Eibach MULTI-PRO-R2 Bedienungsanleitung

D3157 - Page 1

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

PARTS & HARDWARE LIST

Part Number Description Qty Part Number Description Qty

A 4017.8300 DAMPER ASSY FRONT 2 D PDK4.TOOL 4mm ADJUSTMENT TOOL 1

B 4020.8400 DAMPER ASSY REAR 2 E PDK6.TOOL 6mm ADJUSTMENT TOOL 1

C UB0120 RESERVOIR CLAMP 2 F PDR.TOOL REBOUND TOOL 1

PARTS IDENTIFIER

NOTES: Read All Instructions Before Beginning Installation

Installation of a Eibach Multi-Pro Coil-Over set should only be performed by a qualified mechanic experienced in the

installation and removal of suspension components.

Use of a hoist is highly recommended and will substantially reduce installation time.

Never work on or under a vehicle unless it is properly supported by safety stands and wheels are blocked.

Never use impact wrenches or guns to install or remove shock absorber piston components, shafts and piston rod

nuts.

After installation, it is always important to inspect and adjust the following if necessary:

- Wheel alignment such as camber, caster & toe.

- Tire and/or wheel fender clearance.

- Brake line clearance and attachments.

- Brake anti-locking and anti-skid system sensors.

Alignment: After installation, you will need a full vehicle alignment to ensure proper tire wear and performance.

Height Adjustment – Should be performed with the wheels completely off the ground and with the springs fully

unloaded.

D3157 - Page 2

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

FRONT SUSPENSION REMOVAL

1. Raise the car off the ground and make sure it’s

properly supported with jack stands. Note: Never

work on or underneath a car that is not properly

supported with safety stands.

2. Remove the wheels from the vehicle.

3. Loosen and remove the two screws that secure the

brake line to the side of the strut. (See Photo 1)

4. Loosen and remove the bolt and nut that secures

the fork to the lower control arm. (See Photo 2)

5. Loosen and remove the bolt that secures the fork to

the OE strut, then, lower the fork down as shown.

(See Photos 3 & 4)

Photo 3

Photo 1

Photo 5

Photo 4

Photo 2

D3157 - Page 3

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

6. Loosen and remove the upper strut mount nuts,

then, remove the strut as shown.

(See Photos 5 & 6)

FRONT SUSPENSION INSTALLATION

1. Install the Eibach Multi Pro coilover into the vehicle

and secure it to the strut tower using the provided

hardware. (See Photo 7)

2. Slide the OE fork onto the bottom of the Eibach

Multi Pro coilover, and secure it with the OE screw.

(See Photo 8)

3. Secure the fork to the lower control arm using the

OE hardware removed in step 4 of the removal

process. Note: Be sure to preload the

suspension prior to tightening this bolt.

Uneven lowering and premature wear to the

control arm bushing will result if not done

properly. (See Photo 9)

Photo 7

Photo 8

Photo 6

Photo 9

D3157 - Page 4

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

4. Using a grinder or cut off wheel, cut the tab off of

the brake line bracket (See Arrows) as shown.

Then secure the bracket to the coilover using the

OE hardware and the provided cap screw. (See

Photos 10, 11 & 12)

5. Route the reservoir into the engine compartment

and mount it to a suitable location using the

provided reservoir clamp and hardware.

6. Double check to make sure everything is properly

positioned, then, tighten all hardware.

Photo 12

Photo 11

Photo 10

D3157 - Page 5

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

REAR SUSPENSION REMOVAL

1. Remove the interior access panels (both left and

right side) and remove the upper shock mount nuts.

(See Photo 13)

2. Remove the lower shock mount bolt, then, slide the

shock downward, and remove the strut as shown

(See Photos 14, 15 & 16)

Photo 14

Photo 13

Photo 15

D3157 - Page 6

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

REAR SUSPENSION INSTALLATION

1. Install the Eibach Multi-Pro coilover into the lower

control arm with the reservoir facing the front of the

car, slide it as far down as possible, then, slide the

coilover upward into the upper OE mounting holes

and secure it with the provided nuts. (See Photos

17, 18 & 19) Note: Do not tighten at this time

2. Secure the coilover to the lower control arm using

the OE hardware. (See Photo 20) Note: Be sure

to preload the suspension prior to tightening

this bolt. Uneven lowering and premature wear

to the control arm bushing will result if not done

properly.

Photo 17

Photo 20

Photo 18

Photo 19

D3157 - Page 7

Eibach Springs, Inc. | 256 Mariah Circle | Corona | California 92879-1751 | USA

T +1 951-256-8300

www.eibach.com

MULTI-PRO-R2 | INSTALLATION INSTRUCTIONS

1997-01 Acura Integra, Type-R, DC2

PART NUMBER 4020.713

PERFORMANCE SUSPENSION AUTOMOTIVE OEM/OES HI-TECH INDUSTRIAL

ADJUSTMENT PROCEDURE /

RECOMMENDATIONS

COMPRESSION AND REBOUND SETTINGS

1. The shocks in this kit are adjustable for compression

and rebound dampening forces. The following steps

explain the adjustable features of this kit.

2. Turning the compression adjustment knob in a

clockwise or (+ pos.) direction increases the amount of

force necessary to compress the shock. Likewise

turning the knob in a counterclockwise or (–neg.)

direction decreases the amount of force to compress

the shock. Note : The compression adjustment is

located on the reservoir.

Turning the rebound adjustment knob in a clockwise or

(+ pos.) direction increases the rebound forces.

Likewise turning the knob in a counterclockwise or (-

neg.) direction decreases the rebound forces. NOTE:

The rebound adjustment for the coil-over is located

at the top of the shock.

Tightening torque for piston rod nut

Thread Size Nm ft-lb Thread Size Nm ft-lb Thread Size Nm ft-lb

M8 25 18 M12 x 1.25 35 26 M14 x 1.50 50 37

M10 x 1.0 20 15 M12 x 1.50 40 29 M16 x 1.50 50 37

M10 x 1.25 20 15

Inhaltsverzeichnis

Andere Eibach Andere Handbücher

Eibach

Eibach Multi-Pro R1 Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch