EINHELL BG-PW 48 Bedienungsanleitung

Operating Instructions

Petrol Water Pump

Art.-Nr.: 41.713.43 I.-Nr.: 11010 BG-PW 48

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:33 Uhr Seite 1

Read and follow the operating instructions and safety information

before using for the first time.

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:33 Uhr Seite 2

213 14 15 16 20 21

17 1918

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:33 Uhr Seite 3

3 4

5a 5b

6a 6b

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 4

76c

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 5

Table of contents

1. Safety regulations

2. Layout

3. Intended use

4. Technical data

5. Before putting the equipment into operation

6. Operation

7. Cleaning, maintenance, storage and ordering of spare parts

8. Disposal and recycling

9. Troubleshooting guide

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 12

Important!

When using equipment, a few safety precautions

must be observed to avoid injuries and damage.

Please read the complete operating manual with due

care. Keep this manual in a safe place, so that the

information is available at all times. If you give the

equipment to any other person, give them these

operating instructions as well.

We accept no liability for damage or accidents which

arise due to non-observance of these instructions

and the safety information.

1. Safety information

Please refer to the booklet included in delivery for the

safety instructions.

CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations

and instructions may result in an electric shock, fire

and/or serious injury.

Keep all safety regulations and instructions in a

safe place for future use.

2. Layout (Fig. 1/4)

1 Tank cover

2 Refilling nozzle with screw

3 Pressure connection

4 Oil filler plug

5 Oil drain plug

6 ON/OFF switch

7 Reversing starter

8 Petrol cock

9 Choke lever

10 Throttle control

11 Suction connection

12 Water emptying plug

13 2x Threaded connector 1” external thread

14 2x Threaded connector 1.25” external thread

15 2x Hose connector 2“

16 3x Hose clip

17 2x Seal

18 2x Union nut

19 Intake cage

20 Spark plug wrench

21 Oil filler funnel

3. Proper use

The machine is suitable for irrigating and watering

landscaped areas, vegetable beds and gardens and

for operating lawn sprinklers.

The water can be taken from ponds, streams,

rainwater butts, rainwater cisterns and springs if an

initial filter is fitted.

The maximum temperature of the fluid must not

exceed +35°C if the machine is operated

permanently.

Clean water (sweet water), rainwater and low

concentrations of washing lye can be used as the

transport medium. The machine must not be used to

transport inflammable, gassing, explosive and

aggressive fluids (such as petrol, acids, lyes, silo

percolating juice, etc.) and fluids that contain

abrasive substances (such as sand).

The machine is to be used only for its prescribed

purpose. Any other use is deemed to be a case of

misuse. The user / operator and not the

manufacturer will be liable for any damage or injuries

of any kind caused as a result of this.

Please note that our equipment has not been

designed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 13

4. Technical data

Engine type: 4-stroke engine; air-cooled

Max. engine output: 4.8 kW / 6.5 bhp

Displacement: 196 cc

Idle speed of engine: 1500 rpm

Maximum engine speed: 3600 rpm

Fuel: Regular unleaded petrol

Tank capacity: 3.6 l

Oil volume / type: 600 mL SAE#30

Spark plug: L7TC

Max. intake head: 6 m

Max. pumping rate: 35000 l/h

Max. delivery head: 26 m

Max. pressure: 2.6 bar

Weight (with empty tank): 28 kg

Intake/Discharge connector: 2” hose connection

2” / 1.25“/ 1” thread connector

LWA sound power level: 95 dB

LpA sound pressure level: 75 dB

5. Before starting

As a basic principle, we recommend the use of a

preliminary filter and a suction set with suction hose,

suction strainer and non-return valve, in order to

prevent long priming periods and unnecessary

damage to the pump as a result of stones and solid

foreign bodies.

5.1 Preparing the machine

앬Fill the engine with engine oil (see also point

7.2.1 Oil change).

앬Fill the tank with petrol.

앬Place the machine on a flat, firm surface.

5.2 Connecting and routing the intake and

discharge lines

앬Connect the intake line to the intake connection

(Figure 3 / Item 11) and the discharge line to the

discharge connection (Figure 3 / Item 3).

앬Position the intake line so that it rises from the

water withdrawal point to the pump. It is essential

that you do not route the intake line above the

height of the pump. Air bubbles in the intake line

will slow down and prevent the intake process.

앬Install the intake and discharge lines in such a

way that they do not exert any mechanical

pressure on the pump.

앬The intake valve should be low enough in the

water to ensure that if the water level falls, the

pump will not run dry.

앬A leaking intake line will draw in air and therefore

not draw in any water.

앬Do not draw in any foreign bodies (sand, etc.). If

necessary install an initial filter.

6. Operation

The pump must be filled with the transport fluid at the

filler neck (Figure 3 / Item 2) before the engine is

started.

Note: We advise that you install a non-return valve in

the intake line and fill it with water before you start

the machine for the first time.

6.1 Starting the engine

1. Set the On/Off switch (Figure 1 / Item 6) to “ON”.

2. Set the petrol cock (Figure 4 / Item 8) to the “ON”

position.

3. If the engine is cold, set the choke lever (Figure

4 / Item 9) to “Choke”.

4. Move the throttle lever (Figure 4 / Item 10) to the

center position.

5. Pull the starter cord (Figure 4 / Item 7) until the

engine starts.

6. When the engine has been running for approx.

30 seconds, move the choke lever to “Run”.

If the engine is warm, leave the choke lever in the

“Run” position when starting.

Explanation of the positions of the throttle lever

(Figure 4 / Item 10):

“Tortoise”:

Engine in idling

“Hare”:

Maximum delivery rate

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 14

6.2 Intake process

앬During the priming process, the shut-off devices

present in the pressure pipe (spray nozzles,

valves etc.) must be completely open so that the

air in the suction pipe can escape freely.

앬Depending on the suction height and the air

quantity in the suction pipe, the initial priming

process can last for approx. 0.5 min. – 5 min. In

the case of longer priming periods, top up again

with water.

앬If the pump is removed after use, it is essential

that it is filled with water again the next time it is

connected and started.

6.3 Stopping the engine

앬Set the On/Off switch to “OFF”.

앬Close the petrol cock.

Running-in period:

For the first 20 hours of operation, the motor

must not be operated at full throttle for too long.

Misfires, start-up difficulties:

Check whether

앬fuel is flowing into the carburetor;

앬the fuel filter is clean;

앬the carburetor air valve is open;

앬the air filter is clean;

앬the spark plug is clean and the electrode gap is

between 0.6 and 0.7mm.

7. Cleaning, maintenance, storage and

ordering of spare parts

Disconnect the spark plug boot before doing any

cleaning and maintenance work!

7.1 Cleaning

Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

We recommend that you clean the device

immediately each time you have finished using it.

Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts

of the equipment. Ensure that no water can seep

into the device.

7.2 Maintenance

In this connection, please also read the attached

service information

7.2.1 Changing the oil

The engine oil is best changed when the engine is at

working temperature

앬Use only engine oil (10W40).

앬Place the machine on a slightly inclined surface

so that the oil drain plug is at the lower end

(Figure 5a / Item A).

앬Remove the oil filler screw (Figure 5a / Item B).

앬Remove the oil drain plug and drain the warm

engine oil into a suitable container.

앬After all the oil has drained, screw in the oil drain

plug and place the machine on a flat surface.

앬Insert fresh engine oil up to the top mark on the

oil dipstick (Figure 5b / Item H).

Important. Only inset the oil dipstick to check

the oil level. Do not screw it in.

While the machine is working, the oil level must be

between the two marks “L” and “H” (Figure 5b).

Dispose of the waste oil properly.

7.2.2 Air filter

Clean the air filter at regular intervals, and replace it if

necessary.

앬Remove the screw from the air filter cover (Figure

6a)

앬Remove the air filter cover.

앬Remove the screw from the air filter element

(Figure 6b)

앬Remove the air filter element (Figure 6c).

앬Clean the air filter by tapping it, blowing it out

with compressed air or by washing it with soap

suds. Important. Leave the air filter to dry before

you refit it.

앬Assemble in reverse order.

7.2.3 Spark plug

Clean the spark plug at regular intervals, and replace

it if necessary. Set the electrode gap to 0.6 mm.

앬Remove the spark plug boot by twisting it (Figure

앬Remove the spark plug using a spark plug

wrench

앬Clean the spark plug with a copper wire brush or

fit a new one.

앬Assemble in reverse order.

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 15

7.3 Storage

앬Rinse the pump thoroughly with water before

lengthy periods of inactivity or winter storage.

앬Close the petrol cock and allow the engine to run

until it stops to empty the carburetor.

앬Fill the tank fully to prevent rust formation.

앬Remove the drain plug (Figure 3 / Item 12) and

fully drain the pump housing.

앬Store the machine in a dry place out of the reach

of children.

7.4 Ordering replacement parts

Please quote the following data when ordering

replacement parts:

Type of machine

Article number of the machine

Identification number of the machine

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its being

damaged in transit. This packaging is raw material

and can therefore be reused or can be returned to

the raw material system.

The unit and its accessories are made of various

types of material, such as metal and plastic.

Defective components must be disposed of as

special waste. Ask your dealer or your local council.

Anleitung_BG_PW_48_SPK1:_ 25.06.2008 9:34 Uhr Seite 16

Inhaltsverzeichnis

Andere EINHELL Wasserpumpe Handbücher

EINHELL

EINHELL GC-DW 900 N Bedienungsanleitung

EINHELL

EINHELL ROYAL SMP 402-S Bedienungsanleitung

EINHELL

EINHELL GE-SP 750 LL Bedienungsanleitung

EINHELL

EINHELL BG-PW 18 Bedienungsanleitung

EINHELL

EINHELL 41.734.22 Bedienungsanleitung

EINHELL

EINHELL GE-AW 9041 E Bedienungsanleitung

EINHELL

EINHELL GP 2800 Bedienungsanleitung

EINHELL

EINHELL GP JET 1201 INOX Bedienungsanleitung

EINHELL

EINHELL 400 RB Bedienungsanleitung

EINHELL

EINHELL GE-GP 1145 ECO Bedienungsanleitung

EINHELL

EINHELL ROYAL SMP 400-S Bedienungsanleitung

EINHELL

EINHELL ROYAL TDM 1000-S Bedienungsanleitung

EINHELL

EINHELL BG-GP 1355 N Bedienungsanleitung

EINHELL

EINHELL GC-SP 5511 IF Bedienungsanleitung

EINHELL

EINHELL GH-PW 18 Bedienungsanleitung

EINHELL

EINHELL GC-GP 1046N Bedienungsanleitung

EINHELL

EINHELL GH-PW 18 Bedienungsanleitung

EINHELL

EINHELL GC-DP 1340 G Bedienungsanleitung

EINHELL

EINHELL GC-DP 7835 Bedienungsanleitung

EINHELL

EINHELL GH-DP 5225 N Bedienungsanleitung

EINHELL

EINHELL GE-PW 46 Bedienungsanleitung

EINHELL

EINHELL GC-GP 1045 Bedienungsanleitung

EINHELL

EINHELL GC-WW 6538 Bedienungsanleitung

EINHELL

EINHELL GC-DW 900 N Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung