Eccotemp L10 Bedienungsanleitung

Functions and Features

Functions and FeaturesFunctions and Features

Functions and Features

• Water controlled automatic ignition: Water pressure

between 20-80 PSI opens the ignition circuit for easy and

convenient operation

• uto-cut-off protection: The auto-cut-off protection will

shut the gas supply off immediately in the event of

flameout to reduce the risk of gas leakage. There is also

an automatic shut-off timer after 20 minutes of continuous

use

• Energy savings: EF of 85%

• Removable drain valve to avoid water pipe and regulator

damage caused by freezing water*

• nti-dry combustion protection: The unit will shut off the

gas supply in the event water stops flowing through the

unit

*Read the maintenance section on draining the unit

entirely to avoid freeze issues.

EccoTemp Systems, LLC

EccoTemp Systems, LLCEccoTemp Systems, LLC

EccoTemp Systems, LLC

Volume 1, Issue

Volume 1, Issue Volume 1, Issue

Volume 1, Issue 2

THE FUTURE OF EFFICIE CY

10 LITER OUTDOOR MOU T LIQUID PROPA E WATER HEATER

L-

-10 Liter

10 Liter10 Liter

10 Liter

Outdoor

OutdoorOutdoor

Outdoor

Tankless Water Heater

Tankless Water HeaterTankless Water Heater

Tankless Water Heater

Table of

Table ofTable of

Table of

Contents

ContentsContents

Contents

Use and Care Introduction ............................................................ 3

W RNINGS ................................................................................... 4

The Purpose and Benefits of the L10 ............................................ 7

Functions and Features................................................................. 8

Getting Started ............................................................................ 10

Installation/Use ............................................................................ 12

djustment……………………………………………………………..1

Troubleshooting……………………………………………………... 16

dditional Products ..................................................................... 20

The Purpose and Benefits the L

The Purpose and Benefits the LThe Purpose and Benefits the L

The Purpose and Benefits the L-

-10

1010

The EccoTemp L-10 is a liquid propane fired water heater capable

of delivering 2 to 2.65 gallons of hot water almost anywhere. The

unit has standard 1/2“NPT pipe fittings and an adapter for using a

standard garden hose for inlet water supply.

The L-10 is not a toy. People around the world use similar units to

heat the water in their homes, safely, and reliably.

Gas is supplied from a standard 20 pound propane cylinder (not

included) such as used with outdoor grills. regulator with hose is

furnished with the heater.

You may also plumb it in to existing water lines and using a low

pressure LP gas regulator.. Check local codes for proper

installation.

The unit includes a stainless steel rain cap that is to help venting

of the flue gases as well as protect it for outdoor usage.

Ignition is automatic and powered by 2 “D” cell batteries (not

included). Burners come on when water flows, and off when the

water is shut off. No pilot light!

ADDITIONAL WARNIN S

1. Do not leave unattended

2. The exhaust gas and top of the

unit is HOT! Do not place hands

or any foreign object near the top

of the heater.

3. Do not use in high wind

conditions

4. If the smell of gas is detected,

turn off the gas valve at the tank

immediately! Do not use flame for

leak detection.

5. Use only Liquid Propane

6. Use only outdoors

7. Do not over tighten the gas

regulator connection to the unit

with a wrench. This may cause a

crack in the gas regulator.

The purpose of this manual is twofold; one, to provide the installer

with the basic directions and recommendations for the proper

installation and adjustment of the water heater, and two, to the

owner operator, to explain the features, operation, safety

precautions, maintenance and troubleshooting of the water heater.

This manual also includes a parts list.

It is imperative that all persons who are expected to install,

operate, or adjust this water heater read the instructions carefully

so they may understand how to perform these functions. If you do

not understand these instructions or any terms within, seek

professional advice.

ny questions regarding the operation, maintenance service or

warranty of this water heater should be directed to Eccotemp

Systems, LLC directly by calling toll free at 866.356.1992 or via

email at [email protected].

Do not destroy this manual. Please read carefully and keep in a

safe place for future reference.

California Proposition 65 Warning: This product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproduction harm.

Use & Care Manual – L10

WARNING: If the information in these instructions is not followe

exactly, a fire or explosion may result causing property amage,

personal injury or eath.

The Purpose and Benefits th

The Purpose and Benefits thThe Purpose and Benefits th

The Purpose and Benefits the L

e Le L

e L-

-10

1010

The EccoTemp L-10 is a liquid propane fired water heater capable

of delivering 2 to 2.65 gallons of hot water almost anywhere. The

unit has standard 1/2“NPT pipe fittings and an adapter for using a

standard garden hose for inlet water supply.

The L-10 is not a toy. People around the world use similar units to

heat the water in their homes, safely, and reliably.

Gas is supplied from a standard 20 pound propane cylinder (not

included) such as used with outdoor grills. regulator with hose is

furnished with the heater.

The unit includes a stainless steel rain cap that is to help venting

of the flue gases as well as protect it for outdoor usage.

Ignition is automatic and powered by 2 “D” cell batteries (not

included). Burners come on when water flows, and off when the

water is shut off. No pilot light!

ATURAL GAS A D LIQUIEFIED PRETROLEUM MODELS

ATURAL GAS A D LIQUIEFIED PRETROLEUM MODELSATURAL GAS A D LIQUIEFIED PRETROLEUM MODELS

ATURAL GAS A D LIQUIEFIED PRETROLEUM MODELS

Both LP and natural gas have an odorant added to aid in the

detecting a gas leak. Some people may not physically be able to

smell or recognize this odorant. If you are unsure or unfamiliar

with the smell of LP or NG, ask the gas supplier. Other conditions

such as “odorant fade”, which causes the odorant to diminish in

intensity, can also hide or camouflage a gas leak.

•

Water heaters utilizing LP gas are different from natural gas

models. natural gas water heater will not function safely on LP

gas and vice versa

•

No attempt should ever be made to convert the water heater

from NG to LP gas. To avoid possible equipment damage,

personal injury, or fire, do not connect the water heater to a fuel

type not in accordance with the data plate.

•

LP gas must be used with great caution. It is heavier than air

and will collect first in lower areas making it hard to detect at

nose level.

•

Before attempting to light the water heater, make sure to look

and smell for gas leaks. Use a soapy solution to check all gas

fittings and connections. Bubbling at a connection indicates a

leak that must be corrected. When smelling to detect a gas leak,

be sure to sniff near the floor also.

•

Gas detectors are recommended in LP and NG applications and

their installation should be in accordance with the detector

manufacturer’s recommendations and/or local laws, rules,

regulations or customs.

DANGER!

DO NOT RETURN TO STORE:

Eccotemp toll free at 866.356.1992 or via email

at info@eccotemp.com if you encounter a

problem!

TROUBLE SHOOTING

Unit will not start – there are no audible clicks at startup:

a. The first thing to check is to ensure that the incoming water on

the "right" side of the unit. If the incoming and outgoing are

reversed, the unit will not work. The incoming is on the far right

and the outgoing is in the middle.

b. Check to make sure you have fresh batteries and they are

installed in the correct position

c. Number one reason that the unit does not ignite is that there is

not enough water pressure. You need a minimum of 20 PSI

sustained. Municipal water should supply enough water pressure.

Most 12/18/120 pumps well as long as they are capable of

delivering pressure of 30 PSI or greater.

DJUSTMENT: Looking up at the bottom of the unit, you will see

two “slits” in the case where the front and back come together.

Locate the water regulator where you will see two Philip head

screws. Take the screw that is furthest on the right (larger screw)

in about a ¼ or ½ turn. This will enable the unit to operate on a

lower water pressure by restricting flow.

Construction and ame of Parts for the

Construction and ame of Parts for the Construction and ame of Parts for the

Construction and ame of Parts for the

L10 Flue Duct System

L10 Flue Duct SystemL10 Flue Duct System

L10 Flue Duct System

Getting Started

Getting StartedGetting Started

Getting Started

1. Check box for damage. Damages caused in shipment

must be reported immediately.

2. Make sure you have all the parts:

a. Water heater

b. LP gas regulator and hose

c. Rain cap

d. ½” NPT to garden hose adapter

e. Hardware pack

3. Install the rain cap to the top of the flue vent. The rain cap

should fit securely. It is recommended that a beaded layer

of high temperature sealant is used around the perimeter

of the seal between the rain cap and the flue vent.

4. If using a standard garden hose, attach the ½” NPT to

garden hose adapter to the fitting marked “Water Input”.

Use “Teflon” tape or other approved sealing method on

the threads for a secure, water tight fit. Check to make

sure the screen inside the water inlet is in place and clean.

Then attach your water input/garden hose.

5. Install gas supply line and regulator to the unit. DO NOT

OVER TI HTEN. OVER TI HTIN MAY CRACK THE

AS RE ULATOR CAUSIN A AS LEAK! Check for

any gas smell before ignition! Make sure it is screwed all

the way on.

ADJUSTMENT

The temperature of the outgoing water is dependent on the

temperature of the incoming water balanced with the amount of

heat applied. Use extreme caution in setting the outlet water

temperature.

1. With the water regulator set to high, and the gas

regulator set to low, feel the outgoing water. This is

the lowest setting available.

2. To initially raise the outgoing temperature, slowly turn

the gas valve towards maximum. Adjust slowly and

check the temperature often. There will be a slight

delay between increasing the gas supply and the

increase in water temperature.

3. Should the outlet water temperature need to be

higher, slowly reduce the water flow regulator until

desired temperature is reached.

WARNIN :

THE UNIT WILL PRODUCE

TEMPERATURES CAPABLE OF SCALDIN !

6. ttach your water output apparatus to the fitting marked

“Water Outlet”. Do not over tighten! If installing in an

existing water system, connect the hot water line directly

to the ½” NPT fitting.

7. Install two “D” cell batteries in the compartment on the

bottom left of the heater. Check that batteries are facing

the correct direction.

8. Use the top tab on the unit to suspend from a screw

adequate to holding 30 pounds. Place at a comfortable

height without putting stress on the gas hose. If the unit is

to be permanently mounted, use screws to attach the

bottom tab firmly.

9. ttach gas regulator with hose to the LP tank. Use hand

pressure only on the plastic connector. LE VE G S

T NK V LVE IN THE “OFF” POSITION”.

Before going to the USE section:

Check around area for flammables, especially

gasoline or other vapors which may ignite. The

exhaust and top of the unit will get HOT! Make sure

there are no foreign objects around the unit or have

fallen into the top.

Use and Starting

1. Turn on incoming water supply. Ensure that you have

adequate water pressure of between 40-50PSI.

2. Turn your water output device to its “off” position.

3. Turn the gas valve on the cylinder all the way open.

4. IF THE SMELL OF AS IS DETECTED, TURN OFF THE

AS VALVE IMMEDIATELY!!!!

5. Set the water regulator knob on the face of the unit to

its highest setting.

6. Set the gas regulator knob on the face of the unit to

its minimum setting.

7. Turn on your water output device to the “on” position

and adjust to the desired water flow.

8. There will be a series of audible clicks and the burner

will ignite. (Should the burner not ignite after 5

seconds, shut off and go to the “Trouble Shooting”

section.

9. Upon completion of use or storage, open the drain

valve (ribbed cylindrical stem next to the water input

valve) to ensure draining of water.

10. WARNIN : If the outside temperature is around or

below freezing (32 degrees F, 0 degrees C), ensure

that the drain valve is opened and water drained from

the unit after each use to avoid internal damage to the

water regulator. You will also need to unhook the

outgoing water line to ensure that any water in the

heat exchanger is drained. Failure to properly drain

your unit will cause water damage which may or may

not be reparable. Please check the warranty

information found on our website at

www.eccotemp.com/freeze.htm for more information

on freezing issues.

Le but de ce manuel est double; premièrement, de fournir à

l'utilisateur les directions et recommandations de bases pour

l'installation adéquate et ajustements du chauffe-eau, et

deuxièmement, d'expliquer au propriétaire et opérateur, les

fonctions, l'opération, précautions de sécurité, entretien et résolution

des problèmes du chauffe-eau. Ce manuel contient aussi une liste

des pièces.

Il est impératif que toute personne se préparant à installer, faire

fonctionner, ou à ajuster ce chauffe-eau lise les instructions

attentivement pour qu'elle puisse comprendre comment exécuter

ces fonctions. Si vous ne comprenez pas ces instructions ou

quelconques termes ci-contre, ayez recours aux conseils d'un

professionnel.

Toutes questions concernant l'opération, les services d'entretien ou

la garantie de ce chauffe-eau devrait être adressées à Eccotemp

Systems, LLC directement en appelant sans-frais au 866.356.1992

ou via courriel au [email protected].

Ne pas détruire ce manuel. Veuillez le lire attentivement et le

conserver en lieu sûr pour référence future.

vertissement de Californie, Proposition 65 : Ce produit

contient des produits chimiques reconnus par l'État de la

Californie comme étant cancérigènes, causant des

anomalies et nuisances à la naissance.

Manuel ’Utilisation et ’Entretien – L10

AVERTISSEMENT : Si l'information contenue ans ces instructions

n'est pas suivie exactement, un feu ou une explosion pourrait en

résulter, causant ommages à la propriété, blessures personnelles ou la

mort.

NOTE: Before attempting to remove the cover, call technical

support at 866.356.1992

e. wire has become disconnected inside the unit during

shipping. Make sure the gas is OFF. The front cover is held by six

screws, four on top, two on bottom. The knobs pull off. ll the

wiring is done with push together plastic connectors. They are all

visible without further dismantling of the unit. It should be obvious

when a wire has become disconnected.

f. It is possible that some debris or epoxy might have entered the

water regulator. Check to see if the filter screen on the water inlet

is clear of debris. You can also reverse the hookup by taking your

water source and hooking it up to the water outlet side and back

flushing the system.

g. Propane gas cylinders sometimes are contaminated with air,

especially new tanks upon their first filling. Cycle the unit on and

off by using the shower head switch several times (5) to purge the

air from the gas.

Should a unit fail to light or stay lit after 10 cycles, Call

technical support at 808.217.3123 or 866.356.1992.

Units starts, then shuts off:

a. The unit requires a minimum of about 0.5 gallons per minute (2

liters) and a minimum of about 25 PSI* Note, water pressure is at

the lower end of operating parameters. You will need a sustained

water pressure of approximately 40-60 PSI for adequate use if you

are using a 12/18/120 volt pump. See DJUSTMENT in previous

section above.

b. High wind

c. Out of, or low on gas. Propane gas cylinders sometimes are

contaminated with air, especially new tanks upon their first filling.

Cycle the unit on and off by using the shower head switch several

times (5) to purge the air from the gas.

If this doesn't clear the air then the tank must be purged.

d. One of the ignition sensors is bent and/or too close to the

burner. Look to ensure that the ignition pins and the heat sensor

are completely vertical and they do a 90 degree to the back of the

box. If they are not straight (i.e. a 45 degree angle) then you can

straighten them with pliers.

e. The thermocouple is either too high or too low to complete the

circuit. Check to ensure that the thermocouple is flush with the

hole in the heat exchanger.

f. The gas sensor wire (looks like a black ground wire on the gas

regulator) flange might have come loose or is no longer

connected.

g. There is a faulty heat or oxygen sensor. This is usually

diagnosed by taking the front case off of the unit and let it run. If it

continues to operate, then one of the sensors and/or the wire

harness needs to be replaced. This may also be caused by

insufficient clearance on the back of the unit where the majority of

air intake is.

h. The valve on the propane tank should be all the way “Open”.

i.. Fresh batteries are required for ignition spark. Make sure

batteries are aligned in the proper polarity (+/-).

The water does not get hot enough:

a. You are operating the unit above 6,000 feet. While it has been

field tested up to 7,200 feet, we only recommend using it below

elevations of 5,500-6,000 feet.

b. Look into the viewer panes (middle horizontal windows on the

front cover) to see if there is a blue flame. If the flame is yellow

there could be a cracked gas regulator. Do Not ttempt to use the

unit and call Eccotemp directly.

Table des Matières

Table des MatièresTable des Matières

Table des Matières

Introduction à l'Utilisation et à l'Entretien ...................................... 3

VERTISSEMENTS ..................................................................... 4

Utilité et Bénéfices du L-10 ........................................................... 7

Fonctions et Caractéristiques........................................................ 8

Démarrage .................................................................................. 10

Installation/Utilisation .................................................................. 12

justements…………………………………………………………..14

Résolution des Problèmes…………….…………………………... 16

Produits dditionnels .................................................................. 20

Andere Handbücher für L10

Inhaltsverzeichnis

Sprachen:

Andere Eccotemp Boiler Handbücher

Eccotemp

Eccotemp EZ-Flush i12 Bedienungsanleitung

Eccotemp

Eccotemp EP-2.4 Beilage

Eccotemp

Eccotemp 6.5GB BUILDER Series Installationsanleitung

Eccotemp

Eccotemp FVI12 Series Bedienungsanleitung

Eccotemp

Eccotemp EL5 Bedienungsanleitung

Eccotemp

Eccotemp L10 Bedienungsanleitung

Eccotemp

Eccotemp EM-2.5 Beilage

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Eccotemp

Eccotemp 40-HI Bedienungsanleitung

Eccotemp

Eccotemp L10 Bedienungsanleitung

Eccotemp

Eccotemp EM-2.5 Bedienungsanleitung

Eccotemp

Eccotemp EZ-Flush 45-H Bedienungsanleitung

Eccotemp

Eccotemp L5 Bedienungsanleitung

Eccotemp

Eccotemp i12 Series Bedienungsanleitung

Eccotemp

Eccotemp CEL10 Bedienungsanleitung

Eccotemp

Eccotemp 6GB BUILDER Series Installationsanleitung

Eccotemp

Eccotemp SMARTHOME Gebrauchsanweisung

Eccotemp

Eccotemp Schneiders INSTA-HOT pro Bedienungsanleitung

Eccotemp

Eccotemp L7 Bedienungsanleitung

Eccotemp

Eccotemp L10nr Installationsanleitung

Eccotemp

Eccotemp EZ-Flush fvi12 Bedienungsanleitung

Eccotemp

Eccotemp SH22 Bedienungsanleitung

Eccotemp

Eccotemp ET-32 Bedienungsanleitung

Eccotemp

Eccotemp L5 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung