Elation EVLED256 Video Wall Bedienungsanleitung

EVLED256 Video Wall

Quick Start Guide

I. PC and Controller connections

1. Connect EVLED VSC controller to the graphics card on the PC with the included DVI cable. Connect EVLED VSC RJ11 port to the RS232

port on the PC with the included RS232 signal cable as pictured below. If your PC does not include RS232, use the included RS232 to

USB convertor.

2. On your PC, set up a secondary or clone display. A flashing green LED on the rear of the EVLED VSC indicates successful

communication.

One end of DVI cable connects with sending card in EVLED VSC controller

Connect theRS232 data cable into your PC (Use the RS232 to USB convertor if you

don’t have RS232 on your PC). Connect RJ11 end into the EVLED-VSC. The other end of DVI cable connects with PC graphic card

EVLED VSC Controller

ELATION

II. Power and data cable connection map. (Example map: 3 rows by 3 columns). This connection type is only recommended for up to 20

panels. When using more than 20 panels, an EVLED VDS data splitter should be used. Contact your Elation representative for a

custom connection map.

III. Application of Software

1. Launch LED Set software; click “Parameter” as pictured below.

Parameter

2. A password window will pop up as pictured below. Input password “168” and click “Ok”.

3. Sending card resolution set up: If your screen works in 1024×768 resolution mode, there is no need to select another display mode. If it does not,

click the “Display mode” drop down tab and select the correct displayresolution for your screen. Click “Save on sender” to confirm.

4. Installation of receiving card: Click “Receiver” tab. Window should display as pictured below.①Click “Load from files”→select

“EVLED256.RCG” ②Click “Send to receiver”→③Click “Save on receiver”.

Switch to “Receiver” setup screen

1. Load EVLED256.RCG panel profile 2. Send profile to receiver 3. Saving profile to sending card

(See next page for more info)

Select Profile (EVLED256.RCG)

5. Mapping and setup: (For example: to map 3 rows and 3 columns, setup should be as pictured below)

Update the quantity of screens if using more than one main screen→In “Type”, select “virtual pixel display”→set rows and columns for your

screen→select pixel points of each panel (The pixel points for each EVLED256 is 16x16)→set the map based on the signal connection (Ztype

connection as pictured below). Follow steps 1 – 9 in order. (1). Input number of screens

(2). Click “Update display QTY”

(3). Type: select “virtualpixel display” (4). Number of panels wide

(5). Number of panels high

(7). Signal connection:

(Front view data connection) (9). Save parameter to sending card.

(6). Input the number of pixel points for each panel. The EVLED256

Panel should be set as16 Width by 16 Height. (8). Send settings to sending card.

*NOTE: The EVELED VSC can control/drive up to 1280x1024 resolution. So if using EVLED256 panels, one (1) EVLED VSC controller

can drive a wall size of up to 80 panels wide by 64 panels high. Up to ten (10), EVLED256, panels can be connected into a single 20A

circuit.

6. Adjust play area start position: By default, the X/Y start position coordinates are 0 for X and 0 for Y. These coordinates place the play area in

the upper left corner of your PC monitor.

The X start point refers to the width of your monitor. The Y start point refers to the height of your monitor. Simply input the number of pixels that

you want the play area of your screen moved to then click “Set New”. For example, if I wanted to move my play area down 50 pixels, I’d input a

value of 50 into the “Start Y” box and click “Set New”. The play area will immediately move down and display whatever is currently in that area onto

your video wall.

Andere Handbücher für EVLED256 Video Wall

Andere Elation Beleuchtungsausrüstung Handbücher

Elation

Elation Design 60 Tri Bedienungsanleitung

Elation

Elation FUZE WASH Z120 Bedienungsanleitung

Elation

Elation EPAR TRI Bedienungsanleitung

Elation

Elation streamer Bedienungsanleitung

Elation

Elation VISION 575 Bedienungsanleitung

Elation

Elation High Output LED Color Changer Opti RGB Bedienungsanleitung

Elation

Elation ProColor Bedienungsanleitung

Elation

Elation PRO FS 15R FOLLOWSPOT Bedienungsanleitung

Elation

Elation KL Panel KLP001 Bedienungsanleitung

Elation

Elation KLF060 Bedienungsanleitung

Elation

Elation Design Spot 300E Bedienungsanleitung

Elation

Elation CMY Zoom 575E Bedienungsanleitung

Elation

Elation Level Q7 IP Bedienungsanleitung

Elation

Elation PROTEUS RAYZOR BLADES Bedienungsanleitung

Elation

Elation Event Par System Bedienungsanleitung

Elation

Elation CYBER PAK Bedienungsanleitung

Elation

Elation KL FRENSEL 6 Bedienungsanleitung

Elation

Elation Design LED 36MH Bedienungsanleitung

Elation

Elation CUEPIX PANEL Bedienungsanleitung

Elation

Elation FSH 1000 Bedienungsanleitung

Elation

Elation PLATINUM WASH ZFX PRO Bedienungsanleitung

Elation

Elation TVL3000WW Bedienungsanleitung

Elation

Elation Pro FS 575 Bedienungsanleitung

Elation

Elation UNI BAR Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung