Eaton MPD-C-EXT Bedienungsanleitung
Overview
The MPD-C-EXT 12-24V microwave presence detector
switch is designed to provide automatic control of lighting,
heating or ventilation loads. It detects movement using a
highly sensitive microwave detector. This works by emitting
low power microwave signals and measuring the reflections
as the signals bounce of moving objects. The MPD-C-EXT
12-24V is optimised for ceiling mounting applications to
give detection over long distances.
When movement is detected the load is turned on. When
an area is no longer occupied the load will switch off after
an adjustable time out period.
The internal light sensor provides additional energy saving
in lighting applications. When an area is occupied lighting is
only switched on when the level of natural light is below a
preset level.
Features
Microwave Sensor
Detects movement within the unit’s detection range,
allowing load control in response to changes in occupancy.
IR Receiver
Receives control and programming commands from an IR
(infrared) handset.
Light Level Sensor
An integral adjustable photocell allows the lights to be kept
off if there is sufficient ambient light.
Presence detection
When movement is detected the load will automatically turn
on. When the area is no longer occupied the load will
automatically switch off after an adjustable time period.
Status LED
The LED flashes Red to indicate the following:
Fig 1: Front features
Walk Test LED active when movement is detected
Valid setting received
MPD-C-EXT 12-24V
Product Guide
Sensor Lens
which covers...
IR Receiver
Light Level Sensor
Status LED
2
To switch from more than one position simply wire two or more units in parallel to achieve two way and intermediate
switching.
The detector should be sited so that the occupants of the room fall inside the detection pattern shown overleaf, at a
recommended height of 2.8m for ceiling mounted sensors. Note that the higher the sensor is installed the shorter the
detection range will be.
Do not site within 1m of any lighting or ventilation equipment.
Do not fix to a vibrating surface.
Site as far away as possible from the surface of metal objects.
Ensure that all cable entry to the enclosure is via suitable cable glands and seal with silicone sealant where
appropriate.
If it is necessary to screw through the rear of the enclosure ensure that any holes are covered with the caps
provided and sealed with silicone sealant where appropriate.
Note: when externally mounted the unit may be triggered by trees, animals, leaves etc.
Wiring
-
+
NC
-
NC NO
COM
NO
+
Fault finding
What if the load does not turn ON?
Check to see if the live supply to the circuit is good.
If the supply and wiring are good, check the LUX level setting. Increase the LUX level setting to allow the
controller to turn on at higher ambient natural light level.
What if the load does not turn OFF?
Ensure that the area is left unoccupied for a greater time period than the time out period set using the switch.
Make sure that the sensor is not adjacent to vibrating surfaces or objects (e.g. ventilation equipment).
The unit may pick up movement through thin partitions or walls. Reduce the sensitivity.
3
Programming
Parameter
Name
Default
Value
0123HHIR-PROG Handset
Graphics
Description
Button Activation
On / Raise On Turn lights on.
Off / Lower Off Turn lights off.
Walk test Off On Off When set to On this causes a red LED to
flash on the sensor when it detects
movement. Use this feature to check for
adequate sensitivity levels.
Time Out
(Time
adjustment)
10 mins 1, 10 &
20
minutes
5, 15 &
30
minutes
Once the detector is turned on, this value
sets how long the lights will stay on once
movement has ceased.
Lux on level
(Switch
level on)
92, 5 & 7 4, 6 & 9 Lux level setting to prevent the luminaires
being switched on if the ambient light level
is sufficient (adjustable between 1
and 9). The luminaires will always be
switched on at level 9.
Lux off level
(Switch
level off)
92, 5 & 7 4, 6 & 9 Lux level setting to switch the luminaires off
during occupancy if the ambient light level
goes above the setting (adjustable between
1 and 9). Level 9 will always keep the lights
on. This setting can be used for “window
row switching”.
Sensitivity 91, 5 & 9 3, 6 & 8 Sensitivity level for detecting movement.
1 = low sensitivity
9 = high sensitivity
Defaults DReturns the unit to the default settings.
Shift Use this button to select the settings in red
and blue signified by the ‘Shift 1’ and ‘Shift
2’ LEDs
Number of Shift key presses
The functionality of the MPD-C-EXT 12-24V is controlled by a number of parameters which
can be changed or programmed by any of the following devices:
HHIR-PROG Infrared Handset. See below for programmable functions.
HHIR-LCD-PROG Infrared Handset (with LCD). See user guide for full
programming details.
For most basic programming operations the HHIR-PROG handset can be used and the
following procedures are based on using this device.
Point the handset at the Sensor and send the required programming commands to the unit
as shown below.
Valid commands will be indicated by a red LED flash. See page 1 for details of other LED
responses.
Note: other functions on the HHIR-PROG which are not shown below are not applicable to
this product.
SHIFT 1 SHIFT 2 SHIFT 1 SHIFT 2
SHIFT 1 SHIFT 2
SHIFT 1 SHIFT 2
4
The allowable frequency of operation of this product is different depending on region. Please select the correct order
code using the table below.
Frequency compatibility
Technical data
Detection pattern Dimensions
Supply Voltage Min 11.5VDC max 36VDC, min 10VAC
max 26.5VAC
Power consumption On 1.01W
Off - 712mW
Load Low voltage supply with relay
output rating 16A resistive 10A inductive
Weight 0.25kg
Terminal Capacity 2.5mm2
Time out period Adjustable 10 seconds to 99 minutes.
Light level Optional adjustment by using IR
programming handsets.
Fixing method Surface fixing by screws (not supplied) .
Temperature -10ºC to 35ºC
Humidity 5 to 95% non-condensing
Material (casing) Polystyrene Type Class 2
IP rating IP 66
Compliance EMC-2014/30/EU
LVD-2014/35/EU
Safety The microwave radiation emitted by these
units is extremely low power. At a distance
of > 50mm the power density is <6% of
the ANSI IEEE C95.1 –1991
recommended microwave power density.
At a distance of 5mm from the unit it is
<84% of recommended power density.
Due to our policy of continual product improvement we reserve the right to alter the specification of this product without prior notice.
Eaton Lighting Systems
Usk House, Lakeside
Llantarnam Park,
Cwmbran, NP44 3HD, UK
Tel: +44 (0)1633 838088
Fax: +44 (0)1633 867880
lightingcontrolsolu[email protected]m
www.eatonlightingsystems.com
Ref: 9850-000614-00
#WD861 Issue 3.0
IMPORTANT NOTICE!
This device should be installed by a qualified
electrician in accordance with the latest
edition of the IEE Wiring Regulations and
any applicable Building Regulations.
Code suffix Region Frequency
blank UK, China, India, Middle East, Malaysia, Hong Kong, Singapore 10.687GHz
-R2 Australia and all of Europe except:
UK, France, Portugal, Germany, Switzerland, Austria, Slovak Republic, Republic of
Ireland
10.525GHz
-R3 France, Portugal, Switzerland 9.900GHz
-R4 Germany, Austria, Slovak Republic 9.350GHz
-R5 Republic of Ireland 10.41GHz
Andere Eaton Zubehör Handbücher
Eaton
Eaton EX RT PDU Bedienungsanleitung
Eaton
Eaton xComfort Handbuch
Eaton
Eaton iProx Series Gebrauchsanweisung
Eaton
Eaton GridAdvisor II Series Bedienungsanleitung
Eaton
Eaton Cutler-Hammer iProx Series Gebrauchsanweisung
Eaton
Eaton xComfort CTEU-02/0 Series Bedienungsanleitung
Eaton
Eaton GridAdvisor II Series Bedienungsanleitung
Eaton
Eaton E67 Series Handbuch
Eaton
Eaton E65 SM Series Handbuch
Eaton
Eaton Cutler Hammer CurrentWatch EGF Series Bedienungsanleitung
Eaton
Eaton Powerware Series Bedienungsanleitung
Eaton
Eaton EAFR-01 Bedienungsanleitung
Eaton
Eaton Metalux WaveLinx Bedienungsanleitung
Eaton
Eaton E67 Series Handbuch
Eaton
Eaton Home Heartbeat Bedienungsanleitung
Eaton
Eaton CurrentWatch EDC Series Handbuch
Eaton
Eaton E55 Series Handbuch
Eaton
Eaton CurrentWatch EPRM Series Bedienungsanleitung
Eaton
Eaton CurrentWatch EDC Series Handbuch
Eaton
Eaton xComfort CSEZ-01/14 Kurzanleitung
