EK DP-2 Bedienungsanleitung
1
DP-2
Wireless Contact Sensor
User manual
2
Features
The wireless contact sensor is an accessory of smart alarm system. It’s
fashion design, energy saving, and low battery warning supported. The
system would inform users to replace the battery by App when needed. It’s
easy to setup and works well with most doors and windows. When trans-
mitter and magnet are apart, the sensor triggers alarm. Transmitter can be
put on either of magnet’s left or right side.
Parameters
Working Voltage
CC 3V
Battery
1 × CR2032 button battery (3V)
Working Current
20mA
Standby Current
2μA
Transmission
distance Without obstacle 200m
Transmission
frequency
433,92MHz
Working
Temperature
-10°C~40°C
Humidity < 90% (non-condensing)
Dimension
35.5g(battery not included) 40g(battery included)
Weight
Transmitter: 80.0mm*38.2mm*13.3mm Magnet:
80.0mm*14.8*12.9mm (L*W*H)
Magnet: 80.0mm*14.8*12.9mm (L*W*H)
3
Appearance / PCB Layout
LED Indication
LED flashes once: Door/window is opened and transmitter sends signal to
the main panel. LED lights stays on: Low battery, please replace the battery
immediately.
Operating Instructions
1. Working principle
• The transmitter sends trigger signal to main panel paired when the magnet moun-
ted near ismoved apart.
2. Pairing with main panel Scanning the QR Code for Pairing.
• Scan the QR code printed on this accessory by App.
• The pairing result would be confirmed in App.
Learn Mode
• Launch the App/PC client for turn on Learn Mode.
LED Indicator
Magnet Transmitter
4
• Follow the guideline in App/PC client to trigger the accessory for the system to
learn.
• The pairing result would be confirmed in App/PC client. Hint:
How to trigger
• Remove the battery insulating sheet.
• Move the magnet around transmitter until the red LED indicator lights up.
I nstallation & Notice
• Open the case and remove the battery insulative strip.
• Pairing to main panel by App before installing.
• Attach the transmitter and magnet seperately on door/window and its frame with
double-side sticky tape or fix with screws. Transmitter can be put on either of mag-
net’s left or right side.
• Make sure the distance between transmitter and magnet is less than 1cm and at the
same level.
• Avoid installing the sensors in area with a large amount of metal or electric wire.
5
Entry Delay & Home Arm Settings
This sensor supports Entry Delay and Home Arm features. Which can be
adjusted in App/PC client.
Entry Delay feature : when the sensor is triggered while the system is in
Arm/Home Arm status, the
system will wait for preset time until the alarm goes o.
Home Arm feature : when the sensor with this feature enabled is triggered
while the system is in Home
Arm status, the alarm will go o.
- For networking alarm system, this sensor could be checked in Entry De-
lay and Home Arm list of the
App to turn on/o each feature.
- For other alarm system, this sensor could enable/disable with Entry De-
lay or Home Arm feature in
Accessory Management function of App/PC client.
Battery replacement instructions
1 Insert the flat blade
of a small screw-driver
into the pry-o slot
of transmitter, twist the
blade to remove the
cover.
2 Remove the used
battery and replace
with 1× CR2032 battery
with the plus (+) symbol
facing up.
6
EKSELANS by ITS
ITS Partner O.B.S. S.L
Av. Corts Catalanes 9-11
08173 Sant Cugat del Vallès
Barcelona (Spain)
Tel: +34 935839543
Inhaltsverzeichnis
Andere EK Zubehör Handbücher
