Electrolux Z4009 Bedienungsanleitung

Z4009

75 Tornado Vacuum Cleaner

Operating Instructions

Line drawings are solely for illustration purposes and are subject to variations from actual product.

1. Mains cable

2. Cable rewind button

3. On/off button

4. Variable suction control

5. Dust container

6. Filter indicator

7. Hose assembly

8. Carrying handle

9. Telescopic tube

10. Hose handle with

air valve control

11. Combination carpet/

hard ﬂoor nozzle

12. Upholstery nozzle,

Crevice nozzle and

Dusting brush

Dear Customers,

Please read through these operating

instructions carefully. Above all please

observe the safety instructions on the

ﬁrst few pages of these operating

instructions! Please keep these

operating instructions for later reference.

Pass them on to any subsequent owner

of the appliance.

Important Safety

Instructions

READ ALL INSTRUCTIONS

BEFORE USING (THIS APPLIANCE)

When using an electrical appliance

basic precautions should always be

followed, including the following. Before

connecting the cleaner to an electrical

supply outlet, ensure that the voltage

marked on the rating plate (on the

underside of the cleaner) is correct for

your electrical supply. If it does not

comply, do not use the cleaner prior to

contacting the manufacturer.

WARNING – To reduce the risk of ﬁre,

electric shock, or injury:

1. Do not leave vacuum cleaner when

plugged in. Unplug from outlet when

not in use and before servicing.

2. To reduce the risk of electric shock,

do not use outdoors or on wet

surfaces.

3. Young children should be supervised

to ensure that they do not play with

the appliance. Close attention is

necessary when used near children.

4. This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by

a person responsible for their safety

Children should be supervised to

ensure that they do not play with the

appliance.

5. Use only as described in this

manual. Use only manufactures

recommended attachments.

6. Do not use with damaged cord or

plug. If vacuum cleaner is not

working as it should, has been

dropped, damaged, left outdoors,

or dropped in water, enter it to a

service centre before using.

7. Do not pull or carry on cord, use as

a handle.

Do not close door on cord, or pull

around sharp edges or corners. Do

not run vacuum cleaner over cord.

Keep cord away from heated

surfaces.

8. Do not unplug by pulling on the cord.

To unplug, grasp the plug, not the

cord.

9. Do not handle the plug or vacuum

cleaner with wet hands.

10. Do not put any object into openings.

Do not use with any opening

blocked.

Keep free of dust, lint, hair and

anything that may reduce airﬂow.

11. Keep hair, loose clothing, ﬁngers and

all parts of body away from openings

and moving parts.

12. Turn all controls off before

unplugging.

13. Use extra care when cleaning on

stairs.

14. Do not use to pick up ﬂammable or

combustible liquids, such as

gasoline, or use in areas where they

may be present.

15. Unplug before connecting the hose.

16. Do not pick up anything that is

burning or smoking, such as

cigarettes, matches, or hot ashes.

17. Do not use without dust bag and/or

ﬁlter in place.

18. Do not use extension cords or

outlets with inadequate current

carrying capacity.

19. We recommend you do not use

your vacuum on carpet cleaning

foams, sharp or heavy building

materials or plaster dust. They

could damage or clog dustbag and

cause failures to other key parts

in your vacuum cleaner and render

your warranty invalid.

20. Store your cleaner indoors in a cool,

dry area.

21. Keep your work area well lighted.

22. Unplug electrical appliances before

vacuuming them.

Customer

Information

Electrolux decline all responsibility for all

damages arising from improper use of

the appliance, or in cases where there

has been tampering with the appliance

other that by an Authorised Electrolux

service agent. This appliance has

been designed with the environment in

mind and all plastic parts are marked

accordingly for recycling purposes.

For your closest service agent for

servicing or to obtain accessories for

your vacuum cleaner, please contact our

customer service help line noted on back

cover of this booklet.

The symbol on the product or on its

packaging indicates that this product

may not be treated as household

waste. Instead it shall be handed over

to the applicable collection point for

the recycling of electrical and electronic

equipment. By ensuring this product

is disposed of correctly, you will help

prevent potential negative consequences

for the environment and human health,

which could otherwise be caused by

inappropriate waste handling of this

product. For more detailed information

about recycling of this product, please

contact your local city ofﬁce, your

household waste disposal service or the

shop where you purchased the product.

Service & Repair

It is dangerous to alter the speciﬁcations

or modify the product in any way. Under

no circumstances should you attempt to

repair the cleaner yourself.

NB! To avoid injury and prevent damage

to the vacuum cleaner a defective cord

must only be replaced by an authorised

service provider approved by the

manufacturer to avoid a hazard. The

vacuum cleaner should be serviced by

an authorised service provider and only

genuine.

WARNING: On collection of proprietary

carpet conditioning powder, it is

recommended that the dust container

is emptied and the cartridge ﬁlter is

cleaned after each use. Some of the

preparations contain substances

which while left in the vacuum cleaner

for extended periods, could cause

damage. Many air fresheners, household

deodorants, sprays and polishes contain

highly inﬂammable gas propellants,

because of this it is particularly

important that these products are used

strictly in accordance with the relevant

manufacturers instructions, it is essential

that none of the above products are

sprayed directly into the vacuum cleaner

or any of the ﬁlters, hose assembly or

dust chamber.

Filter indicator: before commencing

cleaning, plug the cleaner in and turn

it on (without the hose attached to the

cleaner).

If the indicator is red, clean the ﬁlter.

If the indicator is clear, attach the hose

and all the other necessary attachments

and commence cleaning.

5. Press the On/Off button to activate

the cleaner.

6. By moving the variable power

control, the suction power can be

adjusted.

7. You may adjust the air valve on

the handle.

GETTING THE BEST RESULTS

Carpets: Use the ﬂoor nozzle with the

lever in horizontal position.

Hard Floors: Use the ﬂoor nozzle with

the lever in vertical position.

Loose rugs/curtains/light weight

fabrics: Reduce the suction power. Use

the ﬂoor nozzle for loose rugs and the

upholstery nozzle for curtains, cushions,

fabrics, etc.

Assembling The

Vacuum Cleaner

GETTING STARTED

1. Check the dust container is in place.

2. To connect the hose into the suction

inlet push it until it clicks.

To disconnect the hose form the

suction inlet, push the button at the

end of the hose.

3. Attach the telescopic tube to the

hose handle and ﬂoor nozzle by

pushing and twisting together. (Twist

and pull apart to dismantle).

4. Extend the cable and connect to the

mains. The cleaner is ﬁtted with cord

rewind, ensure cord is not twisted

before use. (Press foot pedal to

rewind. Note: Please hold the plug to

prevent it striking you or the

machine).

Conﬁned areas: Use the crevice nozzle

for crevices, corners and radiators.

Dusting brush - Use for removal of

dust coverage on furniture and slatted

blinds.

REMOVING THE CONTENTS OF THE

DUST CONTAINER

Always operate the cleaner with the dust

container installed.

1. Remove the dust container by lifting

the handle on top of the container.

2. Remove the contents of the dust

container by pushing the orange-

coloured opening button.

3. Close the dust container lid until it

clicks.

4. Put the dust container back into the

cleaner.

5. Lock the dust container in place

by pushing down on the handle until

it clicks into place.

REMOVAL, CLEANING AND FITTING

THE PLASTIC CONE ASSEMBLY

To ensure there is no restriction of air

ﬂow resulting in loss of suction after

the emptying of the dust container, it is

essential that the plastic cone is checked

for blockages.

REMOVAL OF THE PLASTIC

CONE SECTION

1. Place the dust container upside

down with the HEPA ﬁlter facing

away from you.

2. Open the dust compartment cover

ﬂap by pressing the ﬂap release

button.

3. The plastic cone assembly is located

on the left hand side. Twist the cone

assembly anti clockwise and lift out

the one assembly.

4. Check for residue build up,

if present, wipe clean and replace the

cone assembly in the locking position

in the dust container. Turn clockwise

to lock it in position (please note that

the cone assembly can only be ﬁtted

one way.)

5. Close the ﬂap and install the dust

container in the vacuum cleaner

body, ensuring it is locked into

position.

Please note: It is normal for the dust

container full indicator to ﬂicker ON and

OFF during use. If the dust container

is emptied and the indicator is still

ﬂickering, this indicates the HEPA ﬁlter

and frame is clogged. In this case follow

the instructions replacing or cleaning the

HEPA ﬁlter and frame.

CLEANING THE EXHAUST FILTER

Open the ﬁlter grill to remove the exhaust

ﬁlter.

Take the ﬁlter out of the grill and insert a

new one. Close the ﬁlter grill.

REPLACING AND CLEANING

THE PROTECTION FILTER AND

HEPA FILTER

1. Remove the dust container by lifting

the handle on top of the container.

2. a. There are two pre- motor ﬁlters

in this vacuum cleaner, a spongy

grey protection ﬁlter, and the

framed HEPA ﬁlter.

b. Remove the HEPA ﬁlter frame

from the container by pulling

on the release tab on the top

right side of the ﬁlter frame.

Remove the grey protection

ﬁlter by simply pulling it loose

from the container.

c. Tap the HEPA ﬁlter face down

on a ﬂat surface covered with

a sheet of paper. This will

dislodge excessive residue from

the HEPA ﬁlter. Dispose of the

cover sheet with the dust residue.

Gently beat the grey protection

ﬁlter in an open air space to

properly dislodge any dust.

3. If necessary both the HEPA ﬁlter

and grey protection ﬁlter can be

washed under a tap with cold

water. Always wash the ﬁlter from the

underside, do not scrub of use

cleaning agents on the ﬁlter.

4. Air dry both the HEPA ﬁlter and grey

protection ﬁlter for 24 hours to

ensure it is completely dry before

reusing. Avoid direct sunlight or

extreme drying conditions.

5. a. Reﬁt the grey protection ﬁlter

by aligning it with the dust

container and sitting it in place,

then ﬁt the HEPA ﬁlter by aligning

the frame with the dust container

and simply sliding the HEPA ﬁlter

into place.

b. When ﬁtted correctly the tab in

the top right corner of the frame

should depress a black safety

tab, allowing the dust container

to ﬁt back into the vacuum

cleaner.

6. If either of the ﬁlters appear damaged

do not re use them.

Trouble Shooting And

Customer Information

The vacuum cleaner does not start

1. Check that the power cord is

connected to the mains.

2. Check that the plug and power cord

are not damaged.

3. Check for a faulty/blown fuse.

The vacuum cleaner stops

1. Check whether the dust container is

full. If so, empty it.

2. Is the nozzle, tube or hose blocked.

3. Are the ﬁlters blocked.

Water has entered the vacuum

cleaner

It will be necessary for the Fan Unit /

Motor to be replaced by an Authorised

Electrolux service agent. Damage to

the Fan Unit / Motor caused by the

penetration of water is not covered by

warranty.

Technical Data

Rated Voltage: 220 – 240V, 50/60Hz

Max Power (W): 2000W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Staubsauger Handbücher

Electrolux

Electrolux OXYGEN classic Bedienungsanleitung

Electrolux

Electrolux ZAC 6805 accelerator Bedienungsanleitung

Electrolux

Electrolux Ultraactive Bedienungsanleitung

Electrolux

Electrolux EL7000A Bedienungsanleitung

Electrolux

Electrolux PC91-4RR Bedienungsanleitung

Electrolux

Electrolux Z400 Series Bedienungsanleitung

Electrolux

Electrolux ZO 6352 Bedienungsanleitung

Electrolux

Electrolux Classic Silence Bedienungsanleitung

Electrolux

Electrolux ZB 260 Bedienungsanleitung

Electrolux

Electrolux UltraOneMini Bedienungsanleitung

Electrolux

Electrolux ergospace XXLTT14 Bedienungsanleitung

Electrolux

Electrolux iCute Z209 Bedienungsanleitung

Electrolux

Electrolux ERGORAPIDO Bedienungsanleitung

Electrolux

Electrolux UltraActive ZUA 3830P Bedienungsanleitung

Electrolux

Electrolux ultracaptic Bedienungsanleitung

Electrolux

Electrolux ZB 2901 Bedienungsanleitung

Electrolux

Electrolux Ergorapido EERC75WRK Bedienungsanleitung

Electrolux

Electrolux mobione ZMO1520 Bedienungsanleitung

Electrolux

Electrolux Versatility All Floors EL4060A Bedienungsanleitung

Electrolux

Electrolux Praxio Z 6035 Bedienungsanleitung

Electrolux

Electrolux Oxygen3 EL5020 Bedienungsanleitung

Electrolux

Electrolux UltraDynamica EUEL75IGM Bedienungsanleitung

Electrolux

Electrolux ZSC 6920 Bedienungsanleitung

Electrolux

Electrolux Oxygen EL6988A Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung