Earth Way 2600A-Plus Estate Bedienungsanleitung
Frame
Upper handles
Gauge &
Linkage
Assembly
Handle Shaft
Lower
Handles
Wheels
Impeller
Gearbox
Axle
Control Rod
Frame Braces
1. Remove and identify all loose parts from carton.
#10 X 1-1/4”
Flat Head Screw
Pt# 52215 PAGE 1
EV-N-SPRED
EV-N-SPRED
EarthWay
EarthWay
®
®
2600A-Plus EstAtE
BroAdcAst sPrEAdEr
ASSEMBLY and OPERATING INSTRUCTIONS Rev. 3-10
HELPFUL HINTS: REVIEW THE DIRECTIONS BEFORE ASSEMBLY
;Make sure the ARROW on the gear box points to the front of the spreader. The impeller must turn clockwise. Reversing
the gearbox will cause the impeller to turn counter clockwise. Clean the impeller plate after each use. Fertilizer stuck on the
impeller blades will cause uneven spreading.
;Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your
spreader thoroughly after each use. A coating of light spray oil will help prevent corrosion. Wash between the shut off
plate and bottom of the hopper.
;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING
THE SAFE OPERATION OF THIS SPREADER, PLEASE CONTACT US. THIS MODEL INCLUDES LIFETIME TECHNICAL
SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, EmAil: tEchsuPPort@EArthwAy.com
2. Position hopper as shown to the right.
Install Frame using (4) #10 x 1¼” Flat
Head Phillips screws. TIGHTEN
THESE NOW
3. Install gear box by inserting the pinion shaft into hole in center of
hoppers bottom. The ARROW on the gearbox must point to FRONT of
the hopper. Follow label instructions on hopper.
F
R
O
N
T
Arrow
1/4 - 20 Lock-nut
1/4 - 20 x 1-1/2” Bolt
Handle Shaft
S
l
id
e
Right
Side Left
Side
Slide Axle Through as shown
1/4-20 x 2-1/4”
Bolt 1/4-20 x 2-1/4”
Bolt
Axle Bearing
Flat
Side
Notch
4. Install lower handles onto Frame and secure with ¼-20 x 2 ¼” bolt
through hole in Frame Braces and through the hole in frame install
locknut.
Next,Slidetheaxle(CoaStWheelSidefirSt) through the right
side lower handle and into the gearbox (with the arrow facing the
FRONT), you will need to rotate the axle to engage with the gearbox,
then through the left side lower handle.
TURN SPREADER UPRIGHT ON TO WHEELS.
PAGE 2
8. Install Handle Shaft as shown below using (2) 1/4-20 x
1½” Hex Bolt and (2) 1/4-20 Locknuts
5. Install the bearings over the axle and
press into the notches of the lower
handle as shown above.
Right
Side
DRIVE WHEEL
Left
Side
COAST WHEEL
Slide wheels on axle as shown
33106
1/8" X 3/4" Cotter Pin
33107
1/8" X 1-3/4" Cotter Pin
34103
1" OD. Washer
~~~IMPORTANT~~~
CoastDrive
Upper Handle
1/4 - 20 Lock-nut
1/4 - 20 x 1-1/2” Bolt
6. Install drive wheel to axle using pin hole nearest to lower handles
as shown. Insert 1¾” Cotter pin through wheel and through axle.
Bend with pliers to prevent pin from falling out.
7. Install coast wheel to axle using outside pin hole. As shown, add the
at washer, and insert ¾” Cotter pin through axle (not thru the wheel). Bend with pliers to prevent pin from falling out.
NOW GO BACK AND TIGHTEN ALL NUTS
AND BOLTS, DO NOT OVER TIGHTEN.
9. Insert (2) 1/4-20 x 1½” Hex Bolt
through Gauge and Linkage Assembly, then through the Upper Handle, Handle
Shaft, Upper Handle and secure with (2) 1/4-20 Locknuts as shown at the right.
PAGE 3
1/4 - 20 Locknut
1/4 - 20 x 1-1/2” Bolt
1/4 - 20 x 1-1/2” Bolt
1/4 - 20
Locknut
Gauge & Linkage Assembly
Control Lever
& Gauge
12. CALIBRATION: this stEP EnsurEs thAt your sPrEAdEr is ProPErly
AdjustEd to givE you A corrEct stArting Point to APPly mAtEriAls At thE corrEct
sEtting. Pull the Control Lever back to #30 on the Gauge, then push the shut-off plate
forward until the shut-off and the drop holes are fully open. Now tighten the Hex Nut on
the ½” Carriage Bolt on the Linkage Assembly. Check to conrm calibration by closing the
Control Lever, then reopening to #30 and conrm that the drop holes are fully open.
13. Insert agitator to pinion shaft on inside of hopper.
NOTE: Position of at side of the agitator as shown at the
right.
10. Attach Linkage Pivot with 1/4-20 x 1½” Hex Bolt, Flat
Washer, Spacer and Locknut as shown below. Next install
Control Rod into the Shut-Off Plate as shown at the right.
TIP: Make sure that the Control Rod is above the Lower
Handles.
60088
Gauge & Linkage
12147
Spacer
32103
1/4-20 Locknut
31100
1/4-20 X 1-1/2" Bolt
and 34108 Washer
41256
Control
Rod
36500
1/2” Carriage
Bolt
34100
Washer
32108
Hex Nut
60088
Linkage
12317
Shut-off
Plate
41256
Control
Rod
25304
Handle Shaft
12317
Shut-Off
Plate
60088
Linkage
32108
Hex Nut
34100
Washer
41256
Control
Rod
11. Using ½” Carriage Bolt, install through the Control Rod, Linkage and install the Flat
Washer and secure with Hex Nut to a loose t to allow for CALIBRATION below. See
above right and below for details.
PAGE 4
The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of
material applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to the
above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings
listed.
5-YEAR LIMITED WARRANTY
EarthWay
Products, Inc. warrants this product to be free of defects in original workmanship and materials for a period
of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found,
EarthWay
Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of
incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by
EarthWay
.
EarthWay
at its discretion may require that the part(s) or product be returned along with the original purchase receipt at owners’
expense for examination and compliance with the terms of this warranty. (Do not return any product without rst receiving
authorization from
EarthWay
Products, Inc.). To seek remedy under this warranty, contact
EarthWay
Products, Inc. at
574-848-7491, techsupport@earthway.com or write to (
EarthWay
Products, Inc. P.O. Box 547 Bristol, Indiana 46507)
and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or
product; any labor charges associated with repair or replacement of non-conformances are specically excluded. Due to
the corrosive nature of most fertilizers and ice melt products,
EarthWay
Products, Inc. makes no warranty against and
specically excludes part(s) or product degradation or failure due to corrosion or its effects. Clean and dry your spreader
thoroughly after each use, as a preventative measure, coat all metal parts with a light oil or silicon spray.
HOW TO ORDER SPARE PARTS
All spare parts listed herein may be ordered direct
from the manufacturer. Be sure to give the following
information when ordering.
;Model Number
;Part Number
;Part Description
You can contact us by calling (574) 848-7491 or
800-294-0671 to place an order using a credit card.
Questions? parts@earthway.com
OPERATING INSTRUCTIONS
Before lling hopper, become familiar with the operation of this spreader.
1. Obtain proper setting for material to be used from the RATE SETTING MATRIX included with this spreader.
2. Move stop bolt on rate gauge assembly to the proper setting for the material that you are spreading.
3. While pushing spreader forward, pull the Control Lever back to stop bolt.
4. To stop, push lever forward to close ow holes before you stop moving.
5. When nished, empty any remaining material from hopper.
6. Thoroughly wash spreader and allow to dry before storing. Spray all metal surfaces (inside & outside) with WD-40 or
other light oil to help prevent corrosion.
Full Rate Path Half Rate Path
Start
Finish
Start
Finish
6
16
19
22
20
23
16
19
8
11
3
21
18
7
12
15
5
77000
OPTIONAL
Heavy-Duty
Rain Cover
9
14
26
17
30
2
1
3
3
9
10
9
13
29
24
25
27
28
31
4
32
Drive Wheel
Side
Coast Wheel
Side
EarthWay
Products, Inc.
P.O. Box 547
Bristol, IN 46507
Phone: 800-294-0671
www.earthway.com
2600APlus Broadcast Spreader ~ Parts List
Key # Part # Description Key # Part # Description
1 19115 .875" ID. X 4" IL. BLACK GRIP 18 12128 LEFT FRAME BRACE
2 25403 UPPER HANDLE 19 31106 1/4-20 X 2 1/4" HHCS ZINC
3 32103 1/4-20 NYLON INS LOCKNUT ZINC 20 25107 FRAME
4 36500 #10-24 X 1/2" CARRIAGE BOLT SS 21 31138 #8 X 3/8" PMT #8 HD COARSE BLACK
5 33117 AGITATOR 22 12317 SHUT OFF PLATE
6 12251 HOPPER BUSHING 23 31108 #10 X 1 1/4" TYPE A FHPS ZINC
7 60089 HOPPER ASSEMBLY 24 12248 IMPELLER
8 60088 GAUGE & LINKAGE ASSEMBLY 25 60451 GEAR BOX ASSEMBLY
9 31100 1/4-20 X 1 1/2 HHMS ZINC 26 12167 SPLIT BEARING
10 34108 9/16" OD. X .257 ID. WASHER ZINC 27 12206 DUST COVER
11 12147 SPACER (PIVOT LINK) 28 33107 1/8" X 1 3/4" COTTER PIN SS
12 41256 CONTROL ROD 29 70149 9 IN PNEUMATIC WHEEL
13 34100 #10 FLAT WASHER SS 30 34103 1"OD X 17/32"ID X 1/32" WASHER ZINC
14 32108 10-24 HEX. NUT ZINC PLATED 31 33106 1/8" X 3/4" COTTER PIN ZINC
15 25304 HANDLE SHAFT 32 23519 AXLE
16 25210 LOWER HANDLE OPTIONAL 77000 HEAVY DUTY RAIN COVER 10.5”
17 12129 RIGHT FRAME BRACE
Inhaltsverzeichnis
Andere Earth Way Streuer Handbücher
Earth Way
Earth Way EV-N-SPRED Bedienungsanleitung
Earth Way
Earth Way Polar Tech 2040PI-PLUS Bedienungsanleitung
Earth Way
Earth Way 2030 Bedienungsanleitung
Earth Way
Earth Way FLEX-SELECT F80 Series Bedienungsanleitung
Earth Way
Earth Way POLAR TECH 90365 Montageanleitung
Earth Way
Earth Way M30 Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED 2150 Bedienungsanleitung
Earth Way
Earth Way FLEX-SELECT F80PSD Bedienungsanleitung
Earth Way
Earth Way 2050T Bedienungsanleitung
Earth Way
Earth Way M20 Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED C22HD Bedienungsanleitung
Earth Way
Earth Way 2100P Estate Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED C24HD Bedienungsanleitung
Earth Way
Earth Way EV-N-SPRED M20 Bedienungsanleitung
Earth Way
Earth Way 2600A-Plus Estate Bedienungsanleitung
Earth Way
Earth Way Polar Tech 90399 Bedienungsanleitung
Earth Way
Earth Way HIGH-OUTPUT 2040Pi-Plus Bedienungsanleitung
Earth Way
Earth Way 2130 High-Output Bedienungsanleitung
Earth Way
Earth Way 2600A-PLUS Bedienungsanleitung
Earth Way
Earth Way Polar Tech 90365 Bedienungsanleitung
Beliebte Streuer Handbücher anderer Marken
Fisher
Fisher POLY-CASTER 78601 Bedienungsanleitung
TurfEx
TurfEx RS7200 Betriebsanleitung
Ferris
Ferris Pathfinder Series Bedienungsanleitung
Fayat Group
Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Installations- und Betriebshandbuch
EASTMAN
EASTMAN CR 500 Bedienungsanleitung
