted steel frames. Clean and dry your spreader thoroughly after

each use. Warranty covers parts only, not any labor charges to repair or replace those parts.

OPERATING INSTRUCTIONS

Before filling hopper, become familiar with the operation of this

spreader.

 Obtain proper setting for material to be used from the RATE

SETTING CHART included with this spreader.

 Move stop bolt on rate gauge assembly to the proper setting.

 While pushing spreader forward, pull control lever back to

stop bolt.

 To stop, push lever forward to close flow holes before you

stop moving.

 When finished, empty any remaining material from hopper.

 Thoroughly wash spreader and allow to dry before storing. No

oiling is necessary.

 Remove agitator when using Rock Salt to prevent damage to

the gearbox.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct from the

manufacturer, EARTHWAY PRODUCTS, INC. Be sure to

give the following information when ordering.

1. Model Number

2. Part Number

3. Part Description

Call (574) 848-7491 or 800-294-0671, or write for current prices.

PAGE 5

The settings furnished on the Rate Setting Chart are intended as

a guide only. Variations in physical characteristics of material

applied, walking/towing speed, and roughness of ground sur-

face may require slightly different spreader settings.

Due to the above conditions,

EARTHWAY PRODUCTS, INC. makes no warranty as to the

uniformity of coverage actually obtained from the settings

listed.

DONOT RETURN TODEALER FOR REPAIR

EARTHWAY PRODUCTS, INC.

1009 Maple Street

P.O. Box 547

Bristol, IN 46507

FOR YOUR RECORDS

Date Purchased

Store Name

EarthWay

Products, Inc.

P.O. Box 547

Bristol, Indiana 46507

(574) 848-7491

www.earthway.com

77051 Hitch Extension Kit

Key # Part # Description Key # Part # Description

1 40003 Screen 22 N/A 1/4-20 X 2-1/4" Bolt

2 60335 HopperAssembly, Includes Key #5& 24 23 25207 LowerHandle

3 N/A 1/4-20 X 1-1/2" PHPMS SS 24 12317 Shut Off Plate

4 33117 Agitator 25 22601 Upper Cross Brace w/Hole

5 12209 Hopper Bushing 26 25108 Frame

6 N/A 1/4-20 X 1" Bolt Stainless Steel 27 44249 Frame Brace

7 N/A 1/4-20 Nylon Insert Locknut 28 24704 Cross Brace

8 N/A 1/4-20 X 1-3/4" Bolt 29 12148 Axle Bearing

9 60300 Pivot & Bracket Assembly 30 12152 Axle Bushing

10 31138 #8 X 3/8" Type "A" Screw 31 12109 Impeller

11 44251 Pivot Rod 32 N/A 1/8" X 1-1/4" Cotter Pin

13 N/A 1/4-20 HexNut 34 60309 Gear Box & Axle Assembly

16 42263 Control Rod 35 36103 3/16" X 2" Cotter Pin Stainless Ste

17 60298 Gauge & Lever Assembly 36 70138 Drive Wheel/Coast Wheel

18 19113 1" Hole Plug 38 N/A 3/16" X 1" Cotter Pin

19 N/A 1/4-20 X 1-1/2" Bolt 40 77002 Optional Heavy Duty Rain Cover

20 44215 Hitch Plate 38145 Hardware Package

21 25603 Control Support 77051 Hitch Extension Kit

N/A - Available at most local hardware stores

Inhaltsverzeichnis

Andere Earth Way Streuer Handbücher

Earth Way

Earth Way EV-N-Spred C22HD Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way POLAR TECH 90365 Bedienungsanleitung

Earth Way

Earth Way M40 Bedienungsanleitung

Earth Way

Earth Way HIGH-OUTPUT 2040Pi-Plus Bedienungsanleitung

Earth Way

Earth Way Hand Crank Spreader Betriebsanleitung

Earth Way

Earth Way EV-N-SPRED 2150 Bedienungsanleitung

Earth Way

Earth Way Polar Tech 2040PI-PLUS Bedienungsanleitung

Earth Way

Earth Way 2100P Estate Bedienungsanleitung

Earth Way

Earth Way 2050 Bedienungsanleitung

Earth Way

Earth Way 2170-XL Bedienungsanleitung

Earth Way

Earth Way 2050TP Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way Prizelawn BF l Bedienungsanleitung

Earth Way

Earth Way Ev-N-SprEd 2030 Series Bedienungsanleitung

Earth Way

Earth Way 7350SU Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED C22HD Bedienungsanleitung

Earth Way

Earth Way FLEX-SELECT F80 Series Bedienungsanleitung

Earth Way

Earth Way M80ECM Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way POLAR TECH 90365 Montageanleitung

Earth Way

Earth Way EV-N-SPRED 2150 Bedienungsanleitung

Earth Way

Earth Way M20 Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung