Electro-Harmonix V256 Vocoder Bedienungsanleitung

V256

Vocoder

Congratulations on your purchase of the Electro-Harmonix V256 Vocoder. The V256 is a

versatile and easy to use vocoder with the added benefit of being in a compact pedal format.

Musicians no longer need large rack equipment, computer plugins, or large keyboards to get

a wide array of classic and modern vocoder sounds as well as a few very unique vocal

transposition effects. The V256 includes internal synthesizers for easy vocoding without an

external instrument.

Special Features of the V256:



3 VOX-ROBO vocoder modes that feature a robotic synthesizer



Single, Major, and Minor modes feature a drone synthesizer



3 Brand new vocal transposition modes including TRANSPOSITION, INSTRUMENT CTRL, and

REFLEX-TUNE



Vocoder bands adjustable from a vintage sounding 8 bands to a smooth sounding 256 bands



TONE, GENDER BENDER, and PITCH controls



Save and load up to 9 presets: 1 preset for each mode.



Scroll through the presets using the MODE knob or PRESET footswitch.



Built-In balanced Mic Pre-Amp with switchable Phantom Power and Gain adjustment.



Effect output on balanced XLR line output and 1/4” unbalanced instrument output

WARNING: Use only the AC Adapter that the V256 comes supplied

with. Do not use any other AC Adapters. Using other AC adapters,

even those made by Electro-Harmonix, could cause harm to the unit,

the adapter or you. The V256 does not use batteries.

- QUICK START GUIDE -

BASIC MIXER CONNECTION SETUP

1. Connect your microphone to the MIC input on the right side of the V256 using a

balanced XLR cable.

2. Using an unbalanced instrument cable, plug your instrument into the INST Input Jack on

the right side of the V256.

3. Connect a balanced XLR cable to the EFFECT output jack on the left side of the V256.

Connect the other end of the XLR cable to the line input of a mixer.

4. Connect an unbalanced instrument cable from the INST output jack on the left side of

the V256. Connect the other end of the instrument cable to the instrument input of a

mixer, or the input of an amplifier.

5. Plug the AC Adapter into a wall outlet.

6. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of the

V256.

Polarity is center negative

7. If using a condenser microphone, flip the Phantom Power switch up to the top position,

otherwise leave it off. The Phantom Power switch is located on the right side of the

V256, next to the XLR MIC input.

8. Push the MIC BYPASS footswitch until its associated LED is OFF. Sing into the

microphone, you will hear your dry vocal at this point. Adjust mixer settings as well as

the MIC GAIN switch on the V256 to obtain optimal mic levels.

BASIC AMPLIFIER CONNECTION SETUP

1. Connect your microphone to the MIC input on the right side of the V256 using a

balanced XLR cable.

2. Using an unbalanced instrument cable, plug your instrument into the INST Input Jack on

the right side of the V256.

3. Connect an unbalanced instrument cable from the INST output jack on the left side of

the V256. Connect the other end of the instrument cable to the input of a guitar, bass,

or keyboard amplifier.

4. Plug the AC Adapter into a wall outlet.

5. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of the

V256.

Polarity is center negative

6. If using a condenser microphone, flip the Phantom Power switch up to the top position,

otherwise leave it off. The Phantom Power switch is located on the right side of the

V256, next to the XLR MIC input.

7. Push the MIC BYPASS footswitch until its associated LED is OFF. Play the instrument,

you will hear only dry instrument signal at this point.

8. The factory setting for the INST output of the V256 is 100% dry instrument signal only.

In order to use the V256 in this mode the INST output blend needs to be adjusted.

9. Hold down the MIC BYPASS footswitch and adjust the BLEND knob. Fully CCW is 100%

instrument signal. As you turn the knob CW more V256 effect signal is added and at

noon, the mix of dry instrument to V256 effect will be even. As you continue to turn the

knob CW past noon, the dry instrument level will decrease and at fully CW the mix will

be 100% V256 effect.

10. After the BLEND knob is adjusted for the desired mix, release the MIC BYPASS

footswitch and the instrument output mix will be set. If the MIC BYPASS is not held

down, moving the blend knob will make no difference to the INST output mix.

BASIC VOCODER SETTINGS

1. Now that the V256 is hooked up and ready to go, here is a sample setting to get started.

2. Turn the MODE knob until the mode VOX-ROBO 1 is selected and set the other

parameters as follows:

-BLEND FULLY CW

-BANDS NOON

-TONE NOON

-GENDER NOON

-PITCH FULLY CW

3. Press and release the MIC BYPASS footswitch so that the effect is now ON and the LED

is lit.

4. Play the instrument and sing into the microphone at the same time. You will now hear

your voice modulating the sound of the carrier instrument.

5. To use the internal synthesizer, turn the PITCH knob to noon.

6. Sing into the microphone and you will hear your voice modulate the robotic synth.

7. These basic settings also apply to the single, major, and minor drone modes.

BASIC VOCAL TRANSPOSITION SETTINGS

1. Turn the MODE knob until the mode TRANSPOSITION is selected and set the other

parameters as follows:

-BLEND FULLY CW

-BANDS NOON

-TONE NOON

-GENDER NOON

-PITCH NOON

2. In this setting the vocal transposition will be at unity. Using the XLR output, turn BLEND

to noon for a subtle double tracking effect.

3. Adjust the GENDER BENDER knob to hear a more male or female version of your voice.

4. Turn the PITCH knob fully CW to hear 1 octave up, and fully CCW to hear 1 octave

down.

BASIC INSTRUMENT CONTROL SETTINGS

1. Turn the MODE knob until the mode INSTRUMENT CTRL is selected and set the other

parameters as follows:

-BLEND FULLY CW

-BANDS NOON

-TONE NOON

-GENDER NOON

-PITCH 2 O’CLOCK

2. Sing into the mic and you will hear your original vocal pitch. Play a single note line on

your instrument as you sing, you will hear your voice but the pitch will now track the

instrument’s notes.

3. Turn the BANDS knob to 2 o’clock and hear how your voice now slides to new notes as

you play your instrument.

BASIC VOCAL REFLEX-TUNE SETTINGS

1. Turn the MODE knob until the mode REFLEX-TUNE is selected and set the other

parameters as follows:

-BLEND FULLY CW

-BANDS NOON

-TONE NOON

-GENDER NOON

-PITCH FULLY CCW

2. Without playing an instrument sing into the mic. You will hear your pitch being hard

corrected to a chromatic scale.

3. Turn the BANDS knob fully CCW and sing into the mic. You will hear the pitch correction

happen much more gradually giving your vocal performance a more natural sound.

- DESCRIPTION OF MODES -

The V256 has 9 modes to choose from. Each mode gives the musician a different sonic

palette to work with. In addition, each mode may change the functionality of some of the

V256’s knobs. In this section we will describe each mode and the functionality of the knobs

that change with each mode.

Use the MODE knob to scroll through the 9 modes. Turning the MODE knob clockwise goes

up the LED ladder. Turning the MODE knob counter-clockwise goes down the LED ladder.

Below is a table displaying the function of each knob as it relates to a selected mode. Arrows

indicate the function that occurs as the knob is turned to or towards the extreme knob

position in that direction. The up arrows indicate the center position of the knob.

VOX-ROBO Modes

VOX-ROBO Modes 1, 2, and 3 are identical. This provides the flexibility to save 3 separate

ROBO presets. These modes function as standard vocoders using an external instrument as

the carrier signal, and in addition have robotic internal synthesizers that can be used as the

carrier signal and controlled with the PITCH knob. When the PITCH knob is fully CCW or fully

CW, the internal synthesizer is silenced. When the PITCH knob is at noon the robotic tone is a

C3 note. When the internal synthesizer is on, and an external instrument is played, they will

be mixed together and used as the carrier signal simultaneously.

You can “play” the internal synthesizer using a MIDI keyboard or sequencer.

DRONE Modes

The Drone modes have a more natural, musical sounding tone than the robotic modes. Just

as in the VOX-ROBO modes, the instrument input is always active as a source for the carrier

signal.

SINGLE DRONE –The single drone is a single pitch drone based on an organ sound. When

the PITCH knob is at noon, the pitch is a C3 note. The PITCH knob controls this note up to

+/-1octave. At fully CW or fully CCW, the drone is silenced.

MAJOR DRONE –The major drone is a three note major triad based on an organ sound.

When the PITCH knob is at noon, the chord is C4 major. The PITCH knob functions are the

same as in “SINGLE DRONE”.

MINOR DRONE –The minor drone is a three note minor triad based on an organ sound.

When the PITCH knob is at noon, the chord is an A4 minor. The PITCH knob functions are

the same as in “SINGLE DRONE”.

You can “play” the internal drone synthesizer using a MIDI keyboard or sequencer.

THE FREEZE FUNCTION

In any of the vocoder modes in the V256 when the MIC BYPASS footswitch is held down

while an instrument is being played, the V256 will freeze whatever is being played through

the INST input at the moment the MIC BYPASS button is pressed. The V256 will freeze this

sample for as long as the MIC BYPASS footswitch is held down. This frozen sample can also

be saved into a preset. Simply save the preset while the MIC BYPASS footswitch is held down

and the instrument sample is frozen.

When the preset is recalled, the frozen sample as well as any drones that were saved will be

recalled. In order to clear the saved frozen sample, hold the MIC BYPASS footswitch without

any instrument input, or turn the pitch knob to fully CCW. This will clear the frozen sample

however if the preset is reloaded the frozen sample will return. In order to clear the frozen

sample from the preset, turn the pitch knob fully CCW so the frozen sample stops playing,

then save a new preset in the current mode.

This feature can be used together with the internal synthesizers and can also be used to

freeze MIDI triggered notes.

VOCAL TRANSPOSITION MODES

TRANSPOSITION

In this mode the V256 does not require an external instrument. The V256 will transpose the

vocal signal by an amount determined by the PITCH knob. At noon the transposition is at

unity. At fully CW it is +1 octave and at fully CCW it is -1 octave.

The BANDS knob can be used to control how quickly the intervals change when controlled by

a MIDI input. At noon, the transposition interval will change instantaneously. As the knob is

moved CW the notes will change to new intervals more slowly creating a portamento type of

effect. As the knob is moved CCW the notes will change to new intervals more slowly, and

vocal pitch changes will also be delayed. Blended with the original vocal, this effect can be

used to add complexity to a double tracked vocal sound where the V256 effect sound will

reach new vocal pitches a little slower than they are sung.

A MIDI controller can control the amount of transposition. When two notes are played

together, the interval between those two notes will be applied to the transposition. When a

MIDI note is played, the setting of the PITCH knob will no longer be relevant and the original

vocal pitch will be heard. As a second note is played along with the first note, the interval

created will be applied to the vocal transposition. The MIDI notes being played are irrelevant,

only the interval matters. When the MIDI notes are released, the transposition will go back to

where the PITCH knob is set.

INSTRUMENT CTRL

In this mode the V256 will replace the vocal pitch with the pitch of an external instrument.

The PITCH knob controls the threshold of how loud the instrument must be in order for the

V256 to replace the vocal note. At fully CCW, the instrument has the least effect, and at fully

CW the V256 will never revert back to the dry vocal pitch. The pitch will remain at the last

instrument controlled note until a new note is played.

In this mode the BANDS knob controls how fast the pitch changes. At noon, the pitch will

change instantly. As the knob is turned CW the instrument controlled pitch will slide to new

notes more slowly. As the knob is turned CCW, the instrument controlled pitch changes will

slow in the same manner and in addition the original dry vocal notes will change more slowly.

When the external instrument falls below the threshold setting and the V256 reverts back to

the singer’s original vocal performance, as the singer changes pitch, notes will slide to one

another with a portamento effect.

A MIDI keyboard or sequencer can be used as the control instrument allowing you to play or

automate the notes you want to replace your vocal notes.

REFLEX-TUNE

In this mode the V256 works as an automatic pitch corrector and will quantize the dry vocal

pitch to nearest note depending on the scale and key set by the user. When the PITCH knob

is fully CCW, and there is no external instrument being played, the V256 will quantize to a

chromatic scale. If there is an external instrument being played, the V256 will determine the

key based on the chords being played and will quantize to the determined key in a diatonic

scale. To revert back to the chromatic scale, turn the PITCH knob to noon and back to fully

CCW. When the V256 is in chromatic mode, only the REFLEX-TUNE LED will be lit.

As the PITCH knob is turned CW, a different combination of LEDs will light depending on the

position of the PITCH knob. The combination of LEDs indicates the diatonic key scale setting

for the V256. The table in the “controls” section, under “PITCH” explains which keys are

represented by the LEDs.

The BANDS knob controls how fast the pitch changes from one quantized note to another.

Fully CCW is the slowest change and creates the most natural sounding performance. At noon

the quantized notes are changed instantaneously with no vibrato, creating the most dramatic

effect. At fully CW the note changes are still abrupt but more of the original vibrato is let

through.

- PRESETS -

The V256 can save one preset for each of the 9 modes. Each preset will pertain directly to the

mode you have saved it in. Once a preset is saved, the V256 will remember the preset after

power has been disconnected.

Saving a preset will save the setting of all 5 of the black knobs. The V256 will also save any

frozen samples that are created by holding the MIC BYPASS footswitch. You must hold down

the MIC BYPASS footswitch while saving the preset to save the frozen sound.

The V256 will not save the state of the MIC BYPASS footswitch, the MIC GAIN toggle switch

or the PHANTOM POWER toggle switch.

PRESET SAVE PROCEDURE:

1. To save the knob positions as they are currently set, press and hold down the MODE

knob.

2. Hold down the MODE knob for 3 seconds. Nothing will occur for 2 seconds, then all the

mode LEDs will blink for 1 second.

3. After the LEDs stop blinking, release the MODE knob. The PRESET LED will light up solid.

The PRESET LED is located to the left of the PRESET footswitch.

4. Your preset has been saved in the mode that is currently lit.

PRESET LOAD PROCEDURE:

USING THE MODE KNOB

1. To Load a preset you previously saved: turn the MODE knob to the mode where the

preset was saved.

2. Press and release the MODE knob. The PRESET LED will light up to indicate that the

preset has loaded. Please Note: The current knob positions are no longer valid.

USING THE PRESET FOOTSWITCH

1. To Load a preset you previously saved using the PRESET footswitch: press and release

the PRESET footswitch. The PRESET LED will light up to indicate that the preset has

loaded for the currently selected mode. Please Note: The current knob positions are no

longer valid.

2. If you press and release the PRESET Footswitch while a preset is already loaded into the

current mode, the V256 will jump down to the next mode and load its preset. For

example, if you have a preset loaded into VOX-ROBO 1 mode and press the PRESET

footswitch, the V256 will then select VOX-ROBO 2 as its current mode, with its preset

loaded.

After loading a preset, if you move a knob, the knob’s new location will supersede the

presets stored value for that knob. At this point, the PRESET LED will blink rapidly to

indicate that a knob has been moved. If you then turn the knob back to its position, as

saved in the preset, the PRESET LED will stop blinking.

If the PRESET LED is blinking rapidly, when you press the PRESET footswitch, it will re-

load the preset for whichever mode you are currently in.

PRESET UNLOAD PROCEDURE:

A preset can be unloaded to restore the current knob positions so they represent what you

hear. There are two ways to unload a preset, press and release the MODE knob or turn the

MODE knob to another mode. If a frozen sample is saved into a preset, it can be cleared by

holding the MIC BYPASS footswitch without playing the instrument, or by turning the PITCH

knob fully CCW. To erase the frozen sample permanently from the preset, the preset must

be saved again while the frozen sample is cleared.

- CONTROLS, INDICATORS & I/O-

BLEND

This knob sets the mix of dry vocal signal to V256 effect. Fully CCW is 100% dry, you will

hear only your dry vocals. Noon is an even mix of dry vocal and effect signal. Fully CW is

100% wet, you will only hear the V256 effect.

The BLEND knob also controls the mix of instrument signal to vocoder effect on the INST

output jack. To set the INST output mix hold down the MIC BYPASS footswitch and turn the

BLEND knob. Fully CCW will be 100% instrument signal or MIDI controlled internal

synthesizer. Noon will be an even mix of dry instrument and effect signal. Fully CW will be

100% effect signal. From the factory, the INST output jack is set for 100% dry signal. The

V256 will remember your last setting of the INST mix control through all modes. Each preset

can save a different setting.

BANDS

In all modes EXCEPT TRANSPOSITION, INSTRUMENT CTRL, and REFLEX-TUNE the BANDS

knob sets the number of bands for the vocoder. Fully CCW is 8 bands for a more lo-fi gritty

sound. Center position is 256 bands with no vocal resonance, for a smooth vocoder sound. As

the knob is turned CW from noon, the V256 will add filtered resonance from the vocal pitch

into the 256 bands. This adds complexity to the vocoder sounds as some bands are

accentuated by the vocal pitch.

Inhaltsverzeichnis

Andere Electro-Harmonix Musikpedal Handbücher

Electro-Harmonix

Electro-Harmonix STEREO POLYCHORUS XO Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix DELUXE ELECTRIC MISTRESS Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix METAL MUFF with TOP BOOST Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix HOLY GRAIL MAX Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix MOD 11 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix TURNIP GREENS Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Riddle: Q-Balls Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix TUBE EQ Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix DELUXE MEMORY MAN Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NANO POG Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix 1 ECHO Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Deluxe Bass Big Muff Pi Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Pitch Fork Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix STEREO MEMORY MAN WITH HAZARAI Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix B9 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix HOG GUITAR SYNTHESIZER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NANO POG Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix DELUXE MEMORY MAN 550-TT Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Grand Canyon Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Andy Summers Walking On The Moon Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix SLAMMI PLUS Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix GERMANIUM4 BIG MUFF PI Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Q-Tron Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix BASS CLONE Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Bedienungsanleitung

BYOC

BYOC Analog Chorus Handbuch

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung