Edge-Core AS7712-32X Bedienungsanleitung

– 1 –

Quick Start Guide

1. Unpack the Switch and Check Contents

AS7712-32X

100G Data Center Switch

Rack Mounting Kit—2 front-post brackets, 2 rear-post

brackets, 20 screws, and 2 ear-locking screws

Power Cord—Japan, US, Continental Europe, or UK

Console Cable—RJ-45 to DB-9

Documentation—Quick Start Guide (this document)

and Safety and Regulatory Information

Note:

The switch has the Open Network Install

Environment (ONIE) software installer pre-loaded on the

switch, but no switch software image. Information about

compatible switch software can be found at

www.edge-core.com.

Caution:

The switch includes plug-in power supply (PSU)

and fan tray modules that are installed into its chassis. All

rear-installed modules must have a matching airflow

direction. That is, if the installed power modules have a

front-to-back (F2B) airflow direction, all the installed fan

tray modules must also have a F2B airflow direction.

The airflow direction of PSU and fan tray modules is

indicated by the color the release lever or handle on the

modules. Blue indicates an intake (cool) airflow, and red

indicates an exhaust (warm) airflow. Therefore, the fan tray

handles and PSU release levers must always be the same

color, either all blue or all red. The airflow direction of fan

tray modules is also indicated by labels on the modules.

2. Mount the Switch

Attach each of the front- and rear-post brackets to the

switch using four of the included bracket screws.

Use an additional two screws to secure each of the rear-post

brackets at the mid-point on the sides of the switch.

Use the screws and cage nuts supplied with the rack to

secure the switch in the rack.

Lock the position of the rear-post bracket ears using the

included position-locking screws.

You can also adjust the rear-post bracket ears to fit different

rack depths from 56 cm to 85 cm.

Caution:

Installing the switch in a rack requires two

people. One person should position the switch in the rack,

while the other secures it using the rack screws.

装置の吸排気に必要な領域をマニュアル上に規定して

いる。

3. Ground the Switch

Ensure the rack is properly grounded and in compliance

with ETSI ETS 300 253. Verify that there is a good electrical

connection to the grounding point on the rack (no paint or

isolating surface treatment).

Attach a lug (not provided) to an 18 AWG minimum

grounding wire (not provided), and connect it to the

grounding point on the switch rear panel. Then connect the

other end of the wire to rack ground.

Caution:

The earth connection must not be removed

unless all supply connections have been disconnected.

4. Connect Power

Install one or two AC power modules in the switch.

The switch supports up to two PSUs that must have the

same matching airflow direction as the installed fan tray.

Connect an external AC power source to the modules.

E102015-CS-R01

150200001281A

www.edge-core.com

32-Port 100G Ethernet Data Center Spine Switch

AS7712-32X

Quick Start Guide

– 2 –

5. Verify Switch Operation

Verify basic switch operation by checking the system LEDs.

When operating normally, the PS1/PS2, Diag, and Fan LEDs

should all be on green.

6. Perform Initial System Boot

If the network operating system (NOS) installer is located on

a network server, first connect the RJ-45 Management

(Mgmt) port to the network using 100-ohm Category 5, 5e

or better twisted-pair cable. (Not required if the NOS

installer is located on attached storage.)

Boot the switch. Wait for the ONIE software to locate and

execute the NOS installer, and then wait for the installer to

load the NOS software image.

Subsequent switch boots will bypass ONIE and directly run

the NOS software.

Note:

Refer to the network operating system (NOS)installer

and NOS documentation for details on software options and

set up for ONIE.

7. Connect Network Cables

For the RJ-45 Management port, connect 100-ohm Category

5, 5e or better twisted-pair cable.

Connect DAC cables directly to the QSFP28 slots. Or first

install QSFP28 transceivers in the slots and then connect

fiber optic cabling to the transceiver ports.

As connections are made, check the port status LEDs to be

sure the links are valid. Each QSFP28 port has four LEDs that

indicate valid links in the following modes:

◆1 LED Blue — 100 Gbps mode

◆1 LED Orange — 40 Gbps mode

◆1-4 LEDs White — 25 Gbps breakout mode (four lanes)

◆1-4 LEDs Green — 10 Gbps breakout mode (four lanes)

8. View the Product Label

The switch product label is located below the Console and

Management ports on the right side of the front panel. Pull

the label out to view the product information.

Hardware Specifications

Switch Chassis

Size (WxDxH) 438.4 x 515 x 43.5 mm (17.26 x 20.28 x 1.71 inch)

Weight 10.87 kg (23.96 lb), with two installed PSUs

Temperature Operating (F2B): 0° C to 45° C (32° F to 113° F)

Operating (B2F): 0° C to 40° C (32° F to 104° F)

Storage: -40° C to 70° C (-40° F to 158° F)

Humidity Operating: 5% to 95% (non-condensing)

Power

Consumption

550 Watts maximum

AC PSU

Power AC

Input Rating

100–240 VAC, 50-60 Hz, 650 Watts, hot pluggable

System AC

Input

100–240 VAC, 50-60 Hz, 6 A max.

Power DC

Output Rating

5 VDC @ 4 A

12 VDC @ 52 A

Regulatory Compliances

Emissions EN 55022:2010, Class A

EN 61000-3-2:2009, Class A

EN 61000-3-3:2008

FCC Class A

VCCI Class A

CE Mark

Immunity EN 55024:2010

IEC 61000-4-2/3/4/5/6/8/11

Safety UL (CSA 22.2 No 60950-1 & UL60950-1)

CB (IEC/EN60950-1)

Andere Handbücher für AS7712-32X

Andere Edge-Core Netzwerk-Router Handbücher

Edge-Core

Edge-Core ECS3510-28T Programmierhandbuch

Edge-Core

Edge-Core AS4630-54TE Bedienungsanleitung

Edge-Core

Edge-Core VR-100 Bedienungsanleitung

Edge-Core

Edge-Core Wedge100BF-32QS Bedienungsanleitung

Edge-Core

Edge-Core ECS4210-12P Bedienungsanleitung

Edge-Core

Edge-Core ECS2000-50T Bedienungsanleitung

Edge-Core

Edge-Core EC3805F Bedienungsanleitung

Edge-Core

Edge-Core ECS4100-26TX Bedienungsanleitung

Edge-Core

Edge-Core ES4626 Bedienungsanleitung

Edge-Core

Edge-Core AS5710-54X Bedienungsanleitung

Edge-Core

Edge-Core ES3526XA Bedienungsanleitung

Edge-Core

Edge-Core AS7926-40XKFB Bedienungsanleitung

Edge-Core

Edge-Core AS9516-32D Bedienungsanleitung

Edge-Core

Edge-Core AS7946-30XB Bedienungsanleitung

Edge-Core

Edge-Core ES4624-SFP Programmierhandbuch

Edge-Core

Edge-Core ECIS4500 Series Bedienungsanleitung

Edge-Core

Edge-Core AS7316-26XB Bedienungsanleitung

Edge-Core

Edge-Core EWS100 Bedienungsanleitung

Edge-Core

Edge-Core ECS3510-26P Programmierhandbuch

Edge-Core

Edge-Core ECS4620-28F Bedienungsanleitung

Edge-Core

Edge-Core ES4624-SFP Programmierhandbuch

Edge-Core

Edge-Core AS5835-54X Bedienungsanleitung

Edge-Core

Edge-Core ES3528M-PoE Bedienungsanleitung

Edge-Core

Edge-Core ECS3610-28T Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise