Edelbrock Performer RPM Series Bedienungsanleitung

Catalog #70021 & 70022

Brochure #63-0129

Rev. 7/08 - AJ/mc

Page 1 of 3

Performer RPM Series Upgrade Kits

for the Performer Nitrous Systems

Catalog #70021 & 70022

(For use with kits 70001 & 70002)

INSTALLATION INSTRUCTIONS

Please study all instructions carefully before you install your new Performer RPM Series Upgrade Kit for your Performer

Series Nitrous System. If you have any questions, please call our Technical Hotline at: 1-800-416-8628, 7:00 a.m.

to 5:00 p.m., Monday through Friday, Pacific Standard Time or e-mail us at [email protected].

DESCRIPTION: This kit is intended to enable you to upgrade your Performer Nitrous System to all of the Performer RPM

components and increase the horsepower gain to the RPM levels. Included in this kit is everything you will need to take

your current Performer level nitrous system and upgrade to the Performer RPM level system without having to purchase

a complete kit.

Component Installation

1. First, you will need to remove the Performer plate, gaskets, lines from solenoids to plate, and solenoid mounting

brackets that you had previously installed with your Performer Nitrous System. When you remove your old Performer

Nitrous Plate, be sure you remove all of the gasket material with it.

2. Install your new Performer RPM Nitrous Plate (Item A) onto the carburetor pad using the 2 supplied gaskets

(Items B) with this system.

When installing fittings into the solenoids only use Teflon Paste.Do Not Use Teflon Tape. Teflon tape can break free

inside of the fittings and travel through the system and end up clogging your nitrous or fuel jets or solenoids causing

sever engine damage.

3. Hold the Performer RPM Nitrous Solenoid (Item C) securely, such as in a bench vise, being careful not to harm the

solenoid or block the inlet or outlet of the solenoid.

4. Install the 4AN X ¼” NPT N2O Filter Fitting (Item J) into the inlet port of your Performer RPM Nitrous Solenoid using

Teflon Paste.

5. Install the 4AN X 1/8” NPT Straight Blue Nitrous Fitting (Item M) into the outlet port of your Performer RPM Nitrous

Solenoid using Teflon Paste.

6. Install 1 of the 1-Up Solenoid Brackets (Item E) using two of the Solenoid Mounting Screws (Item F) onto your

Performer RPM Nitrous Solenoid and mount the solenoid in the same location as where you had your Performer Nitrous

Solenoid mounted.

7. Install the 12-inch Steel Braided Nitrous Line (Item H) from the outlet fitting of your Performer RPM Nitrous Solenoid.

8. Once you have made your jetting selection from the next page, install the appropriate nitrous jet into the plate fitting

and install the remaining side of your 12-inch Steel Braided Nitrous Line onto the nitrous fitting of the Performer RPM

Plate with the jet (Item I) in place.

9. Hold the Performer RPM Fuel Solenoid (Item D) securely using the same method you used with your nitrous solenoid.

Install the 6AN X ¼” NPT Red Fuel Fitting (Item K) into the inlet port of your Performer RPM Nitrous Solenoid using

teflon paste.

10. Install the 4AN X 1/8”NPT Straight Red Fuel Fitting (Item L) into the outlet port of your Performer RPM Fuel Solenoid

using Teflon Paste.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Catalog #70021 & 70022

Brochure #63-0129

Rev. 7/08 - AJ/mc

Page 2 of 3

Item Qty. Description

A 1 Performer RPM Plate

B 2 Gaskets

C 1 Performer RPM Nitrous Solenoid

D 1 Performer RPM Fuel Solenoid

E 2 1-up Solenoid Bracket, Performer RPM

F 4 Solenoid Mounting Screws

G 1 8 inch Steel Braided Fuel Line

H 1 12 inch Steel Braided Nitrous Line

I 1 Performer RPM Jet Pack

J 1 4AN X ¼”NPT N2O Filter Fitting

K 1 6AN X ¼”NPT Red Fuel Fitting

L 1 4AN X 1/8”NPT Straight Red Fuel Fitting

M 1 4AN X 1/8”NPT Straight Blue Nitrous Fitting

11. Install the remaining 1-up Solenoid Bracket using the 2 remaining Solenoid Mounting Screws onto your Performer

RPM Fuel Solenoid and mount the solenoid where you had previously mounted your Performer Fuel Solenoid.

12. Install the 8 inch Steel Braided Fuel Line (Item G) to the outlet fitting of your Performer RPM Fuel Solenoid.

13. Install the corresponding fuel jet for the horsepower level you have selected into the inlet fitting on your Performer

RPM Plate.

14. Connect the remaining end of your 8 inch Steel Braided Fuel Line to the inlet fitting of the plate with the jet in place.

Catalog #70021 & 70022

Brochure #63-0129

Rev. 7/08 - AJ/mc

Page 3 of 3

Nitrous and Fuel Jetting Selection

Edelbrock engineering has conducted dyno testing with the Performer RPM Upgrade kit to provide jetting maps for each

horsepower level. The jet combinations are supplied with this system kit to enable you to vary your engine’s power output.

Edelbrock dyno test were conducted at 950 psi nitrous bottle pressure at 6.5 psi fuel pressure. On a typical mildly-

modified 350 cubic-inch engine, you can expect the following approximate power gains for each of the jetting levels:

Square-Flange Jet Map

Spread-Bore Jet Map

Jet Map Footnotes

The jet map above has footnotes that offer the following instructions and technical information:

1 - Use 1 heatrange colder plugs.

2 - Use 2 heatrange colder plugs.

3 - Fuel use 92 octane pump gasoline or better.

4 - Fuel use 110 octane race gasoline or better.

5 - Single Plane manifolds only. DO NOT use a dual plane manifold at this horsepower level.

6. - Advanced tuning required. Suggested timing adjustment is just a guideline. Engine component modifications may

affect timing.

The dyno tests were conducted at Edelbrock using a mildly-modified 350 cubic-inch engine. Both dual-plane and open-

plenum intake manifolds were tested to ensure validity of jetting maps for each horsepower setting. Modifications

included Edelbrock intake manifolds, Edelbrock aluminum heads, dyno headers, and improved ignition. We also used

different grades of fuel and colder plugs during the testing. All stated timing adjustments listed in jet maps is where the

motor being tested worked best. Final timing should be adjusted to achieve best power and/or MPH per application.

See section “5.0 Ignition Timing and Nitrous” for more info on timing selection.

Any variation in jetting patterns other than what is listed above and engine damage could occur. Please contact the

Edelbrock Technical Department with any questions you have concerning jetting patterns and their effects on engine

performance.

Footnote 5:

Horsepower settings of 200 and 250 are for single plane manifolds only. In testing, we found that dual plane manifolds

have some distribution problems at these super high flowrates that could cause engine damage. Please contact the

Edelbrock Technical department with any questions you have concerning jetting patterns and their effects on engine

performance when using a dual plane manifold.

HP Gain Nitrous Jet Fuel Jet Timing Adjustment Footnotes

100 57 57 3°-5° Retard 1, 3

150 68 68 5°-7° Retard 1, 3

175 78 78 6°-8° Retard 1, 3

200 85 85 7°-9° Retard 2, 4, 5, 6

250 99 99 9°-11° Retard 2, 4, 5, 6

HP Gain Nitrous Jet Fuel Jet Timing Adjustment Footnotes

100 59 59 3°-5° Retard 1, 3

150 71 71 5°-7° Retard 1, 3

175 81 81 6°-8° Retard 1, 3

Catalog #70021 & 70022

Brochure #63-0129

Rev. 7/08 - AJ/mc

Edelbrock Corporation 2700 California Street Torrance, CA 90503

Tech Line: (800) 416-8628 Tech Fax: (310) 972-2730 Tech E-Mail: [email protected]

Dieses Handbuch passt für folgende Modelle

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 68712 Bedienungsanleitung

Edelbrock

Edelbrock 3881 Bedienungsanleitung

Edelbrock

Edelbrock 33505 Bedienungsanleitung

Edelbrock

Edelbrock Performer-Plus 2157 Bedienungsanleitung

Edelbrock

Edelbrock 70028 Bedienungsanleitung

Edelbrock

Edelbrock 2162 Gebrauchsanweisung

Edelbrock

Edelbrock 25-9492 Bedienungsanleitung

Edelbrock

Edelbrock Nitrous Refill Station 78000 Bedienungsanleitung

Edelbrock

Edelbrock 65102 Bedienungsanleitung

Edelbrock

Edelbrock 67082 Bedienungsanleitung

Edelbrock

Edelbrock 2103 Gebrauchsanweisung

Edelbrock

Edelbrock 305 Gebrauchsanweisung

Edelbrock

Edelbrock 1727 Bedienungsanleitung

Edelbrock

Edelbrock 66162 Bedienungsanleitung

Edelbrock

Edelbrock 68452 Bedienungsanleitung

Edelbrock

Edelbrock 65003 Bedienungsanleitung

Edelbrock

Edelbrock 2114 Bedienungsanleitung

Edelbrock

Edelbrock ENDURASHINE 63-0299 Bedienungsanleitung

Edelbrock

Edelbrock 5419 Bedienungsanleitung

Edelbrock

Edelbrock Honda Civic 67342 Bedienungsanleitung

Edelbrock

Edelbrock 5670 Bedienungsanleitung

Edelbrock

Edelbrock 61409 Bedienungsanleitung

Edelbrock

Edelbrock 72282 Bedienungsanleitung

Edelbrock

Edelbrock 97383 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung