Ekwb EK-FB EVGA X58 LE Leitfaden

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sample photo of EVGA X58 LE PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 6 screws on the back of

the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Northbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. One thermal pad (90x15x1 mm) and 2 (30x25x0,5) thermal

pads are enclosed with your water block. Please cut thermal pads as shown bellow.

(WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS

PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB EVGA X58 LE water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon7thofAugust,2009.

Southbridge

Northbridge

Mosfets

CPUsocket

18x4x0,5mm

75x7,5x1mm

25x25x0,5mm

18x4x1mm

12x4x0,5mm

12x4x1mm

Applythermalgreasehere.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric.

Thermal paste provides enough adhesive force for standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water block or

vice versa and attach it with enclosed screws as shown. Make sure that mounting

holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the Northbridge, and continue evenly outwards. Do not use too much pressure

screws (be very careful around Southbridge and use small amount of tightening force, since block has no standoffs. EKWB recommends

tightening screws around Southbridge in the end.), because motherboard might

bend and either cause bad contact with water block, or break

a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA X58 LE series are usually sold with

high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always

recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2,5x6 DIN7985

Please use the enclosed insulating

washers on all M2,5x6mm screws.

Fitting/barb

Spacer

Washer

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-XRES DCP 2.2 Reservoir Handbuch

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series Bedienungsanleitung

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Bedienungsanleitung

ekwb

ekwb EK-FC7950 Handbuch

ekwb

ekwb EK-FC Titan X Leitfaden

ekwb

ekwb EK-RAM Dominator Handbuch

ekwb

ekwb EK-RES X3 Series Handbuch

ekwb

ekwb EK-FC Titan Z water block Handbuch

ekwb

ekwb EK-FB KIT ASUS R4BE Leitfaden

ekwb

ekwb EK-FB ASUS Z270E Strix Monoblock Series Bedienungsanleitung

ekwb

ekwb EK-Quantum Velocity Ryzen Edition UNC Standoffs -... Bedienungsanleitung

ekwb

ekwb EK-FB ASUS M6I Leitfaden

ekwb

ekwb EK-FC670 GTX DCII Leitfaden

ekwb

ekwb EK-FC980 GTX TF5 Handbuch

ekwb

ekwb EK-AIO 120 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS ROG ZE Monoblock Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector FE RTX 3070 Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Ti WF3 Handbuch

ekwb

ekwb EK-Quantum Kinetic TBE 120 VTX PWM Bedienungsanleitung

ekwb

ekwb EK-FB KIT RE4 Handbuch

ekwb

ekwb EK-FB ASRock X299 RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-Dual DDC X-Top CSQ Handbuch

ekwb

ekwb EK-XRES DCP 4.0 Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB EVGA X58 LE Leitfaden

Beliebte Computerhardware Handbücher anderer Marken