Ekwb EK-FB EVGA CLASSIFIED 4-SLI Leitfaden

Installation and mounting manuals for EK-FB EVGA CLASSIFIED 4-SLI water block:

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION. Sam

icture of EVGA CLASSIFIED 4-SLI motherboard.

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws or plugs. All heat sink

assembly screws should be removed. There are 16 screws on the back of the

motherboard.

2. CLEANING THE PCB. Carefully detach the original heat sink after removing all

fasteners securing it to the board and bracket. Wipe off the remains (by using non–

abrasive cloth or qtip, as shown on sample photo) of the original thermal compound

until the components and circuit board are completely clean. EKWB does not

recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Southbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

3.a. APPLYING THERMAL COMPOUND.

4. CUTTING THERMAL PADS. Your block comes with three prepared thermal

pads, which have to be placed on chips. (PLEASE REMOVE FOIL OF THERMAL

PADS PRIOR TO INSTALLATION.WARNING DIMENSIONS BELLOW ARE

SCALED!)

Thermal pad #1 (thickness 0,5mm).

Cut thermal pad #2 (thickness 1,5mm) in a way you can cover 2 areas shown

on right picture.

Cut thermal pad #3 (thickness 1mm) lengthwise in half so you get two sized

90x7,5 mm.

EKWB made sure you have more than enough thermal pads to cover all areas

needed to provide best cooling performance.

5. PLACING THERMAL PADS

Applythermal

compoundhere.

Thermalpads#2

Thermalpad#1 Thermalpads#3

     Releasedon11thofNovember,2009.

213

STEP 2: PREPARING YOUR WATER BLOCK

6. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric. Thermal

paste provides enough adhesive force for standoffs to stay in a place.

USE OF STANDOFFS IS OBLIGATORY. FURTHERMORE, PLEASE DO NOT USE TOO MUCH TIGHTENING FORCE ON THE 2 SCREWS AROUND SOUTHBRIDGE.

ONLY IN THIS WAY THE POTENTIAL DAMAGE TO YOUR MOTHERBOARD IS AVOIDED.

(This notice is written upon the letter from EVGA RMA department. They state they will deny all RMA's if they find improper mounting method was used.)

STEP 3: ATTACHING WATER BLOCK TO MOTHERBOARD AND CHECKING FOR CONTACTS

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a sprin

mountin

system; therefore when attachin

be very careful to ti

hten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the board.

Use the enclosed screws and washers as shown in diagram below

Temporarily r

emove the water blocks to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 4: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA CLASSIFIED 4-SLI series are usually sold with high flow

fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always recommended

for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

VERY IMPORTANT NOTICE

Once the installation is completed, it is always a good idea to test the circuit for leaks, prior to powering up the computer. We recommend a 24 hour leak test

prior to powering up the computer. Do not test the water block directly from city water pressure. This will bow the top of the housing and render the block

unusable (and will void your warranty).

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 14 screws M2,5x6 DIN7985

M2,5x6

     Releasedon11thofNovember,2009.

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX JetStream Backplate Leitfaden

ekwb

ekwb EK-Vector Radeon VII Backplate Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC Titan Z Handbuch

ekwb

ekwb EK-Quantum Vector FE RTX 3090... Bedienungsanleitung

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-FB ASUS Max4 Extreme Leitfaden

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Bedienungsanleitung

ekwb

ekwb EK-XTOP Revo Dual D5 Serial Handbuch

ekwb

ekwb EK-Velocity sTR4 Bedienungsanleitung

ekwb

ekwb EK-TIM Indigo Extreme Bedienungsanleitung

ekwb

ekwb EK-FC285 GTX Classified Handbuch

ekwb

ekwb EK-FB ASUS M6E Leitfaden

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Bedienungsanleitung

ekwb

ekwb EK-FC1080 G1 GTX Backplate Leitfaden

ekwb

ekwb EK-FCW9000 Leitfaden

ekwb

ekwb EK-AIO 280 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Strix Handbuch

ekwb

ekwb EK-BAY DCP 2.2 Handbuch

ekwb

ekwb EK-Vector RTX 2080 Backplate Leitfaden

ekwb

ekwb EK-RES X3 D-RGB Bedienungsanleitung

ekwb

ekwb D-RGB Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB EVGA CLASSIFIED 4-SLI Leitfaden

Beliebte Computerhardware Handbücher anderer Marken