Eaton DX RT 6K UPS Bedienungsanleitung

Eaton DX RT Online UPS

6000/10000VA(XL) IN USER MANUAL

Service and support

Call your local service representative

Safety Instructions

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be

followed during installation and maintenance of the UPS and batteries.

The UPS models that are covered in this manual are intended for installation in an environment

within 0 to 50°C, free of conductive contaminant.

Certification standards

•

Safety: EN 62040-1

•

EMC: IEC/EN 62040-2

•

IEC 61000-4-2 (ESD): level 3.

•

IEC 61000-4-3 (Radiated field): level 3.

•

IEC 61000-4-4 (EFT): level 4.

•

IEC 61000-4-5 (Fast transients): level 4.

•

IEC 61000-4-6 (Electromagnetic field): level 3.

•

IEC 61000-4-8 (Conducted magnetic field): level 4.

•

Performance: IEC/EN 62040-3

Special symbols

The following are examples of symbols used on the UPS or accessories to alert you to

important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of

electric shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.

This product contains sealed lead acid batteries and must be disposed as it's explain

in this manual. For more information, contact your local recycling/reuse or hazardous

waste center.

This symbol indicates that you should not discard waste electrical or electronic

equipment (WEEE) in the trash. For proper disposal, contact your local

recycling/reuse or hazardous waste center.

Information, advice, help.

Refer to the user manual.

Safety of persons

 RISK OF VOLTAGE BACKFEED. The system has its own power source (the battery).

Isolate the UPS and check for hazardous voltage upstream and downstream during

lockout-tagout operation. Terminal blocks may be energized even if the system is

disconnected from the AC power source.

 Dangerous voltage levels are present within the system. It should be opened exclusively by

qualified service personnel.

 The system must be properly grounded.

 The battery supplied with the system contains small amounts of toxic materials. To avoid

accidents, the directives listed below must be observed:

- Servicing of batteries should be performed or supervised by personnel knowledgeable

about batteries and the required precautions.

- When replacing batteries, replace with the same type and number of batteries or battery

packs.

- Do not dispose of batteries in a fire. The batteries may explode.

- Batteries constitute a danger (electrical shock, burns). The short-circuit current may be

very high.

 Precautions must be taken for all handling:

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect charging source prior to connecting or disconnecting battery terminals.

- Determine if battery is inadvertently grounded. If inadvertently grounded, remove source

from ground. Contact with any part of a grounded battery can result in electrical shock.

The likelihood of such shock can be reduced if such grounds are removed during

installation and maintenance (applicable to equipment and remote battery supplies not

having a grounded supply circuit).

Product safety

 The UPS connection instructions and operation described in the manual must be followed

in the indicated order.

 CAUTION - To reduce the risk of fire, the unit connects only to a circuit provided with

branch circuit overcurrent protection for :

63A rating, for 6kVA models,

100A rating, for 10kVA models

 The upstream circuit breaker for Normal AC/Bypass AC must be easily accessible. The unit

can be disconnected from AC power source by opening this circuit breaker.

 An additional AC contactor is used for backfeed protection and must comply with IEC/EN

62040-1 (the creep age and clearance distances shall meet the basic insulation

requirements for pollution degree 2).

 Disconnection and overcurrent protection devices shall be provided by others for

permanently connected AC input (Normal AC/Bypass AC) and AC output circuits.

 Check that the indications on the rating plate correspond to your AC powered system and

to the actual electrical consumption of all the equipment to be connected to the system.

 For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment

and shall be easily accessible

 Never install the system near liquids or in an excessively damp environment.

 Never let a foreign body penetrate inside the system.

 Never block the ventilation grates of the system.

 Never expose the system to direct sunlight or source of heat.

 If the system must be stored prior to installation, storage must be in a dry place.

 The admissible storage temperature range is -25°C to +60°C with battery(-15°C to +40°C

without battery).

Special precautions

 The unit is heavy: wear safety shoes and use vacuum lifter preferentially for handling

operations.

 All handling operations will require at least two people (unpacking, lifting, installation in rack

system).

 Straps are provided only for unpacking manually the unit from the carton; don’t use the

straps to carry the unit around. The unit can slip from the straps during handling (risk of

injury and product damage):

- keep 12in / 30cm minimum distance between the straps

- lift the unit carefully and keep it at low height

- keep the unit horizontal during unpacking.

 Before and after the installation, if the UPS remains de-energized for a long period, the

UPS must be energized for a period of 24 hours, at least once every 6 months (for a normal

storage temperature less than 25°C). This charges the battery, thus avoiding possible

irreversible damage.

 During the replacement of the Battery Module, it is imperative to use the same type and

number of element as the original Battery Module provided with the UPS to maintain an

identical level of performance and safety.

Contents

1. Introduction ...................................................................................................... 1

1.1 Environmental protection.......................................................................................................... 1

1.2 Electronic equipment protection .............................................................................................. 2

2. Presentation ...................................................................................................... 3

2.1 RT Front panel ........................................................................................................................... 3

2.2 RT Rear panels .......................................................................................................................... 3

2.3 EBM Front panel: ...................................................................................................................... 4

2.4 EBM rear panel: ......................................................................................................................... 4

2.3 Circuit diagram........................................................................................................................... 4

3. Installation ........................................................................................................ 5

3.1 Inspecting the equipment ......................................................................................................... 5

3.2 Unpacking the Unit .................................................................................................................... 5

3.3 Checking the accessory kit ...................................................................................................... 6

3.4 Install the unit ............................................................................................................................. 7

4. Power cables connection .................................................................................. 10

4.1 Access to terminal blocks (AC source to UPS) ................................................................... 11

4.2 Access to terminal blocks (PDU source to R/T UPS)(Optional) ........................................ 12

4.3 Parallel Installation and Operation (Optional) ...................................................................... 12

5. Operation ........................................................................................................ 17

5.1 Control panel ............................................................................................................................ 17

5.2 LCD description ....................................................................................................................... 19

5.3 Display functions ..................................................................................................................... 21

5.4 User settings ............................................................................................................................ 22

5.5 UPS startup and shutdown .................................................................................................... 23

5.6 LCD operation .......................................................................................................................... 25

6. Communication ............................................................................................... 33

6.1 Communication ports .............................................................................................................. 33

6.2 Intelligent Card (Optional) ...................................................................................................... 34

6.3 UPS Management Software .................................................................................................. 34

7. UPS maintenance ............................................................................................ 35

7.1Equipment care......................................................................................................................... 35

7.2 Transporting the UPS ............................................................................................................. 35

7.3 Storing the equipment............................................................................................................. 35

7.4 Replacing batteries ................................................................................................................. 36

7.5 Recycling the used equipment .............................................................................................. 37

8. Troubleshooting .............................................................................................. 38

8.1 Typical alarms and faults ........................................................................................................ 38

8.2 Silencing the alarm .................................................................................................................. 42

9. Specifications ................................................................................................. 43

9.1 Model specifications ................................................................................................................ 43

10 Glossary ........................................................................................................ 47

1. Introduction

Thank you for selecting UPS to protect your electrical equipment. The UPS has

been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage

of the many features of your UPS (Uninterruptible Power System).

Before installing your UPS, please read the booklet presenting the safety

instructions. Then follow the indications in this manual.

1.1 Environmental protection

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing

components.

•

The cardboard we use comprises over 50% of recycled cardboard.

•

Sacks and bags are made of polyethylene.

•

Packing materials are recyclable and bear the appropriate identification

symbol

Materials

Abbreviations

Number in

the symbols

Polyethylene terephthalat

PET

High-density polyethylene

HDPE 02

Polyvinyl chloride

PVC 03

Low-density polyethylene

LDPE 04

Polypropylene

PP 05

Polystyrene

PS 06

Follow all local regulations for the disposal of packing materials.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local

regulations concerning waste. At the end of its service life, the product must be

transported to a processing center for electrical and electronic waste.

Battery

The product contains lead-acid batteries that must be processed according to

applicable local regulations concerning batteries.

The battery may be removed to comply with regulations and in view of correct

disposal.

1.2 Electronic equipment protection

The uninterruptible power system (UPS) protects your sensitive electronic

equipment from the most common power problems, including power failures,

power sags, power surges, brownouts, line noise, high voltage spikes, frequency

variations, switching transients, and harmonic distortion.

Power outages may occur unexpected, and the power quality will be erratic.

These power problems have the potential to corrupt critical data, destroy

unsaved work sessions, and damage hardware - causing hours of lost

productivity and expensive repairs.

With the UPS, you can safely eliminate the effects of power disturbances and

guard the integrity of your equipment. Providing outstanding performance and

reliability, UPS’s unique benefits include:

 True online double-conversion technology with high power density, utility

frequency independence, and generator compatibility.

 Selectable High Efficiency mode of operation.

 Standard communication options: one RS232 communication port, one USB

communication port, one dry in port and dry out port.

 Optional connectivity cards with enhanced communication capabilities.

 Firmware that is easily upgradable without a service call.

2. Presentation

2.1 RT Front panel

2.2 RT Rear panels

1. Intelligent slot

2. USB

3. RS232

4. RJ11 (only for RT model)

5. EPO

6. Parallel card (optional)

7. Dry IN/OUT

8. Input /Output terminal

(Standard model 5pole, IPL, IPN, PE,OPL,

OPN; long backup model has 2 version, one

is 5 Pole. Another is 7pole. 7pole add bat+,

bat-, and no external battery connector #10.)

9. Input switch

10. External battery connector

11. Maintenance bypass switch

(optional)

12. EBM connector

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton 9E10000i Bedienungsanleitung

Eaton

Eaton Power Xpert 9395P-1200 Bedienungsanleitung

Eaton

Eaton Callisto 5PX RT G2 Bedienungsanleitung

Eaton

Eaton UPS 20 Bedienungsanleitung

Eaton

Eaton 3SMini Bedienungsanleitung

Eaton

Eaton SU700XLCD Bedienungsanleitung

Eaton

Eaton Ellipse ECO 500 Bedienungsanleitung

Eaton

Eaton 9355-F47 Unirom Bedienungsanleitung

Eaton

Eaton 9315 Bedienungsanleitung

Eaton

Eaton Powerware 5125 Bedienungsanleitung

Eaton

Eaton Powerware 9355 Parallel Bedienungsanleitung

Eaton

Eaton 3SMini Montageanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton DXRT 10KS31-IN Series Bedienungsanleitung

Eaton

Eaton Powerware BladeUPS Bar Bedienungsanleitung

Eaton

Eaton DX 10000LXL Bedienungsanleitung

Eaton

Eaton BladeUPS none Bedienungsanleitung

Eaton

Eaton Powerware 9355 Bedienungsanleitung

Eaton

Eaton Eaton 5PX Bedienungsanleitung

Eaton

Eaton Powerware 3105 UPS Bedienungsanleitung

Eaton

Eaton 5E Montageanleitung

Eaton

Eaton 350 VA Bedienungsanleitung

Eaton

Eaton EX 2200 RT 2U Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung