Earth Way 2170T Bedienungsanleitung
(Qty 4 #36214)
1/4-20 X 1-1/2”
Philips Panhead
(Qty 4 #36300)
1/4-20 SS Locknut
36210
Qty 2 36214
Qty 4
31100
Qty 7
31114
Qty 2
32103
Qty 8
31106
Qty 3
32100
Qty 2
33117
Qty 1
36105
Qty 1
33108
Qty 1
33109
Qty 1
36300
Qty 6
12152
Qty 2 12148
Qty 2
vvvvvvvv
vvvvvvvv
22
28
12 9
10
14
36
6
21
37
9
15
18
1. Remove and identify all loose parts from carton.
2. Position hopper on side. Install frame using (4) 1/4-20 x 1-1/2” Pan Head
Phillips machine screws and (4) 1/4-20 nylon insert locknuts. First put bolts
through holes in frame then through holes in bottom of hopper. Secure with
locknuts. TIGHTEN THESE LOCKNUTS NOW
DO NOT TIGHTEN WITH POWER TOOLS.
Pt# 52165 PAGE 1
2170T CommerCial Tow
BroadCasT spreader
ASSEMBLY and OPERATING INSTRUCTIONS Rev.1-10
EarthWay
EarthWay
EV-N-SPRED
EV-N-SPRED
®
®
GT
GT
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: TeChsupporT@earThway.Com
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
;If your spreader does not spread evenly, be sure the FRONT on the gear box points away from the tow bar of the spreader.
The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the
impeller plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
;Your spreader is designed to be pulled at three miles per hour, which is a brisk walking speed. Slower or faster speeds will
change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your spreader
thoroughly after each use. A coating of light spray oil will help prevent corrosion. Wash between the shut off plate and
bottom of the hopper.
;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
FRONT
Gearbox & Axle Assembly
Drive wheel side
Coast wheel side
Frame brace
1/4-20 x 1-1/2”
Hex Head Bolt
Step 6B & 6C
1/4-20 x 2-1/4”
Hex Head Bolt
Step 6A 1/4-20 Locknut
Impeller
Cross Brace
Dimples
Frame
Lower Handle
Pivot Rod
Shut-Off
1/4-20 x 1-1/2”
Pan Head Bolt
3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin through
impeller then through pinion shaft. Use hole closest to the gear box. Spread
cotter pin to prevent from falling out. Next, insert the Cross Brace into the
Gearbox Brace.
FR
O
NT
Pinion
Shaft
1/8 x 1-1/4”
Cotter Pin (#36105)
DRIVE WHEEL
HOLE
COAST WHEEL
HOLE
Impeller
Cross Brace
Gearbox & Axle Assembly
Gearbox Brace
Front
4. Install gear box by inserting the pinion shaft into hole in center of
hoppers bottom. The word “FRONT” on the gearbox must point to
Front of the hopper. Follow label instructions on hopper.
Axle Bearing
Flat
Side
Notch
5. Install axle bearings to both lower
handles. NOTE: Notch on bearings and
lower handles. Bearings must go through
at side of lower handle.
6. A - Install lower handles onto axle
to both sides as shown. Insert 2¼” bolt
through second hole in lower handle and
through rst hole in frame install locknut.
DO NOT TIGHTEN.
B - Now insert 1½” bolt through rst hole in lower handle. Then through frame brace. NOTE: Dimples on frame brace must be facing
toward gear box as shown. Next into threaded connector in cross brace. DO NOT TIGHTEN.
C - Next insert 1½” bolt through other end of frame brace and through second hole in frame install the second cross brace - this one has a
cross hole in the center of the tube.
NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT
OVER TIGHTEN.
PAGE 2
S
L
I
D
E
Gearbox
Axle Assembly
Lower
Handle
Frame
Brace
Cross Brace
7. Slide axle bushing over axle and into axle bearing to both sides as shown.
8. Install drive wheel to axle using pin hole nearest to lower handles as shown.
Insert 2” cotter pin through wheel and through axle. Bend with pliers to
prevent pin from falling out.
9. Install coast wheel to axle using outside pin hole. As shown, insert 1” cotter pin through axle (not thru the wheel). Bend with pliers to
prevent pin from falling out.
TURN SPREADER UPRIGHT ON TO WHEELS.
10. Insert pivot rod into shut off plate as shown. Turn to lock in place.
11. Insert other end of pivot rod into pivot and bracket assembly as shown. Turn to lock in place.
12. Install Control Support between lower handles as shown inserting (2) 1-3/4” bolts thru the Pivot Bracket and the Lower Handles and
secure with (2) lock nuts. Next, line up the hole in the Cross Brace with the hole in the Control Support. Insert 1-4-20 X 2-1/4” bolt
through the Control Support and thru the hole in the Cross Brace, secure with a 1/4-20 lock nut. Now determine if you want to add the
Hitch Extension to the Control Support and install the Hitch Plates with a 1/4-20 X 1-3/4” bolt and secure with a 1/4-20 lock nut.
13. Attach Gauge & Lever assembly to Control Support using (2) 1/4-20 X 1-1/2” bolts and (2) 1/4-20 lock nuts and TighTen
PAGE 3
1/4 X 2-1/4”
Hex Head Bolt
1/4 X 1-3/4”
Hex Head Bolt
1/4 - 20
Lock Nut
1/4 - 20
Lock Nut
1/4 - 20
Lock Nut
1/4 X 1-3/4”
Hex Head Bolt
Hitch Plates
Hitch Extension
1/4 X 1-1/2”
Hex Head Bolt
1/4 - 20
Lock Nut
5
1
0
1
5
3
0
Shut-Off
Plate
Pivot Rod
with extra bend
Rotate
Pivot
2” Cotter Pin
1” Cotter Pin
Gauge & Lever
Control Rod
Tabbed Hole
Control Rod
Lever Tension Nut
5
1
0
1
5
3
0
14. Install (1) 1/4-20 regular nut (not a locknut)
on to control rod as shown.
15. Install attened end of control rod in to lever on gauge as shown. Turn to lock in
place. Next push lever forward to setting “0”. Align control rod with hole in pivot
bracket, pull lever backward to insert control rod through hole in pivot bracket. Now
install 1/4-20 regular nut on to control rod.
16. Pull lever back to setting “30” as shown. Next push pivot & bracket forward
so that the shut off plate in the hopper is in the full open position. REMEMBER
SETTING “30” ON THE FLOW CONTROL LEVER MUST PLACE THE
SHUT-OFF PLATE IN THE FULL OPEN POSITION TO BE PROPERLY
CALIBRATED. Now tighten the nuts against the pivot bracket to prevent change in
calibration.
17. Tension on the ow control lever may be adjusted by tightening or loosening the
tension nut as shown.
1/4-20
Regular Nuts
Pivot
Bracket Control
Rod
18. Insert agitator to pinion shaft on inside of hopper.
Note: the position of at side of the agitator. This pin
should be installed as shown.
PAGE 4
1/4-20 x 1”
Hex Head Bolt
Stainless
1/4-20 Lock Nut
Stainless
19. Install debris screen into hopper, then insert
1/4-20 x 1” Stainless Steel Hex Bolt thru the hole in
the side wall of the hopper. Secure with Stainless
Steel lock nut - TIGHTEN WITH HAND TOOLS
ONLY
PAGE 5
The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of
material applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to the
above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings
listed.
5-YEAR LIMITED WARRANTY
EarthWay
Products, Inc. warrants this product to be free of defects in original workmanship and materials for a period
of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found,
EarthWay
Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of
incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by
EarthWay
.
EarthWay
at
its discretion may require that the part(s) or product be returned along with the original purchase receipt at owners’ expense for
examination and compliance with the terms of this warranty. (Do not return any product without rst receiving authorization
from
EarthWay
Products, Inc.). To seek remedy under this warranty, contact
EarthWay
Products, Inc. at 574-848-7491,
techsupport@earthway.com or write to (
EarthWay
Products, Inc. P.O. Box 547 Bristol, Indiana 46507) and describe the
nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor
charges associated with repair or replacement of non-conformances are specically excluded. Due to the corrosive nature of
most fertilizers and ice melt products,
EarthWay
Products, Inc. makes no warranty against and specically excludes part(s)
or product degradation or failure due to corrosion or its effects. Clean and dry your spreader thoroughly after each use, as a
preventative measure, coat all metal parts with a light oil or silicon spray.
HOW TO ORDER SPARE PARTS
All spare parts listed herein may be ordered direct from the
manufacturer. Be sure to give the following information when
ordering.
;Model Number
;Part Number
;Part Description
You can contact us by calling (574) 848-7491 or 800-294-0671
to place an order with a credit card.
Questions? parts@earthway.com
OPERATING INSTRUCTIONS
Before lling hopper, become familiar with the operation of this
spreader.
1. Obtain proper setting for material to be used from the RATE
SETTING CHART included with this spreader.
2. Move stop bolt on rate gauge assembly to the proper setting.
3. While pushing spreader forward, pull control lever back to
stop bolt.
4. To stop, push lever forward to close ow holes before you stop
moving.
5. When nished, empty any remaining material from hopper.
6. Thoroughly wash spreader and allow to dry before storing.
Light oiling can prevent corrosion.
Full Rate Path Half Rate Path
Start
Finish
Start
Finish
Key # Part # Description Key # Part # Description
1 40003 SQUARE SCREEN 21 60298 GAUGE & LEVER ASSEMBLY 2150/C24
2 60335 HOPPER ASSEMBLY 2170/2170T 22 42263 CONTROL ROD (2150T/2170T)
3 33117 AGITATOR 23 31138 #8 X 3/8" PMT #8 HD COARSE BLACK
4 12220 GEAR BOX BUSHING (2050) 24 36208 #6 X 3/8" TYPE 25 PHPS S.S.
5 12317 SHUT OFF PLATE (2600B) BLACK 25 32100 1/4-20 HEX NUT ZINC
6 44251 PIVOT ROD (2150/2170/C24) 26 36214 1/4-20 X 1 1/2" PHPMS S.S.
7 60300 PIVOT & BRACKET ASSEMBLY 2150/2170 27 36300 1/4-20 NYLON INSERT LOCKNUT S.S.
8 31114 1/4-20 X 1 3/4" HHCS ZINC 28 60309 GEAR BOX & AXLE ASS'Y C25SU/2170T
9 25207 LOWER HANDLE (2150's/2170's) 29 33109 3/16" X 2" COTTER PIN ZINC
10 22601 UPPER CROSS BRACE (2170T/C25) 30 70138 PNEUMATIC DRIVE WHEEL STUD (2150)
11 32103 1/4-20 NYLON INS LOCKNUT ZINC 31 36210 1/4-20 X 1" HHMS S.S.
12 25108 FRAME (2150T/2170T) 32 33108 3/16" X 1" COTTER PIN ZINC
13 31104 #14 X 1 1/2 TYPE 25 FHPS ZINC 33 12148 AXLE BEARING (2200/2100/2150)
14 25228 CROSS BRACE (2150/2170/S25) 11.25 REV908 34 12152 AXLE BUSHING (C2200/2150)
15 44249 FRAME BRACE (2150/2170) 35 19113 1.0" OD HOLE PLUG BLACK
16 31100 1/4-20 X 1 1/2 HHMS ZINC 36 44215 HITCH PLATE (PULL) (2170T)
17 31106 1/4-20 X 2 1/4" HHCS ZINC 37 25603 CONTROL SUPPORT (2150T/2170T)
18 12109 IMPELLER (9" DIA) (C-Series, 2150/2170) 38 60060R SIDE DEFLECTOR AND RAIN COVER (2170/C24)
19 36105 1/8" X 1 1/4" COTTER PIN S.S. 77002 HEAVY DUTY RAIN COVER 2170/C24 19"X19
20 11927 SHUTOFF SUPPORT- LARGE 60166R 3-SIDED SALT DEFLECTOR KIT
2170T Broadcast Tow Spreader ~ Parts List
vvvvvvvv
vvvvvvvv
Broadcast Spreader
26
27
27
31
27
2170T
31
5
4
11
11
11
9
21
16
17
16 15
16
12
20
24
9
16
14
15
16
17
18
23
37
6
36
7
8
2
22
1
38
16
30
29
28
33
34
32
19
11
25
25
10
3
17
35
77002
Heavy-Duty
Rain Cover
60166R #-Side Deector Kit
EarthWay
Products, Inc.
P.O. Box 547
Bristol, IN 46507
Phone: 800-294-0671
www.earthway.com
Inhaltsverzeichnis
Andere Earth Way Streuer Handbücher
Earth Way
Earth Way M40 Bedienungsanleitung
Earth Way
Earth Way 2600A-Plus Estate Bedienungsanleitung
Earth Way
Earth Way 2040Pi-Plus Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED C24HD Bedienungsanleitung
Earth Way
Earth Way 2050SU Bedienungsanleitung
Earth Way
Earth Way Prizelawn BF l Bedienungsanleitung
Earth Way
Earth Way 2050T Bedienungsanleitung
Earth Way
Earth Way 2130 Bedienungsanleitung
Earth Way
Earth Way 2600A-Plus Bedienungsanleitung
Earth Way
Earth Way 2050TP Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED 2150 Bedienungsanleitung
Earth Way
Earth Way 2050 Bedienungsanleitung
Earth Way
Earth Way 2170 Bedienungsanleitung
Earth Way
Earth Way 2170 Bedienungsanleitung
Earth Way
Earth Way 2600A-Plus Estate Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED Bedienungsanleitung
Earth Way
Earth Way POLAR TECH 90365 Montageanleitung
Earth Way
Earth Way Polar Tech 90399 Bedienungsanleitung
Earth Way
Earth Way FLEX-SELECT F80PSD Bedienungsanleitung
Earth Way
Earth Way EV-N-Spred C22HD Bedienungsanleitung
Beliebte Streuer Handbücher anderer Marken
Fisher
Fisher POLY-CASTER 78601 Bedienungsanleitung
TurfEx
TurfEx RS7200 Betriebsanleitung
Ferris
Ferris Pathfinder Series Bedienungsanleitung
Fayat Group
Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Installations- und Betriebshandbuch
EASTMAN
EASTMAN CR 500 Bedienungsanleitung
