Earth Way M20 Bedienungsanleitung

12Volt ATV

Broadcast Spreader

MODEL #M20 ASSEMBLY INSTRUCTIONS

Earthway_M20 Manual PAGE 1

M20 ELECTRIC SPREADERS



▪Always wear protective clothing, eye wear, and dust mask to prevent contact with chemicals and other materials

being applied with this machine.

▪Remove any material in the hopper before lifting or detaching this machine from the vehicle.

▪Care must be taken when lifting this machine so as not to cause personal injury or equipment damage. Never

attempt to install this machine to the vehicle alone. Recruit the help of someone to assist when attaching and

detaching this machine from the vehicle.

▪Refer to the material packaging or the Material Safety Data Sheet for precautionary measures required when

handling materials to be applied.

Before attaching this machine, consideration must be given to the load capacity of the vehicle. Refer to the owner’s

manual of the vehicle for rated load capacity. Be sure to take into account the weight of this machine is 20lbs. and the

weight of the material to be placed in the hopper when calculating the total load.

Thank you for

selecting EarthWay

for your spreader

needs. Our

production team in

Northern Indiana

takes pride in

building this

spreader. Our customer support team is

standing ready to ensure your success.

Please contact us at www.EarthWay.com

to see our full line of commercial, lawn &

garden tools.

Assembly and Operation Instructions

Earthway_M20 Manual PAGE 2

Assembly Instructions:

STEP 1: Unpack all parts from shipping carton to ensure no parts are missing. Refer to the exploded view.

STEP 2: Install the four (#9) 7/8” Tube plugs onto the ends of the two (#15) Frames with the help of a hammer or some

other tool.

STEP 3: Determine whether to mount on the front or the back of the luggage rack. Depending on whether the M20 is

mounted to the front or rear rack, you will need to install (#4) Control assembly to either the right (#11) or left (#15)

Frame tube to allow for use with the non-throttle hand. Wait until the unit is mounted to the Quad before installing the

Control.

STEP 4: Next install four 1/4-20 x 1-1/2” Carriage bolts (#12) through the Hopper assembly and then through ONE of

either side Frame and secure with 1/4-20 Hex Nut (#8).

STEP 5: Now position the M20 to the Quad and install the

remaining Frame member as outline above in STEP 4. Now

install the Control assembly (#4) to the Frame and secure with a

1/4-20 x 1-3/4” Carriage bolt (#13) and 1/4-20 Hex Nut (#8) and

tighten firmly to allow movement, but not allow the lever to

move unassisted.

Now install the M20 on your quad as outlined on the following

page.

WARNING

KEEP HANDS AWAY FROM ANY SPINNING OBJECT, SHUT-OFF PLATE, SHUT-OFF MECHANISM LINKAGE, AND THE

INSIDE OF THE HOPPER, EXTREME INJURY CAN OCCUR.

Assembly and Operation Instructions

Earthway_M20 Manual PAGE 3

HOW TO OPERATE SAFELY:

▪Read, understand, and follow all product label information provided on the material being applied.

▪An adjustable solid stop is provided that allows the operator to adjust to the desired opening position on the rate setting

control prior to operation of the vehicle. This allows repeatability to the stop without the need to look at the control

while operating the vehicle.

▪Establish the correct rate and then lock the stop in that position using the thumb wing nut on the setting control. 

OPERATING INSTRUCTIONS:

Before filling hopper, become familiar with the operation of this spreader. (Practice the following steps)

▪Turn the motor switch to the ON POSITION, so that the impeller is turning before going on to the next step.

▪While driving forward pull the lever back to the stop, this opens the shut off plate on the spreader.

▪To stop the flow of material, Push the lever to “0” or closed position, then turn the motor off when finished.

▪When finished empty any remaining material from hopper.

▪Thoroughly wash spreader and allow to dry before storing. A light coating of oil will help prevent corrosion of all metal

surfaces.

MOUNTING INSTRUCTIONS:

Position the M20 on the vehicle so that the impeller is positioned to be able

to spin clear of any part of the vehicle, this will allow a full 180 degree

spread pattern. Secure the frame to the mounting location with the

enclosed J-Bolts at positions that will secure the spreader so that it will not

move when operating the vehicle. For best results mount the spreader so

that the impeller is as close to the vehicle as possible, but clears any parts on

the vehicle and place the J-Bolts as shown below.

Connect the black wire (ground) to the negative (-) post on the battery and

the fused wire to the positive (+) post on the battery.

If for any reason the impeller rotates counter clockwise,

reverse the battery connection of the spreader. Correct

rotation is clockwise.

SPREADER CALIBRATION INSTRUCTIONS:

▪Loosen stop on the gauge and set to #30

▪Open the lever to #30 and make sure that the shut-off is fully open

▪Loosen the cable clamp on the bottom of the hopper and slide the outer cable IN/Out until the shut-off is fully

OPEN. Tighten the cable clamp and retest.

▪Calibration is now complete

▪TO CALCULATE THE SETTING:

▪Determine how much material is to be applied per 1,000 sq/ft.

▪Measure off a distance of 50 feet, preferably on a paved surface such as a parking lot.

▪Weigh out enough of the material to be applied to fill the hopper at least half full. Record the weight for future

use.

▪With the unit mounted on the vehicle and the hopper at least half full of the material to be spread, position the

vehicle far enough before the beginning of the 50 foot test area so that the vehicle will achieve the desired

speed before you reach the starting line.

Assembly and Operation Instructions

Earthway_M20 Manual PAGE 4

▪Set the rate setting stop at a position that you feel would be an appropriate setting.

▪Start the vehicle in motion and as you cross the starting line (of the 50 feet) move the rate lever to the open

position against the stop. Take care to be aware of what is going on around you maintaining control of the

vehicle.

▪Continue from the starting line with the unit spreading the material. As you cross the finish line move the rate

lever to the closed position.

▪Stop the vehicle and note the width of the spread path that was just completed.

▪Return to the start point and empty the remaining material from the hopper into your weighing container and

re-weigh.

All spare parts listed herein may be ordered direct from the manufacturer. Be sure to give the following information

when ordering.

1. Model Number

2. Part Number

3. Part Description

You can contact us by calling (574) 848-7491 to place an order with a credit card, or purchase online at

www.Earthway.com. Questions? Email us at [email protected]m

Assembly and Operation Instructions

Earthway_M20 Manual PAGE 5

M20 Parts List

Key #

Part #

Description Key # Part #

Description

77003

HEAVY DUTY RAIN COVER

43050

U-BOLT STRAP (M20)

77101

ELECTRIC MOTOR DRILLED (M20)

32103

1/4-20 NYLON INS LOCKNUT ZINC

60323

MOTOR SUPPORT ASSEMBLY (M20)

12318

LOWER HOUSING CLIP

60523

CONTROL ASSEMBLY-M20 REV907

12221

SHUT OFF PLATE

60322

HOPPER ASSEMBLY (M20)

31138

#8 X 3/8" PMT #8 HD COARSE BLACK

44287

"J" BOLT (M30/M20)

12109

IMPELLER (9" DIA)

60511

WIRE HARNESS ASSEMBLY (M20/M30)

34108

9/16" OD. X .257 ID. WASHER ZINC

32100

1/4-20 HEX NUT ZINC

12309

MOTOR BASE (M20/M21)

19132

7/8" TUBE PLUG

12310

MOTOR CAP (M20)

31103

#6 X 1/2" TYPE 25 HWHS ZINC

31101

1/4-20 X 3/4" HHMS ZINC

25118

FRAME (M20) REV 907 RIGHT

32106

10-24 WING NUT ZINC

37101

1/4-20 X 1 1/2" CARRIAGE BLT Z

12222

INDICATOR-BROADCAST

37108

1/4-20 X 1 3/4" CARRIAGE BOLT ZINC

60422

MOTOR ASSEMBLY (M20)

31124

#10 X 5/8" TYPE A PHPS ZINC

77032

STRAIN RELIEF (#1184) HEYCO

25119

FRAME (M20) REV 907 LEFT

Installation the 77122 3-Sided Deflector Kit requires drilling of the hopper and motor support assembly for fitting.

EC DECLARATION OF CONFORMITY

(Machinery Directive & Electromagnetic

Compatibility Directives)

Herewith we declare that the machinery described below is in accordance with the relevant

health and safety requirements of the EC Council Directives concerned with Machinery and Electromagnetic

Compatibility. No alterations are to be made to the machine without prior consultation and approval of Earthway

Products, Inc. otherwise the Declaration may become invalid. This equipment must be commissioned, used and

maintained strictly in accordance with the operating and maintenance instructions issued with the machine. Operators

must be trained in accordance with the recommendations given in the operating and maintenance instructions issued

with the machine.

Description of Machine: EarthWay®M20 12-volt Broadcast Spreader

Date of Supply: AS INVOICED DATE

Relevant EC Council Directives:

Machine Directives 89/392/EEC and subsequent amendments.

Assembly and Operation Instructions

Earthway_M20 Manual PAGE 6

Electromagnetic compatibility Directive 89/336/EEC and subsequent amendments.

DO NOT RETURN TO DEALER FOR REPAIR

CUSTOMER SERVICE

574.848.7491 | SUPPORT@EARTHWAY.COM | www.EARTHWAY.com | 1009 Maple Street, Bristol, IN 46507

ONE YEAR WARRANTY

EarthWay Products, Inc. warrants this product free of defects in original workmanship and materials for a period of one year to the

end user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. at its discretion

will repair or replace the part(s)/product at no charge provided the failure is not the result of incorrect installation, mishandling,

misuse, tampering, or normal wear and tear as determined by EarthWay.

EarthWay at its discretion may require that the part(s) or product be returned along with the original purchase receipt for

examination and compliance with the terms of this warranty. Do not return any product without first receiving authorization from

EarthWay Products, Inc.

To seek remedy under this warranty, contact EarthWay Products, Inc. at 574-848-7491, support@earthway.com or write to

EarthWay Products, Inc. 1009 Maple Street, Bristol, IN 46507 and describe the nature of the manufacturing defect. SPECIFIC

LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair or replacement of

non-conformances are specifically excluded. Due to the corrosive nature of most fertilizers and ice melt products, EarthWay

Products, Inc. makes no warranty against and specifically excludes part(s) or product degradation or failure due to corrosion or

its effects.

Inhaltsverzeichnis

Andere Earth Way Streuer Handbücher

Earth Way

Earth Way 2100P Estate Bedienungsanleitung

Earth Way

Earth Way 2600A-Plus Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way 2130 High-Output Bedienungsanleitung

Earth Way

Earth Way Ev-N-SprEd 2030 Series Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way 2050TP Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED 2150 Bedienungsanleitung

Earth Way

Earth Way 2600A-PLUS Bedienungsanleitung

Earth Way

Earth Way 2170T Tow Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED C24HD Bedienungsanleitung

Earth Way

Earth Way M21 Series Bedienungsanleitung

Earth Way

Earth Way PolarTech 90399 Montageanleitung

Earth Way

Earth Way 2050TP Bedienungsanleitung

Earth Way

Earth Way FLEX-SELECT F80 Series Bedienungsanleitung

Earth Way

Earth Way Prizelawn BF l Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED Bedienungsanleitung

Earth Way

Earth Way 2170-XL Bedienungsanleitung

Earth Way

Earth Way 2750 Bedienungsanleitung

Earth Way

Earth Way Polar Tech 90399 Bedienungsanleitung

Earth Way

Earth Way 2030 Bedienungsanleitung

Earth Way

Earth Way Polar Tech 90365 Bedienungsanleitung

Earth Way

Earth Way 2170T Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung