Ekwb EK-Quantum Momentum ROG Zenith II Extreme Bedienungsanleitung

USER GUIDE

MONOBLOCK

EK-Quantum

Momentum ROG Zenith II Extreme

This product is intended for installation by expert users only.

Please consult with a qualified technician. Improper installation

may result in damage to your equipment. EK Water Blocks

assumes no liability whatsoever, expressed or implied, for the use

of these products or their installation. The following instructions

are subject to change without notice. Please visit our website

at www.ekwb.com for updates. Before the installation of this

product, please read important notice, disclosure, and warranty

conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

Carefully read the manual before you start with the

installation process!

Remove your motherboard from the computer to ensure the

safest mounting method and prevent any possible damage to

your CPU and/or motherboard’s circuit board (PCB).

The EK ﬁttings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with rubber

o-ring gaskets.

The use of high-quality market-proven corrosion inhibiting

coolants is always strongly recommended for any liquid

cooling system.

- 3 -

TABLE OF CONTENT

PREPARING YOUR MOTHERBOARD 4

REMOVING THE STOCK COOLER 4

APPLYING THE THERMAL COMPOUND 6

CUTTING THERMAL PADS 6

PLACING THE THERMAL PADS 7

PLACING THE BLOCK ON THE MOTHERBOARD 7

ATTACHING THE BLOCK TO THE MOTHERBOARD 8

PLACING THE REPLACEMENT HEATSINK ON THE MOTHERBOARD 9

CONNECTING THE DRGB LED STRIP 11

REQUIRED TOOLS 11

SUPPORT AND SERVICE 12

SOCIAL MEDIA 12

- 4 -

PREPARING YOUR MOTHERBOARD

REMOVING THE STOCK COOLER

STEP 1

Remove all encircled screws. There are nine (9) screws that need to

be removed (see sample image). Save the standoffs and backplate

screws for later use. There is no need to remove the factory backplate.

STEP 1

- 5 -

STEP 2

The additional four (4) screws need to be removed in order to

disconnect the I/O cover screen. After ﬁnishing the installation

process, the cover can be mounted back onto the motherboard.

Under marked part, carefully disconnect the I/O screen connectors.

STEP 2

- 6 -

APPLYING THE THERMAL COMPOUND

Apply the enclosed thermal compound on the CPU heat spreader

(as shown in the image). There is no need to cover the whole IHS.

Applying too much thermal grease will have a negative impact on

cooling performance!

CUTTING THERMAL PADS

Your block comes with thermal pads that need to be trimmed in order

to ﬁt the voltage regulation area (MOSFET) on the motherboard’s

circuit board.

1. Thermal PAD F 1,0mm - (120x16mm) EAN: 3830046996732

2. Thermal PAD F 1,5mm - (120x16mm) EAN: 3830046996749

WARNING: Dimensions on pictures below are scaled.

Thermal Pad F – 1.0 mm

120

Thermal Pad F – 1.5 mm

120

- 7 -

PLACING THE THERMAL PADS

Place thermal pads on the motherboard, as shown in the image.

REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF

A THERMAL PAD PRIOR TO INSTALLATION.

Thermal Pad F 1.0mm

PLACING THE BLOCK ON THE MOTHERBOARD

Place the EK-Quantum Momentum ROG Zenith II Extreme water

block to the motherboard or vice versa (as shown in the image).

Make sure that the mounting holes are aligned.

Thermal Pad

F 1.5mm

- 8 -

ATTACHING THE BLOCK TO THE

MOTHERBOARD

STEP 1

Prior to fastening the screws, please make sure the mounting holes

on the motherboard’s circuit board are aligned with the water block.

STEP 2 (CPU)

Carefully tighten all the marked screws using a 2.5mm Allen Key. Do

not apply excessive force.

STEP 2

STEP 3 (MOSFET)

Use two (2) stock cooler screws. Tighten the screws evenly.

Stock Cooler Screw

CPU

Screw

STEP 3

Factory

Backplate

- 9 -

PLACING THE REPLACEMENT HEATSINK

ON THE MOTHERBOARD

STEP 1

Take off four (4) standoffs from the original heatsink using the EK-Loop

Wrench and attach them to the replacement heatsink that comes with

the EK-Quantum Momentum ROG Zenith II Extreme monoblock.

STEP 1

STEP 2

Before placing the replacement heatsink on the motherboard, attach

the I/O cover screen to the replacement heatsink and secure it with

ﬁve (5) factory-provided I/O cover screws. Make sure to connect all

the connectors.

STEP 2

STEP 3

Carefully place the replacement heatsink on the motherboard, as

shown in the image. Make sure the Thermal Pad is positioned correctly.

Stock CoolerStandoffs

Replacement Heatsink

- 10 -

STEP 5

We recommend you use the EK ﬁttings. When using ﬁttings of other

brands, please prepare the hose clamps or an appropriate substitute

to secure the tubing to the barb. The use of corrosion-inhibiting

coolant containing biocide is always recommended for any liquid

cooling system.

STEP 5

Use this opening

as an Inlet Port!

Tubing

EK-Fitting

STEP 4

Attach the replacement heatsink using the factory I/O cover

screws and a Phillips head screwdriver. Also, pay attention not

to use too much force while pressing the replacement heatsink

down to the motherboard.

Heatsink Screws

STEP 4

Factory Backplate

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-RAM Dominator Handbuch

ekwb

ekwb EK-FB GA X299 GAMING Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC6990 Handbuch

ekwb

ekwb EK-Quantum Momentum ROG Crosshair VIII Hero Bedienungsanleitung

ekwb

ekwb EK-FC 770 GTX DCII Handbuch

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON RGB... Bedienungsanleitung

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FB ASUS R5-E10 Leitfaden

ekwb

ekwb EK-FB KIT EVGA SR-X Installationsanleitung

ekwb

ekwb EK-FC680 GTX SOC water block Leitfaden

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FC7970 Lightning Handbuch

ekwb

ekwb EK-Quantum Volume FLT Series Bedienungsanleitung

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Bedienungsanleitung

ekwb

ekwb EK-FB ASRock X399 RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC R9 Fury X Leitfaden

ekwb

ekwb EK-FC780 GTX HOF Series Handbuch

ekwb

ekwb EK-Backplate ASUS P6X58D Premium Leitfaden

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Bedienungsanleitung

ekwb

ekwb EK-FC7870 GTX Handbuch

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Bedienungsanleitung

ekwb

ekwb EK-FC285 GTX Classified Handbuch

ekwb

ekwb EK-FC670 GTX Backplate Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-Quantum Momentum ROG Zenith II Extreme Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken