Ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on February 14th 2017

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus XI

HERO RGB Hero motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 4 screws on

the back of the motherboard that need to be removed in order to remove the factory

installed MOSFET heat pipe cooling solution.

1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat

spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm

thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

2.. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the

motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]

Do not remove

the PCH (SB)

Cooler!

Installation manual for EK-FB ASUS Maximus XI HERO water block

CPU socket

M9H PCH

(SB)

Mosfets

1. Thermal pad F–1.0mm

(for mosfets):

1. Thermal pad F–1.0mm

(for inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on February 14th 2017

STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB Maximus XI HERO Monoblock series water block gently to the motherboard or vice versa (as shown on

photo below). Make sure that mounting holes are aligned. There is no use for M2.5 adhesive PVC washer on Maximus XI HERO motherboard (as the motherboard has its

own washers already glued by manufacturer)

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use four (4) M2,5x5 AX1 screws with PVC washers. Tighten the

screws evenly. Do not use excessive force when tightening the screws!

B) CPU part: Use four (4) M4x8 DIN7984 with screws and washers.

Tighten the screws using enclosed 2.5mm Allen key.

Use the enclosed screws and washers as shown in picture below:

For the EK-FB Maximus XI HERO Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE

INLET PORT. EK recommends the use of EK-ACF fittings. When using fittings other

than EK-ACF series please use hose clamps or appropriate substitute to secure the

tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is

always recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

M4x8 screws

PVC washer

M2,5x5 AX1 screws

3. PLACING THERMAL PADS ON

MOTHERBOARD. Place thermal pads on PCB as

shown on the picture

PLEASE REMOVE THE PROTECTIVE FOIL

FROM BOTH SIDES OF THE THERMAL PADS

PRIOR TO INSTALLATION!

Place 1mm thermal pads in larger

strips over marked area and make

sure all mosfet chips are covered.

Place 1mm thermal pads in larger

strips over marked area and make

sure all Inductor chips are covered.

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-FC Titan XXL Handbuch

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC 6970 V2 Handbuch

ekwb

ekwb EK-Vector Strix RTX 2070 Backplate Leitfaden

ekwb

ekwb EK-FC 6970 V2 Handbuch

ekwb

ekwb EK-FC R9 Fury X Leitfaden

ekwb

ekwb EK-FB GA AX370 Gaming RGB Monoblock Bedienungsanleitung

ekwb

ekwb 3831109816202 Leitfaden

ekwb

ekwb EK-DBAY DCP 2.2 Handbuch

ekwb

ekwb Velocity-AMD Bedienungsanleitung

ekwb

ekwb EK-FB EVGA X58 LE Leitfaden

ekwb

ekwb EK-FC7870 GTX Handbuch

ekwb

ekwb EK-Quantum Magnitude sTRX4 Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum ROG Zenith II Extreme Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Strix X299-E RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB ASR Z77 Extreme11 Leitfaden

ekwb

ekwb EK-Classic AM4 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASRock X299 RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC790 Leitfaden

ekwb

ekwb EK-FC980 GTX Ti WF3 Handbuch

ekwb

ekwb EK-XRES Revo D5 Bedienungsanleitung

ekwb

ekwb EK-FC 5870 V2 Handbuch

ekwb

ekwb GTX 1080 Ti Aorus Backplate Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB ASUS Maximus XI HERO Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken