Edimax EN-9220F-64 Bedienungsanleitung
L
A
N
P
R
O
F
E
S
S
I
O
N
A
L
64/32bit 66/33MHz PCI
Gigabit Adapter
Gigabit Ethernet Adapter
EN-9220F-64
User’s Manual
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply
with the limits of a Class B computing devices,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
If you suspect this product is causing interference, turn
your computer on and off while your radio or TV is
showing interference. If the interference disappears
then when you turn the computer off and reappears then
you turn the computer on, something in the computer is
causing interference.
You can try to correct the interference by one or more
of the following measures :
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
difference from that to which the receiver is
connected.
4. Ensure that all expansion slots (on the back or side
of the computer) are covered. Also ensure that all
metal retaining brackets are tightly attached to the
computer.
1
1Introduction
Thanks you for purchasing our Gigabit Fast Ethernet
Adapter. This guide is to provide the installation and
usage of this adapter for network installers and users.
The Gigabit network adapter complies to 32/64 bit PCI
specification and supports full duplex feature which can
double network speed.
This adapter supports 1000Mbps network speed, comply
with IEEE 802.3z standard and operates on 1000Base-SX
Multi Mode Fiber.
This adapter supplies many drivers including NDIS 4,5
driver for Microsoft Windows 95 OSR2, 98, Me, NT,
2000, XP, Novell Netware Server 5.x, Novell Netware
ODI for DOS and Linux. Whatever your requirements
are ease of installation, superior performance or
responsive support backed up by unlimited technical
support, this adapter is the superior choice.
1
2
2Features & Specifications
(1) Features & Benefits
ySupports 64/32-bit, 66/33MHz PCI Bus Master for high
performance and low processor utilization.
yComplies with the IEEE 802.3z standard.
yFull duplex design to double the performance to
2000Mbps.
yOne Fiber SC connector for 1000Mbps network speed.
• Auto-setups IRQ and I/O address.
• NDIS 4,5 driver for Microsoft Windows 95 OSR2, 98,
Me, NT, 2000, XP, Novell Netware Server 5.x, Novell
Netware ODI for DOS and Linux.
yProvide two LEDs to indicate network link/activity and
full duplex function.
2
(2) Technical Specification
yConnector : Fiber SC ×1
yStandard : IEEE 802.3z
yTransmission Rate : 1000Mbps / 2000Mbps
yHardware Required : IBM compatible PC with
available PCI slot
( PCI 2.1/2.2 ),66/33MHz,
32bit & 64bit
yIRQ Line : Assigned by system
yI/O Address : Assigned by system
yDrivers : NDIS 4,5 driver for Microsoft
Windows 95 OSR2, 98, Me,
NT, 2000, XP, Novell Netware
Server 5.x, Novell Netware ODI
for DOS, Linux
yLEDs : 1000Mbps Link/Activity
Full duplex
yTemperature : 00C to 550C (Operating)
yHumidity : 10% to 90% (Non-condensing)
yCertification : FCC Class B, CE Mark
yDimension : 165 x 58 mm
yWeight : 85g (Max.)
3
3
3Installation
(1) Hardware Installation
To insert the network adapter into your PC, follow the
steps bellow :
1. Turn off the computer and remove its cover.
2. Insert the adapter into a PCI slot.
3. Secure this adapter to the rear of the computer
chassis and put back the computer cover.
4. Connect the adapter to the network using Fiber SC
cable.
(2) Driver Installation
Use the drivers supplied by the diskette included in this
product. For detail description, please execute the
readme.exe in the root of directory of the diskette
provided by this product.
4
4
4Trouble-shooting
If you experience any problems with the adapter, first
make sure the appropriate driver is loaded, the proper
cable is connected to the adapter port and the
hub/switch complies with the adapter specification,
such as 1000BaseFX, then check the LED.
The adapter provides two LEDs to indicate network
status.
1000 Link/Activity
The LED indicates if the 1000Mbps (Gigabit) Fiber
has been LINK ok or not. When the light is OFF, it
indicates that the 1000Mbps Fiber port has not been
connected or LINK not ok. When the light is ON, it
indicates that the 1000Mbps Fiber port LINK ok.
When the light is BLINKING, it indicates that there is
traffic flow on the network which the adapter is
connected to.
Full duplex
The LED indicates if the 1000Mbps fiber is in full
duplex mode. The light is ON when the 1000Mbps
fiber port is in full duplex mode.
5
TRADEMARKS
Copyright 2001/2002 by the manufacturer of this
product. No part of this manual may be reproduced,
transcribed, stored in a retrieval system, translated into
any language or computer language without the prior
written consent of the manufacturer.
All brand and product names are trademarks and/or
registered trademarks of their respective companies.
Inhaltsverzeichnis
Andere Edimax Adapter Handbücher
Edimax
Edimax EW-7717Un Bedienungsanleitung
Edimax
Edimax EW-7811UAC Bedienungsanleitung
Edimax
Edimax EW-7718Un Bedienungsanleitung
Edimax
Edimax HP-5001 Bedienungsanleitung
Edimax
Edimax EW-7612UAN Bedienungsanleitung
Edimax
Edimax EW-7722PnD Bedienungsanleitung
Edimax
Edimax EW-7722UTn V3 Bedienungsanleitung
Edimax
Edimax HP-5101KK Bedienungsanleitung
Edimax
Edimax EW-7612UAn V2 Bedienungsanleitung
Edimax
Edimax EN-9130TX Bedienungsanleitung
Edimax
Edimax HP-5102ACK Bedienungsanleitung
Edimax
Edimax HP-5102K Bedienungsanleitung
Edimax
Edimax HP-6002AC Bedienungsanleitung
Edimax
Edimax EW-7711UAn Bedienungsanleitung
Edimax
Edimax EW-7822GTN 3.0A Bedienungsanleitung
Edimax
Edimax EN-9130TXA Bedienungsanleitung
Edimax
Edimax EN-9130TX Bedienungsanleitung
Edimax
Edimax HP-5102 Bedienungsanleitung
Edimax
Edimax EN-9230TX-32 Bedienungsanleitung
Edimax
Edimax HP-5102AC Bedienungsanleitung
