Ekinex EK-DF2-TP Gebrauchsanweisung

Application manual

Indoor presence sensors

EK-DF2-TP

EK-DG2-TP

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

Contents

1Scope of the document.............................................................................................................................. 3

2Product description.................................................................................................................................... 4

3Main features............................................................................................................................................. 4

4Technical data............................................................................................................................................ 4

5Switching, display and detection elements................................................................................................ 5

6Operation................................................................................................................................................... 5

6.1 Brightness measurement...................................................................................................................... 5

6.2 Lighting control channels...................................................................................................................... 5

6.3 Constant ambient brightness regulation ............................................................................................... 5

6.4 HVAC control channels......................................................................................................................... 5

7Positioning ................................................................................................................................................. 6

7.1 Positioning for EK-DF2-TP.................................................................................................................... 6

7.2 Positioning for EK-DG2-TP................................................................................................................... 6

8Limitation of the detection area.................................................................................................................. 8

9Installation.................................................................................................................................................. 9

10 Connection of the KNX bus line............................................................................................................... 11

11 Conﬁguration and commissioning............................................................................................................ 11

12 Walk test.................................................................................................................................................. 12

13 List of ETS parameters............................................................................................................................ 13

13.1 Menu: General .................................................................................................................................... 13

13.2 Menu: Motion sensors......................................................................................................................... 13

13.3 Menus: Light control output C1 / C2 ................................................................................................... 14

13.4 Menus: HVAC control output C3 / C4................................................................................................. 15

13.5 Menus: Alarm function ........................................................................................................................ 16

14 Elenco oggetti di comunicazione ETS..................................................................................................... 17

15 Troubleshooting....................................................................................................................................... 19

16 Package contents .................................................................................................................................... 19

17 Optional accessories ............................................................................................................................... 20

18 Dimensions.............................................................................................................................................. 21

19 Markings .................................................................................................................................................. 21

20 Maintenance ............................................................................................................................................ 21

21 Disposal................................................................................................................................................... 22

22 General warnings..................................................................................................................................... 22

23 Other information..................................................................................................................................... 22

Revision

Changes

Date

Written by

Verified by

1.2

Minor corrections

2020-02-06

G.Croci C.

1.1

Minor corrections

2020-01-14

G.Croci C.

1.0

First issue

2019-12-11

G.Croci C.

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

1 Scope of the document

This application manual describes application details for the ekinex® presence / movement sensors

EK-DF2-TP and EK-DG2-TP.

The document is aimed at the system configurator as a description and reference of device features

and application programming. For installation, mechanical and electrical details of the device please

refer to the technical description datasheet.

Application manual and application programs for ETS are available for download at

www.ekinex.com.

Item

File name (## = release)

Version

Device rel.

Update

Technical datasheet

STEKDF2TP_IT.pdf

STEKDG2TP_IT.pdf

A1.0

11 Dic 2019

Application manual

MAEKDF2DG2TP_IT.pdf

Application program

APEKDF2TP##.knxprod

APEKDG2TP##.knxprod

You can access the most up-to-date version of the full documentation for the device using following

QR codes:

EK-DF2-TP EK-DG2-TP

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

2 Product description

The ekinex® presence sensors EK-DF2-TP and EK-DG2-TP are flush-mount ceiling passive infrared

(PIR) motion detectors, for the detection of movement / presence of people in indoor environments

in order to drive lighting and HVAC systems.

The devices have the same functionality and differ only in the aspects listed below.

Throughout the manual, both devices will be referenced indifferently; the respective different

features will be pointed out wherever required.

The detection area, which has a coverage angle of 360°, can be extended using other sensors

conﬁgured as slave devices.

An integratedlight sensor, combinedwith themotion detector, can managelight switching depending

on brightness level as well as presence.

The device has two distinct output channels for lighting, with independent parameters; the operation

can be automatic or semi automatic.

The device is also capable of maintaining a constant brightness level in the room by controlling a

dimmable light source.

All of the above parameters can be set by the user either through ETS or by means of a dedicated

IR remote during installation.

The device has two additional HVAC channels, which act in a similar way as the Light Control

channels but without the standby time and light level dependence.

An additional alarm channel can switch the load on or off depending on the number of trigger events

(movements) detected in a time frame of configurable duration.

3 Main features

•Semi-automatic or fully automatic operation

•Two independent Light control channels

•Two independent HVAC control channels

•One alarm channel

•An additional device can be used as slave for any of the channels

•Detection span of 360°, sectors can be masked through optical shields

•Adjustable Sensitivity, with "Walk test" to verify detection range

•Most parameters can be set from ETS or through an IR remote

4 Technical data

•Rated voltage: 24 Vdc (21 - 30 Vdc) supplied by KNX bus

•Current consumption (on KNX bus): max 10 mA (operation) / 5 mA (Standby)

•Detection range: 360° circular (maskable), up to 9m diameter at 2.5m mounting height

•Light measurement range: 10..2000 Lux

•Housing, lens and frame in plastic material

•Safety standards: IEC 61000-6-1 / IEC 61000-6-3 / EN 55014 / EN 50491

•Dimensions:

oBody diameterØ 60 mm

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

oRim diameter Ø 75 mm

oMounting Hole diameter Ø 65 mm

oTotal height 78 mm

oRecess depth 72 mm

•Environmental conditions:

oOperating temperature: - 20 ... + 40°C

oRelative humidity: 95% not condensing

oEnvironmental protection: IP20

5 Switching, display and detection elements

The device is equipped with:

•on the rear side, a programming pushbutton

•visible through the plastic lens, a blue programming LED, a red signalling LED, a PIR sensor,

a brightness sensor and an IR receiver.

6 Operation

The sensor reacts to the thermal radiation emitted by moving bodies; the detection area is optically

divided in small sections through a composite lens. A person walking in the detection area across

the sections triggers the sensor.

6.1 Brightness measurement

The measurement of the room brightness is carried out by an integrated light sensor with linear

output and optical ﬁlter set on the proﬁle of the human eye. The brightness value, measured in Lux,

can be transmitted on the bus.

6.2 Lighting control channels

The lighting channel has two operation modes, Automatic or Semi-automatic. The automatic mode

controls both switch-on and switch-off; the semi-automatic mode only controls switch-off after a

manual switch-on.

The lighting source can be controlled through two different types of communication objects: On-Off

switch or Absolute dimming percentage.

In automatic mode, a load connected to a lighting channel will be switched on when movement is

detected and (if desired) the ambient light level is below a preset brightness value.

When no movement has been detected for a programmable time duration, a stand-by phase can be

entered, during which the light can be dimmed to alower intensity; if nofurther movement is detected,

once stand-by time has expired, the light will be automatically switched off.

Both the light level threshold and stand-by time functions can be disabled if not required.

6.3 Constant ambient brightness regulation

The internal brightness sensor can be used to maintain a constant ambient brightness if a dimmable

light source is available. The light source must be capable of being controlled through a Relative

dimming communication object.

6.4 HVAC control channels

The HVAC channels act in a similar way as the Light Control channels, but without the standby time

and the dependence from the light level.

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

7 Positioning

The actual detection range of the sensors depends on the mounting height.

The optimal range is achieved walking through several portions of the detection area.

7.1 Positioning for EK-DF2-TP

For the EK-DF2-TP sensor, at a standard mounting height of 2.5 m, presence detection range (for

small movements) is about 4 meters of diameter, while movement detection range (person walking

through the detection area) is about 9 meters of diameter.

The recommended mounting height varies from 2 m up to 5 m.

7.2 Positioning for EK-DG2-TP

For the EK-DG2-TP sensor, at a standard mounting height of 2.5 m, presence detection range (for

small movements) is about 3 meters of diameter, while movement detection range (person walking

through the detection area) is about 12 meters of diameter.

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

Since the detector responds to temperature change, be aware that following conditions may

cause lower sensitivity:

•In very foggy days, the sensitivity may be less due to moisture collecting on

the lens.

•In very hot days, the sensitivity may be less since high ambient temperature

is close to body temperature.

•In very cold days when heavy clothing is worn, especially if the facial area is

covered, very little heat will be emitted from the body causing the unit to be

less sensitive.

Please also verify following conditions during installation:

•Avoid pointing the detector toward objects with highly reflective surfaces,

such as mirrors, glass, etc.

•Avoid mounting the detector very close to heat sources, such as heating

vents, air conditioners, lights, etc.

•Avoid pointing the detector toward objects which may sway in air currents,

such as curtains, tall plants, etc.

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

8 Limitation of the detection area

The detection area can be limited, in order to avoid unwanted activations, by means of the supplied

optical shielding filters.

Cut the supplied shield in such a way to remove the sectors corresponding to the desired detection

area as in following figure:

EK-DF2-TP

EK-DG2-TP

Apply the shield by inserting its edge between the lens and the rim:

Section of shield

applied

Active range

(h = 2.5m)

Settore

-30° per settore

A + B + C

Ø 2 m

A + B

Ø 5 m

Ø 7 m

Nessuna

Ø 9 m

Section of shield

applied

Active range

(h = 2.5m)

Settore

-30° per settore

A + B + C

Ø 2 m

A + B

Ø 5 m

Ø 8 m

Nessuna

Ø 12 m

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

EK-DF2-TP EK-DG2-TP

When the device is installed in place, make sure that the shield is in the correct position according

to the required area masking.

9 Installation

Warning! The electrical connection ofthe device can be carried out only by qualified

personnel. The incorrect installation may result in electric shock or fire. Before

making the electrical connections, make sure the power supply has been turned oﬀ.

Warning! In order to supply the KNX bus lines use only KNX bus power supplies

(e.g. ekinex EK-AB1- TP or EK-AG1-TP). The use of other power supplies can

compromise the communication and damage the devices connected to the bus.

The device has degree of protection IP20, and is therefore suitable for use in a dry indoor

environment.

The device can be flush mounted through a 65 mm (EK-DF2-TP) / 68 mm (EK-DG2-TP) diameter

hole on a ceiling board with 5 mm to 25 mm thickness.

EK-DF2-TP EK-DG2-TP

For solid ceilings, a plastic barrel-shaped plastic support for external mounting is available as an

accessory.

Application manual

Presence / movement sensors EK-DF2/DG2-TP

Rev. 1.2 - 2020-02-06 MAEKDF2DG2TP_EN

Warning:

•Do not mount on conductive surface.

•Do not open the enclosure frequently.

•The sensor is a low voltage circuit; never connect it with the 230V line network.

•Do not run the KNX wiring in the same conduit used by line network wiring.

Connect the device to the bus cable terminated by the standard terminal block on the back of the

device. EK-DG2-TP

At this point it is recommended to carry out the commissioning of the device (see “Commissioning”),

or at least the download of the physical address, using the programming button placed close to the

bus connector; alternatively, programming mode can be activated later when the device is already

installed by means of the EK-QR6-IR remote controller.

To insert the device into the hole on the ceiling board, raise and hold the spring clips; guide them

into the hole and gently slide the body of the sensor until it falls into place.

EK-DF2-TP EK-DG2-TP

To remove the sensor, gently pry under the external rim with a screwdriver or another flat object;

once you can get a firm hold with your hands on the rim, pull gently but firmly to extract the body of

the sensor.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ekinex Zubehör Handbücher

Ekinex

Ekinex EK-DB2-TP Gebrauchsanweisung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung