Electrolux Z7292 Bedienungsanleitung

Sugar & Salt Ltd.

Cyan

M agenta

YellowBlack Page: 1

Sugar & SatLtd.

Cyan

M agenta

YellowBlack Page: 2

Thank you for choosing an Electrolux Cyclone Power vacu-

um cleaner. These operating instructions cover all Cyclone

Power models. This means that with your specific model,

some accessories may not be included.

Accessories and safety precautions 3

Before starting 4

Getting the best results 4

Removing the contents of the dust container 5

Cleaning the cartridge filter 5

Cleaning the motor filters and the micro exhaust filter 6

Cleaning the hose and nozzle 7

Troubleshooting and customer information 8

Electrical supply instructions 9

WARNING instructions 10

Guarantee 11

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 2

ACCESSORIES AND SAFETY PRECAUTIONS

Accessories

1. Cartridge filter

2. Plastic extension tube (Z7211)

3. Metal extension tubes (Z7292)

4. Hose

5. Hose handle with suction control

6. Dual purpose floor nozzle

7. Upholstery nozzle

8. Crevice nozzle (Z7292)

Safety precautions

The Cyclone Power should only be used by adults for nor-

mal vacuuming in a domestic environment. The vacuum

cleaner features double insulation and does not need to be

earthed.

Never vacuum:

• In wet areas

• Close to flammable gas, etc.

• Without filters (this may damage the cleaner). A safety

device is fitted which prevents the dust container closing

without a cartridge filter in place. Do not attempt to force

the dust container shut.

Never vacuum:

• Sharp objects

• Fluids (this can cause serious damage to the machine)

• Hot or cold cinders, lit cigarette butts, etc.

• Fine dust from plaster, concrete, flour or ash, for example.

The above can cause serious damage to the motor - dam-

age which is not covered by the warranty.

Electrical cable precautions:

• A damaged cable must be replaced by an authorised

Electrolux service engineer. Damage to the cleaner cable

will not be covered by the warranty.

• Never pull or lift the vacuum cleaner by the cable.

• Disconnect the plug from the mains before cleaning or

maintenance of the vacuum cleaner.

• Regularly check that the cable is not damaged. Never use

the vacuum cleaner if the cable is damaged.

All service and repairs must be carried out by an authorised

Electrolux service engineer. Always keep the vacuum cleaner

in a dry place.

123

678

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 3

BEFORE STARTING

1. Always operate the cleaner with the dust container

installed.

2. Always operate the cleaner with the filter set property

installed.

3. Insert the hose until the catch clicks to engage (press the

catch to engage hose).

4. Attach the plastic tubes (Z7211) or metal tubes (Z7292) to

the hose handle and the floor nozzle.

5. Pull out the cable and plug it in.

6. Press the foot pedal to rewind the cable (take hold of the

plug to prevent it striking you).

7. Press the On/Off button to start the vacuum cleaner.

Adjust the suction power by using the linear suction con-

trol or the suction control on the hose handle.

GETTING THE BEST RESULTS

Hard floors: Use the dual purpose floor nozzle with the left

pedal in position (8.)

Carpets: Use the dual purpose floor nozzle with the

left pedal in position (9.)

Reduce suction power for rugs and fabrics.

Upholstered furniture: Use the upholstery nozzle.

Skirting boards, crevices, corners, etc.: Use the crevice

nozzle.

For the perfect care of your carpets: use the turbo nozzle.

The rotary motion of its brush gently loosens short-pile car-

pets where the dirt has been trodden in. It removes stubborn

fluff and pet hairs.

123

456

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 4

REMOVING THE CONTENTS OF THE DUST CONTAINER

Never operate the cleaner without the dust container installed.

The dust container must be emptied if the window of the dust

container indicator is red when the cleaner is operating at max-

imum power and the nozzle is raised from the floor.

Never open the top cover with the hose connected to the cleaner.

1. Open the top cover.

2. Remove the dust container from the cleaner.

3. Remove the filter set from the dust container by taking it

in the way indicated

4. Remove the contents of the dust container.

3. Put the filter set back into the dust container.

2. Put the dust container back into the cleaner.

1. Close the top cover.

Note: Empty the dust container even if it is not full (the filters may be

blocked). Also replace after using carpet-cleaning powder.

CLEANING THE FILTERS

Filters should be cleaned regularly and replaced twice a year.

Disconnect from electrical outlet before cleaning filters.

Your cleaner is fitted with a dust container indicator. Before

commencing cleaning, without the hose attached, check the

dust container indicator.

If red, clean or replace filter, if not, attach the hose, extension

tubes and accessories as normal and continue cleaning.

NB: It is normal for the indicator to be red during cleaning.

Cleaning the cartridge filter

Always operate the cleaner with the cartridge filter installed.

1. Open the top cover.

2. Remove the dust container from the cleaner.

3. Remove the filter set from the dust container by taking it

as indicated.

5. Remove the cartridge filter by turning it counter-clock-

wise (A) and pull it out (B) as indicated.

6. Rinse it under tap water.

7. Air dry for approximately 24 hours, to ensure it is com-

pletely dry before re-using. Avoid direct sunlight and

extreme drying circumstances (hair-dryer, etc.).

If you wish to use your appliance while the cartridge filter

is drying, you may use the extra cartridge filter inserted in

the packaging box.

5. Insert the cartridge filter into its place (B) and turn it

clockwise (A) as indicated in the icon.

3. Put the filter set back into the dust container.

2. Put the dust container back into the cleaner.

1. Close the top cover.

123

456

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 5

Cleaning the motor filters

Motorfilter ‘A’

1. Open the top cover.

2. Remove the dust container from the cleaner.

3. Remove the filter set from the dust container by taking it

as indicated in the icon.

4. Remove the cartridge filter by turning it counter-clock-

wise (A) and pull it out (B) as indicated in the icon.

5. Remove the filter from its place.

6. Rinse it under tap water and dry it completely.

5. Put the filter back into its place.

4. Insert the cartridge filter into its place (B) and turn it

clockwise (A) as indicated in the icon.

3. Put the filter set back into the dust container.

2. Put the dust container back into the cleaner.

1. Close the top cover.

Motorfilter reference number: EF76

Motorfilter ‘B’

1. Open the top cover.

7. Remove the filter from its place.

6. Rinse it under tap water and dry it completely.

7. Put the filter back into its place.

1. Close the top cover.

Motorfilter reference number: EF1

Cleaning the micro exhaust filter

8. Open the filter grill to remove the exhaust filter.

9. Take the filter out of the grill.

6. Rinse it under tap water and dry it completely.

9. Put the filter back into the grill.

8. Close the filter grill.

Micro exhaust filter reference number: EF2

Note: Do not use cleaning agents and avoid touching the

delicate filter

surface.

123

456

789

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 6

CLEANING THE HOSE AND NOZZLE

The vacuum cleaner stops automatically if the nozzle, tube

or hose becomes blocked, or the filters are blocked.

Disconnect from the mains and allow the vacuum cleaner to

cool down for approximately 20-30 minutes. Clear whatever

is causing the blockage and/or replace dirty filters.Then

restart the vacuum cleaner.

Tubes and hose

1. Use a cleaning strip or similiar to clear the tubes and

hose.

2. It is sometimes possible to clear the hose by "massag-

ing" it. However, be careful in case the obstruction has

been caused by glass or needles caught inside the hose.

Note: The warranty does not cover any damage to hoses

caused by cleaning them.

Cleaning the floor nozzle

3. To avoid reduction in suction power, frequently clean the

dual purpose floor nozzle. The easiest way to clean it is

by using the hose handle.

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 7

TROUBLESHOOTING AND CUSTOMER INFORMATION

Troubleshooting

The vacuum cleaner does not start

1. Check that the cable is connected to the mains.

2. Check that the plug and the cable are not damaged.

3. Check for a blown fuse.

The vacuum cleaner stops

1. Check whether the dust container is full. If so, empty it.

2. Is the nozzle, tube or hose blocked?

3. Are the filters blocked?

Water has entered the vacuum cleaner

It will be necessary to replace the motor by an authorised

Electrolux service engineer.

Damage to the motor caused by the penetration of water is

not covered by the warranty.

Customer Information

Electrolux decline all responsibility for all damages arising

from any improper use of the appliance or in cases of tam-

pering with the appliance. This product is designed with the

environment in mind. All plastic parts are marked for recy-

cling purposes.

For further details see our website: www.electrolux.com

For repairs or accessories, contact the Electrolux Group

Floorcare Helpline on 08706 055 055.

If you have any comments on the cleaner or the

Instructions for Use booklet please contact us on: 08706

055 055

The symbol on the product or on its packaging indicates

that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection

point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inap-

propriate waste handling of this product. For more detailed

information about recycling of this product, please contact

your local city office, your household waste disposal service or

the shop where you purchased the product.

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 8

Before you start …check

the voltage

Before connecting the

cleaner to an electrical sup-

ply ensure that voltage

marked on the data plate

(on the underside of clean-

er) is correct for your elec-

trical supply. If is not, do

not use the cleaner but

refer back to your dealer.

Connecting to your electrical supply

Permanently connected to the cleaner is a mains supply (2-core)

cable fitted with a non-rewirable plug incorporating a 13A fuse. In

the event of the fuse requiring replacement the fuse cover should

be removed using a small screwdriver. The old fuse MUST be

replaced by a 13A ASTA approved BS1362 fuse and the fuse cover

must be replaced before the plus is used again. In the event of loss

of the fuse cover, replacements can be obtained from your

Electrolux dealer or Electricity Board and must be of the same

colour as indicated by the coloured insert on the base plug.

If difficulty is experienced in obtaining a replacement, contact your

nearest Electrolux Service Centre. (Please see the separate

Electrolux Service Organisation leaflet).

In no circumstances must the plug be used without a correct

fuse cover fitted.

If the plug that is fitted to your appliance is not suitable for your

socket outlet, it must be cut off and the appropriate plug fitted.

Remove the fuse from the cut off plug. The cut off plug should then

be disposed of to prevent hazard of shocks in case it should be

plugged into a 13 Amp socket in another part of your home

The wires in the mains cable of this appliance are coloured in

accordance with the following code:

Blue: Neutral.

Brown: Live.

As the colours of the wires in the mains cable of this appliance may

not correspond with the coloured markings identifying the termi-

nals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal

which marked with the letter N or coloured black. The wire which is

coloured brown must be connected to the terminal which is marked

the letter L or coloured red.

If using a three-pin plug, do not make any connection to the termi-

nal marked with the letter E or by the earth symbol or coloured

green or green-and-yellow. This cleaner is double insulated and no

earth-connection is necessary.]

It is in you interest to ensure that the plug is correctly attached to

the mains cable. In case of doubt, have it done by a qualified elec-

trician, as Electrolux cannot regard the repair of faults on the plug

connection as a service that can be given free of charge under the

terms of guarantee.

As a general guide to fitting any plug

• Ensure the lengths of wire inside the plug are prepared correctly.

• Connection should be firmly made after all conductor stands are

entered into the terminal posts.

• When preparing the cable ends take care not to damage the outer

seal, or insulation surrounding the inner conductors.

• Tighten all screws.

• Replace the top cover of the plug and secure.

ELECTRICAL SUPPLY INSTRUCTIONS

z72xx_ifu_inside.qxp 2006.02.20. 17:08 Page 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Staubsauger Handbücher

Electrolux

Electrolux EL8502 Bedienungsanleitung

Electrolux

Electrolux Ergorapido Green Bedienungsanleitung

Electrolux

Electrolux Ultra Silence Bedienungsanleitung

Electrolux

Electrolux CANISTER Bedienungsanleitung

Electrolux

Electrolux UltraActive EL4307A Bedienungsanleitung

Electrolux

Electrolux ZUFCLASSIC Bedienungsanleitung

Electrolux

Electrolux EL5010 - Aptitude Quiet Upright Vacuum... Bedienungsanleitung

Electrolux

Electrolux Rapido ZB4112 Bedienungsanleitung

Electrolux

Electrolux Loopie Z2950 Series Bedienungsanleitung

Electrolux

Electrolux Trilobit ZA1 Bedienungsanleitung

Electrolux

Electrolux ClassicSilencer Bedienungsanleitung

Electrolux

Electrolux UltraActive Turbo EL4325A Bedienungsanleitung

Electrolux

Electrolux Classic Silence ZCS2000 Bedienungsanleitung

Electrolux

Electrolux Access Bedienungsanleitung

Electrolux

Electrolux AEG 60 Series Bedienungsanleitung

Electrolux

Electrolux Beam Alliance Bedienungsanleitung

Electrolux

Electrolux Rapido ZB 3103 Bedienungsanleitung

Electrolux

Electrolux Rapido Plus Bedienungsanleitung

Electrolux

Electrolux ergospace XXLTT14 Bedienungsanleitung

Electrolux

Electrolux Loopie Z2950 Series Bedienungsanleitung

Electrolux

Electrolux Z5600 Series Bedienungsanleitung

Electrolux

Electrolux vivaquickstop Bedienungsanleitung

Electrolux

Electrolux Z2920 Series Bedienungsanleitung

Electrolux

Electrolux TWINCLEAN Z 8234 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung