Electro-Voice RE97LTx Bedienungsanleitung
Transducer: Condenser, Back-Electret
Freq. Response: 50 Hz - 15 kHz
Polar Pattern: Omnidirectional
Sensitivity, 1 kHz: -48 dBV, 4.0 mV/Pascal
Maximum SPL: >120 dB SPL
Equivalent Noise: 32 dBA
Dynamic Range: 88 dB
Output Impedance, 1 kHz: 3000 Ohms
Power Requirements: +5 VDC
Current Consumption: 310 μA
Polarity: Positive Pressure on Diaphragm
Produces a Positive Voltage on Pin 2
Dimensions: See Diagram
Cable: 4 ft (1.22 m) Long
0.052 in (1.30 mm) Diameter
TA4F Connector Wiring: Pin 1 - Ground
Pin 2 - Audio
Pin 3 - Bias Voltage
Pin 4 - Unused
Accessories Furnished: Long and Short Windscreens
Dual Clothing Clip
Gig Bag
Colors Available: Black, Beige
Net Microphone Weight: 10.5 g (0.4 oz)
Clip Only - 2.1 g (0.08 oz)
Optional Accessories: TXA Phantom Power Adapter
RE97LTx
Ultra-Miniature Condenser
Lapel Microphone
TA4F Connector
General Description: Technical Specifications:
Key Features:
Ultra-Miniature Size for Inconspicuous Use•
Omnidirectional Polar Pattern to Provide Clean •
Sound and Uniform Response
Lightweight, Low Profile, Rugged Construction•
Superior Sound Quality•
Terminated with Female TA4F Connector for •
use with any EV Wireless Bodypack Transmitter
Available in Black or Beige Finish•
The Electro-Voice® RE97LTx is an ultra-miniature,
omnidirectional, condenser microphone designed for
applications that demand a high quality microphone
element that is practically invisible when worn by
the speaker or performer. The RE97LTx is intended
for spoken-word use in theatrical performance, fixed
installations, corporate AV presentations, houses of
worship, or any venue where a full-range, natural, and
well-balanced sound is required from an inconspicu-
ous, lightweight microphone.
The output of the RE97LTx is clean and accurate, while
the omni-directional polar pattern ensures uniform
output regardless of the microphone’s angle relative
to the sound source. The provided clip is a convenient
anchor for the microphone on a lapel, tie, or shirt col-
lar.
The supplied windscreens can be utilized in windy
environments and to reduce breath noise. The RE97LTx
has a shielded 4ft cable terminated in a genuine
Switchcraft® TA4F connector and is ready for use
with standard EV and Telex body-pack transmitters
including the EV REV-BP, BPU-2/CSB-1000 and Telex
WT-500/WT-1000. The wire to the body-pack is ultra-
flexible, and may be easily concealed.
Frequency Response:
Windscreen Assembly:
Microphone Positioning:
Polar Response:
Product Dimensions:
The windscreen assembly is supplied with a plastic
adaptor to improve stability.
To apply: Hold the windscreen firmly at the “A” loca-
tions. Firmly press the microphone into the adaptor
until it stops.
NOTE: Use caution when removing the microphone
from the windscreen. Do not pull on product wire: grip
microphone by metal housing only.
Best results will be achieved with the microphone positioned 3 to 6 inches below the neckline. Typical locations
are on the lapel, shirt collar, or on the shirt directly below the chin. You should avoid covering the microphone with
any cloth or other material as this may change the frequency response characteristic of the microphone.
If mechanical noise from the cable is detected, it may be minimized by looping the cable up and through the dual
tie clip as shown in the picture on page 1, or by immobilizing the cable against the talker’s body.
Dimensions are in inches. Bracketed dimensions are millimeters.
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems 05/2010
Part Number LIT000165000 Rev D
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Electro-Voice®
Interfacing RE97L:
RE97LTx Part Numbers
F01U149502 RE97LTx Lapel Microphone, Beige Finish•
F01U149504 RE97LTx Lapel Microphone, Black Finish•
Your RE97LTx is configured for use with standard Electro-Voice and Telex bodypack transmitters. Modifications to
your RE97L should be performed by a qualified technician only. Using the microphone in a way other than de-
scribed in this manual may damage the microphone and void your warranty.
The following table is provided for your reference should you desire to utilize the RE97L with another manufac-
turer’s wireless transmitter bodypack. Always verify the specifications of your transmitter before attempting any
changes to your microphone.
Manufacturer Wireless Systems Connector Type Suggested Wiring
AKG WMS 40 Pro, WMS 400, and WMS4000
(Transmitters PT 40, PT400, and PT4000) TA3F
Pin 1: Shield
Pin 2: Wire
Jump Pin 2 to Pin 3
Audio-Technica
AT UniPak-type Transmitters ATW-1127, ATW-1235, ATW-1451,
ATW-2110, ATW-3110a, AEW-T1000, ATW-201, ATW-601,
ESW-T210, and ESW-T211 for the following systems: 1100,
1200, 1400, 2000, 3000, 4000, and 5000 Series Professional;
200 and 600 Series Freeway; NOT for use with U100 System
Hirose 4-Pin
HR10A-7P-4S
Pin 1: Shield
Jump Pin 1 to Pin 2
Pin 3: Wire
Shunt Pins 3-4 with R = 5k Ohms
Electro-Voice RE-2 (BPU-2); RE-1 (CSB-1000); R100 (BPV) TA4F
Pin 1: Shield
Pin 2: Wire
Shunt Pins 2-3 with R = 10k Ohms
Pin 4: Not Connected
Sennheiser Evolution Wireless Systems 100, 300, 500
(Transmitters SK100, SK300, SK500), and G2 Series
3.5mm (1/8”)
Stereo or Mono
Mini-Plug
Tip: Wire
Sleeve: Shield
Ring: Not Connected
5V Zener diode: + to tip, - to sleeve
(1N5231 or similar)
Shure
Performance Gear (UT1); PGX1; SLX1; T Series (T1, T11);
UC1; UHF (U1); UHF-R (UR1); ULX Professional and
ULX Standard (ULX1)
TA4F
Pin 1: Shield
Shunt Pins 2-3 with R = 10k Ohms
Pin 3: Wire
Pin 4: Not Connected
Telex FMR Series 70, 500, 1000 (Transmitters WT-55, WT-500,
WT-1000); SAFE 1000 (SAFE WT) TA4F
Pin 1: Shield
Pin 2: Wire
Shunt Pins 2-3 with R = 10k Ohms
Pin 4: Not Connected
Inhaltsverzeichnis
Andere Electro-Voice Mikrofon Handbücher
Electro-Voice
Electro-Voice RE10 Bedienungsanleitung
Electro-Voice
Electro-Voice N/D357 Bedienungsanleitung
Electro-Voice
Electro-Voice 625TRSKK Dimensionsleitfaden
Electro-Voice
Electro-Voice N/D468 Bedienungsanleitung
Electro-Voice
Electro-Voice RE34 Bedienungsanleitung
Electro-Voice
Electro-Voice 408 Bedienungsanleitung
Electro-Voice
Electro-Voice RE50/B Bedienungsanleitung
Electro-Voice
Electro-Voice N767a Bedienungsanleitung
Electro-Voice
Electro-Voice ENG 618 Bedienungsanleitung
Electro-Voice
Electro-Voice N/D478 Bedienungsanleitung
Electro-Voice
Electro-Voice RE16 Bedienungsanleitung
Electro-Voice
Electro-Voice N/D Series II 308A Bedienungsanleitung
Electro-Voice
Electro-Voice CO100 Bedienungsanleitung
Electro-Voice
Electro-Voice 635L Bedienungsanleitung
Electro-Voice
Electro-Voice PL80a Bedienungsanleitung
Electro-Voice
Electro-Voice US658H Bedienungsanleitung
Electro-Voice
Electro-Voice Press-to-talk 619 Bedienungsanleitung
Electro-Voice
Electro-Voice HM2 Bedienungsanleitung
Electro-Voice
Electro-Voice N868 Bedienungsanleitung
Electro-Voice
Electro-Voice PC Sat-5 Bedienungsanleitung
Beliebte Mikrofon Handbücher anderer Marken
IK Multimedia
IK Multimedia iRig Stream MIC PRO Bedienungsanleitung
DAPAudio
DAPAudio RM-101 Bedienungsanleitung
AKG
AKG CHM 21 Bedienungsanleitung
Sennheiser
Sennheiser evolution wireless series EM 100 Bedienungsanleitung
Sony
Sony C-48 Bedienungsanleitung
GIGAMEDIA
GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung
