EINHELL RG-AW 1139 Bedienungsanleitung

tOriginal operating instructions

Garden Pump



Art.-Nr.: 41.770.02 I.-Nr.: 11010 RG-AW 1139

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 1

Read and follow the operating instructions and safety information

before using for the first time.



Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 2

2 3

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 3

Important!

When using equipment, a few safety precautions

must be observed to avoid injuries and damage.

Please read the complete operating manual with due

care. Keep this manual in a safe place, so that the

information is available at all times. If you give the

equipment to any other person, give them these

operating instructions as well.

We accept no liability for damage or accidents which

arise due to non-observance of these instructions and

the safety information.

1. Safety regulations

 Caution!

In stagnant water bodies, garden ponds, dams

and their surrounding areas the unit may only be

used with an earth-leakage circuit breaker with

an actuating rated current of up to 30 mA

(according to VDE 0100 Part 702 and 738).

The equipment is not designed for use in

swimming pools and paddling pools of any kind

or other bodies of water in which people or

animals may be present during operation. It is

prohibited to operate the equipment if a person

or animal is in the danger area. Ask your

electrician!

This equipment is not designed to be used by people

(including children) with limited physical, sensory or

mental capacities or those with no experience and/or

knowledge unless they are supervised by a person

who is responsible for their safety or they have

received instructions from such a person in how to

use the equipment safely. Children must always be

supervised in order to ensure that they do not play

with the equipment.

Important!

Always inspect the equipment visually before

using it. Do not use the equipment if safety

devices are damaged or worn. Never disable

safety devices.

Use the equipment only for the purposes

indicated in these operating instructions.

You are responsible for safety in the work area.

If the cable or plug is damaged by external

influences, the cable may not be repaired. The

cable must be replaced by a new one. This work

may only be carried out by a trained electrician.

The voltage of 230 V alternating voltage specified

on the rating plate must be the same as the mains

voltage.

Never use the power cable to lift, transport or

secure the equipment.

Ensure that the electrical plug connections are in

areas that are not at risk of flooding or protect

them from moisture.

Pull the mains plug before starting any work on

the equipment.

Do not expose the equipment to a direct jet of

water.

The operator is responsible for complying with

local safety and installation regulations. (Ask an

electrician if you are in any doubt.)

Consequential damage caused by flooded rooms

in the event of the equipment suffering faults must

be prevented by the user by means of suitable

measures (for example installing alarm systems

or a reserve pump, etc.).

In the event of a failure, repair work may only be

carried out by an electrician or by ISC after sales

service personnel.

The equipment must never run dry or be used

when the intake line is closed fully. The

manufacturer’s warranty does not cover damage

caused to the equipment as a result of running it

dry.

The pump must not be used to operate swimming

pools.

The equipment must not be installed in the

drinking water pipe line.

 CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations

and instructions may result in an electric shock, fire

and/or serious injury.

Keep all safety regulations and instructions in a

safe place for future use.

2. Layout and items supplied (Fig. 1-2)

1. Pressure connector

2. Carry handle

3. Power switch

4. Water drain screw

5. Suction connector

6. Coarse filter screw

7. Ventilation screw

8. Coarse filter

Not illustrated: Operating instructions

Take all parts out of the packaging and check that the

equipment is complete.

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 4

3. Items supplied

Open the packaging and take out the equipment

with care.

Remove the packaging material and any

packaging and/or transportation braces (if

available).

Check to see if all items are supplied.

Inspect the equipment and accessories for

transport damage.

If possible, please keep the packaging until the

end of the guarantee period.

IMPORTANT

The equipment and packaging material are not

toys. Do not let children play with plastic bags,

foils or small parts. There is a danger of

swallowing or suffocating!

Original operating instructions

Safety instructions

4. Proper use

Applications

Irrigation and watering of green areas, vegetable

beds and gardens.

Operation of lawn sprinklers.

For drawing water from ponds, streams, rainwater

butts, rainwater cisterns and springs

For supplying service water

Transport media:

For the pumping of clear water (fresh water),

rainwater or light suds/service water.

The maximum temperature of the fluid must not

exceed +35°C if the equipment is operated

permanently.

Do not use the equipment to pump inflammable,

gassing or explosive fluids.

The pumping of aggressive liquids (acids, alkalis,

silo seepage etc.) as well as liquids with abrasive

substances (sand) must likewise be avoided.

This equipment is not designed to convey

drinking water.

The equipment is to be used only for its prescribed

purpose. Any other use is deemed to be a case of

misuse. The user / operator and not the manufacturer

will be liable for any damage or injuries of any kind

caused as a result of this.

Please note that our equipment has not been

designed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

5. Technical data

Mains connection 240V ~ 50 Hz

Power rating 1100 W

Pumping rate 4100 l/h

Max. delivery head 48 m

Max. delivery pressure 0.48 MPa (4.8 bar)

Max. suction height 8 m

Pressure and suction connector R1 internal thread

Max. water temperature 35 °C

6. Before putting the equipment into

operation

6.1 Connecting the intake line

As a basic principle, we recommend the use of a

preliminary filter and a suction set with suction hose,

suction strainer and non-return valve, in order to

prevent long priming periods and unnecessary

damage to the pump as a result of stones and solid

foreign bodies.

The intake hose or pipe should have a minimum

diameter of 25 mm (1”); a diameter of 32 mm

(1 1/4”) is recommended for suction heights

exceeding 5 m.

Connect the intake valve (foot valve) with intake

cage to the intake line.

Position the intake line so that it rises from the

water withdrawal point to the equipment. Avoid

positioning the suction pipe higher than the

pump, as this would delay the escape of air

bubbles from the suction pipe and impede the

priming process.

Install the intake and discharge lines in such a

way that they do not exert any mechanical

pressure on the equipment.

The intake valve should be low enough in the

water to ensure that if the water level falls, the

equipment will not run dry.

A leaking intake line will draw in air and therefore

not draw in any water.

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 5

6.2 Connecting the discharge line

The discharge line (min. 19 (3/4”)) must be

connected to the R1 (1”) female thread discharge

line connector of the equipment either directly or

with the aid of a threaded nipple.

With the right couplings it is also possible, of

course, to use a 13 mm (1/2“) delivery hose. The

smaller delivery hose results in a lower delivery

rate.

During the priming operation, fully open any shut-

off mechanisms (spray nozzles, valves, etc.) in

the pressure line so that the air can escape

without obstruction.

6.3 Electrical connections

Connect the appliance to a 240 V ~ 50 Hz socket-

outlet with earthing contact. Minimum fuse 10

ampere.

A built-in thermostat protects the motor from

overloading and blocking. The pump is switched

off automatically by the thermostat if overheating

occurs and is switched on again automatically

after cooling.

7. Operation

Install the equipment on a solid and level surface.

Remove the ventilation screw (7).

Unscrew the coarse filter screw (6) and remove

the coarse filter (8) as shown in Figure 2. Now

you can fill the pump housing with water via the

coarse filter screw (6). Filling the intake line

accelerates the intake process.

Assemble in reverse order.

Open the discharge line.

Connect the mains cable.

Switch on the equipment with the power switch

(3) - water can be suctioned in for up to 5 minutes

(maximum suction height).

After finishing the work, switch off the equipment

with the power switch (3).

8. Replacing the power cable

If the power cable for this equipment is damaged, it

must be replaced by the manufacturer or its after-

sales service or similarly trained personnel to avoid

danger.

9. Cleaning, maintenance and

ordering of spare parts

The equipment is almost completely maintenance

free. In order to ensure a long service life, however,

we recommend that you regularly check and care for

the product.

Important!

The equipment must be disconnected from the power

supply (pull the power plug) prior to performing any

maintenance.

9.1 Servicing

If the equipment becomes clogged, connect the

discharge line to the water line and disconnect

the suction hose. Open the water line. Switch on

the equipment several times for approx.

two seconds. This should resolve the majority of

clog-related problems.

Replacing the mains cable: Important:

Disconnect the equipment from the power

supply! A defective mains cable may only be

replaced by a qualified electrician.

There are no parts inside the equipment which

require additional maintenance.

9.2 Cleaning the coarse filter insert

Clean the coarse filter insert at regular intervals,

and replace it if necessary.

Remove the coarse filter screw (6) and coarse

filter (8) (Figure 2).

Disassemble the coarse filter insert as shown in

Figure 3.

Do not use abrasive cleaning agents or petrol to

clean the coarse filter.

Clean the coarse filter by tapping it on a flat

surface. In cases of stubborn dirt first clean with

soapy water, then rinse with clear water and air-

dry.

Assemble in reverse order.

9.3 Storage

If the pump is not going to be used for a long time

or has to be removed for the winter months, rinse

it out with water, empty it completely and allow it

to dry.

The equipment must be completely drained

before it is subjected to frost.

After long stoppages, make sure the rotor turns

correctly by briefly switching the pump on and off.

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 6

9.4 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

Type of machine

Article number of the machine

Identification number of the machine

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

10. Disposal and recycling

The unit is supplied in packaging to prevent its being

damaged in transit. This packaging is raw material

and can therefore be reused or can be returned to the

raw material system.

The unit and its accessories are made of various

types of material, such as metal and plastic. Defective

components must be disposed of as special waste.

Ask your dealer or your local council.

11. Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing

temperature. The ideal storage temperature is

between 5 and 30 °C. Store the electric tool in its

original packaging.

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 7

Faults Cause Remedy

Motor fails to start up - No mains voltage

- Pump rotor blocked -thermostat

switched off

- Check voltage

- Dismantle and clean pump

No intake - Non-return valve dirty

- Pump chamber without water

connection

- Air in intake line air-tight

- Max. suction height exceeded

- clean

- Fill water into intake

- Make sure intake line is close

- Check suction height

Inadequate delivery rate - Suction height too high

- Coarse filter dirty

- Water level falling rapidly

- Pump performance diminishedby

contaminants part

- Check suction height

- clean

- Place the suction hose at a

deeper level

- Clean pump and replace wearing

Thermostat switches pump off - Motor overloaded - friction

caused by foreign substances

too high

- Dismantle and clean pump.

Prevent intake of foreign

substances (filter)

12. Troubleshooting guide

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 8

tFor EU countries only

Never place any electric tools in your household refuse.

To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its

implementation in national laws, old electric tools have to be separated from other waste and disposed

of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the demand to return electrical devices:

As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the

device is properly recycled if ownership is relinquished. This can also be done by handing over the used

device to a returns center, which will dispose of it in accordance with national commercial and industrial

waste management legislation. This does not apply to the accessories and auxiliary equipment without

any electrical components which are included with the used device.

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 9



The reprinting or reproduction by any other means, in whole or in part,

of documentation and papers accompanying products is permitted only

with the express consent of ISC GmbH.

 Technical changes subject to change

Anleitung_RG_AW_1139_SPK7:_ 07.05.2010 14:45 Uhr Seite 10

Andere Handbücher für RG-AW 1139

Inhaltsverzeichnis

Andere EINHELL Wasserpumpe Handbücher

EINHELL

EINHELL GH-DP 6315 N Bedienungsanleitung

EINHELL

EINHELL RG-DP 8535 Bedienungsanleitung

EINHELL

EINHELL NEW GENERATION NFP 750 Bedienungsanleitung

EINHELL

EINHELL GC-DW 1000 N Bedienungsanleitung

EINHELL

EINHELL GC-DP 3325 Bedienungsanleitung

EINHELL

EINHELL GE-WW 9041 E Bedienungsanleitung

EINHELL

EINHELL ROYAL TDM 1000-S Bedienungsanleitung

EINHELL

EINHELL GE-PW 46 Bedienungsanleitung

EINHELL

EINHELL GE-PP 5555 RB-A Bedienungsanleitung

EINHELL

EINHELL ROYAL RBP 18 Bedienungsanleitung

EINHELL

EINHELL GC-GP 6036 Bedienungsanleitung

EINHELL

EINHELL ROYAL GPK 1500 Niro Bedienungsanleitung

EINHELL

EINHELL ROYAL TMP 255-S Bedienungsanleitung

EINHELL

EINHELL GC-DP 7835 Bedienungsanleitung

EINHELL

EINHELL AQUINNA 4180403 Bedienungsanleitung

EINHELL

EINHELL GE-SP 4390 LL ECO Bedienungsanleitung

EINHELL

EINHELL LE-HW 1300 Niro Bedienungsanleitung

EINHELL

EINHELL GP-F 1300 Niro Bedienungsanleitung

EINHELL

EINHELL GE-DP 7330 LL ECO Bedienungsanleitung

EINHELL

EINHELL GP JET 900/1 NIRO Bedienungsanleitung

EINHELL

EINHELL GH-SP 2768 Bedienungsanleitung

EINHELL

EINHELL BG-WW 1038 N Bedienungsanleitung

EINHELL

EINHELL GC-DP 5010 G Bedienungsanleitung

EINHELL

EINHELL BG-SP 400 RB Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung