Eaton Network Card-MS Programmierhandbuch

Eaton®Network Card-MS

Quick Start Instructions

Package Contents

lNetwork Card-MS

lUSB Cable

lQuick Start Instructions

ACT 100M

MAC:

ETHERNET

Settings/Sensor

RS232UPS Data

Help Desk Numbers

United States 1-800-356-5737 or 1-800-843-9433

Canada 1-800-461-9166 ext 260

All Other Countries Call your local service representative

Eaton, PredictPulse, and Power Xpert are registered trademarks of Eaton

Corporation or its subsidiaries and affiliates. Google Chrome is a trademark of

Google Inc. Linux is a registered trademark of Linus Torvalds. Microsoft, Internet

Explorer, and Windows are registered trademarks of Microsoft Corporation in the

United States and in other countries. Mozilla and Firefox are registered

trademarks of the Mozilla Foundation. All other trademarks are property of their

respective companies.

part of this document may be reproduced in any way without the express written

approval of Eaton Corporation.

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 3

TABLE OF CONTENTS

Section 1 Installation Checklist ........................................................................ 4

Section 2 Install the Card ................................................................................. 5

Section 3 Connect the Card to the Computer .................................................. 6

Section 4 Initialize the Card Configuration ...................................................... 7

Section 5 Obtain a DHCP-assigned IP Address ............................................. 10

Section 6 Assign an IP Address Manually ..................................................... 14

Section 7 Disable Browser Compatibility Mode ............................................ 18

Section 8 Register a PredictPulse Subscription ............................................. 19

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 4

Section 1 Installation Checklist

1. Verify that the following items are available:

oNetwork Card-MS card package contents (card, cable, Quick Start

Instructions)

oPhillips®screwdriver

oAvailable USB port on a computer running Microsoft®Windows®

oWeb browser (Microsoft Internet Explorer® version 8.0 and higher,

Mozilla®Firefox®, or Google Chrome™ are recommended)

2. If you are going to use Dynamic Host Configuration Protocol (DHCP), provide

your local network administrator with the card's MAC address. The MAC

address is located on either the shipping box label or the label on this card.

oMAC Address _____________________________________________

3. If you are not going to use DHCP to provide any of the settings listed below,

contact your local network administrator for the settings.

In the table below, check the DHCP check box or enter the values for manual

configuration.You will reference this data later in the procedure.

4. If you need e-mail functionality, obtain the SMTP mail server's IP address or

host name. If using the SMTP host name, verify that you also have the

Name Server IP address (see Step 3).

oSMTP (mail server) IP Address

or Host Name _____________________________________________

Item DHCP* Manual Configuration

IPv4 oCard IP Address: ________________________

Netmask: ________________________

Gateway: ________________________

DNS – Name Servers oName Server #1: ________________________

Name Server #2: ________________________

Name Server #3: ________________________

DNS – Domain oDomain: ________________________

* The network administrator normally sets up the DHCP server to provide a static IP address each time

the card makes a DHCP request.

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 5

Section 2 Install the Card

Note: The hot-swappable Network Card-MS card can be installed without

turning off the UPS or disconnecting the load.

To install the Network Card-MS card:

1. Remove the minislot cover from the UPS. Retain the screws.

2. If not already done, record the card’s MAC address from the label on the

card for future reference (see Step 2 in the “Installation Checklist”).

Note: If another card is already installed with an attached communication

cable, disconnect the cable and then remove the card.

3. To prevent electrostatic discharge (ESD), place one hand on a metal surface,

such as the UPS rear panel.

4. Slide the card into the open slot and secure it with the screws removed in

Step 1 (see Figure 1).

Figure 1. Installing the Card

ACT 100M

MAC:

ETHERNET Settings/Sensor

RS232UPS Data

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 6

Section 3 Connect the Card to the Computer

Note: You can set the card parameters through the Settings/Sensor port even

if the network is not connected.

Note: You cannot use the Ethernet port for configuration.

Note: When the card is not connected to the network, it continuously

attempts to connect. When the connection is established, the LEDs

indicate the status.

To connect the card to the computer and the network:

1. Verify that the UPS is on and in normal mode.

Note: If you are not sure how to know if the UPS is in normal mode, refer to

the User’s Guide for your UPS.

2. Plug the RJ-45 end of the supplied configuration cable into the

Settings/Sensor port on the card (see Figure 2).

3. Plug the other end of the serial cable into the serial COM port on the

computer. (Depending on your laptop, you may need an adapter for this

step.)

4. Connect an active Ethernet cable (not supplied) from the network

connection to the Ethernet port on the Network Card-MS (see Figure 2).

Figure 2. Connecting the Card

5. Wait approximately two minutes until the green UPS Data LED flashes

regularly, indicating normal operation.

ACT 100M

MAC:

ETHERNET

Settings/Sensor

RS232UPS Data

Ethernet Cable Conguration Cable

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 7

Section 4 Initialize the Card Configuration

Note: These instructions are for HyperTerminal, but you can use the terminal

emulation program of your choice, such as HyperTerminal or PuTTY.

Note: Before you start initializing the card configuration, you will need to know

which COM port you are using on your computer.

To initialize the card configuration:

1. Verify that the serial cable (supplied) connects the card’s Settings/Sensor

port to the computer’s COM port. Also verify that the UPS is on and in

normal mode.

2. Click Start in the computer Start bar. Type Device in the search box. Select

Device Manager in the list above the search box. The Device Manager

opens.

3. Locate Ports (COM & LPT) in the list and click the adjacent “plus box” to

expand the selection. Make a note of the COM port you are using.

4. Open HyperTerminal.

5. Respond Ye s or No to the message asking if you want to make

HyperTerminal your default terminal emulation program.

6. Optional. When the Connection Description dialog box opens, enter a name

for this connection and click OK. Otherwise, click Cancel.

7. In the New Connection Window, make the menu selection

File > Properties. On the screen that displays, select New Connection

Properties.

8. From the “Connect Using...”drop-down list, select the COM port that you

are using (see Figure 3).

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 8

Figure 3. Selecting the COM Port

9. Click Configure.

10. In the COM Properties dialog, click Restore Defaults to set the correct baud

rate, data bits, stop bit, and flow control.

11. C l i ck OK.

12. At the blinking screen, press Enter. You should be prompted enter the

password (default is admin).

Note: If the Password prompt does not appear, press Enter again. If it still

does not appear, check the following conditions:

lVerify the serial line is set to 9600 baud, no parity, 8 data bits, 1 stop bit,

and no flow control.

lIf the serial line settings are correct, check the cabling to verify all

connections are secure.

lVerify that your terminal program is set to the correct communication port

for the serial connection.

lVerify that the card has power (one or more LEDs on the card are

illuminated). The UPS should be turned on.

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 9

13. Enter the password (default is admin). The Network Card-MS main menu

displays (see Figure 4).

Figure 4. Network Card-MS Main Menu

14. Determine the IP address for the card. Either obtain a DHCP-assigned IP

address or manually enter a fixed IP address:

lTo obtain the IP address assigned through DHCP, continue to "Obtain a

DHCP-assigned IP Address" on page 10.

lTo manually enter a static (fixed) IP address for the card’s network

connection, continue to "Assign an IP Address Manually" on page 14.

Eaton Network Card-MS Quick Start Instructions P-164000507—Rev 1 10

Section 5 Obtain a DHCP-assigned IP Address

1. From the Network Card-MS main menu, type 2 for Network Configuration.

The Network Settings menu displays.

2. Type 1for Read Network Settings. At the cursor prompt, enter Y for “yes,” in

order to use DHCP to obtain an IP address from the network (see Figure 5).

Figure 5. Select Yes for DHCP

Andere Handbücher für Network Card-MS

Inhaltsverzeichnis

Andere Eaton Messgerät Handbücher

Eaton

Eaton 5775X-42X Bedienungsanleitung

Eaton

Eaton GIM 60 Bedienungsanleitung

Eaton

Eaton PXG 900 Bedienungsanleitung

Eaton

Eaton CMD Bedienungsanleitung

Eaton

Eaton IQ 200 Bedienungsanleitung

Eaton

Eaton Power Xpert Meter 2000 Bedienungsanleitung

Eaton

Eaton Cutler-Hammer IQ 300 Series Programmierhandbuch

Eaton

Eaton SONiX Pm10 Bedienungsanleitung

Eaton

Eaton CMD Handbuch

Eaton

Eaton RMD Bedienungsanleitung

Eaton

Eaton Cutler-Hammer Handbuch

Eaton

Eaton Crouse-Hinds Z130 Bedienungsanleitung

Eaton

Eaton 1MM Bedienungsanleitung

Eaton

Eaton Moeller Series Bedienungsanleitung

Eaton

Eaton MEMSHIELD3 Handbuch

Eaton

Eaton K1650 Bedienungsanleitung

Eaton

Eaton IQ 35M Series Bedienungsanleitung

Eaton

Eaton PXBCM-MB Handbuch

Eaton

Eaton Power Xpert Meter 4000 Bedienungsanleitung

Eaton

Eaton IQ 100 series Leitfaden

Eaton

Eaton Power Xpert C445 Handbuch

Eaton

Eaton PXM4K Series Bedienungsanleitung

Eaton

Eaton EMV600 Bedienungsanleitung

Eaton

Eaton Durant Eclipse 5775X-40 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung