Elite Screens CineTension2 Series Bedienungsanleitung

www.elitescreens.com / eliteinfo@elitescreens.com

SCREENS

Elite

SCREENS

Tension2 Electric Screen

CineTension2 Series

Users Guide

Rev. 1.1

www.elitescreens.com / eliteinfo@elitescreens.com

Elite SCREENS

Important Safety and Warning Precautions:

1. Be sure to read this manual before use and follow the procedures as specified:

Put this manual in a safe place where it can be easily obtained for future reference.

To avoid possible product damage, do not use the accessories not recommended by the manufacturer.

Handle the device carefully during transportation and installation.

Do not set up the screen on an uneven or inclined location.

Do not set any heavy objects on the power cord and arrange it properly to avoid it becoming a trip hazard.

To prevent electrical shock or fire, do not overload the power cord.

Do not allow any liquids or moisture into the electric mechanism. Never handle any electrical devices if you

are wet or in direct contact with any other water source.

2. Always disconnect the power when replacing any accessories in order to avoid risks of a short circuit or an

electric shock.

3 There are no user serviceable accessories in the device. Only an authorized Elite Screens technician is

permitted to open the product casing and work on the internal parts. Failure to do so will void the warranty.

(User Tip) Make sure that the product voltage connection is compatible with the power source outlet. The

rating label on the product indicates the voltage rating.

(Environmental Tip.) In compliance with EPA regulations, please utilize the appropriate facility when in

need of product disposal at the end of its operational lifetime.

4. Do not use this product under the following circumstances:

1)During a heavy storm, wind, rain, thunder or lightning.

2) To ensure a maximum product life, avoid direct sunshine, water or moisture.

3) Keep away from fire sources and high temperatures to prevent overheating.

4) Disconnect the power supply first before transportation or maintenance.

www.elitescreens.com / eliteinfo@elitescreens.com

SCREENS

Optional

12V

Trigge

12V trigger for your new Elite CineTension allows your

screen to synchronize its drop and rise with the

projector's power cycle. The screen Drops when the

projector powers up and retracts when the projector

powers down.

2. IR

(Infrared)

Wall Box

Kit

and Eye Receiver:

The Wall Box Kit contains an IR receiver and

enables the consumer to use either the IR remote or hardwire controls to operate the screen's drop/rise capabilities.

The IR Eye protrudes from the bottom of the casing to present a low profile line-of-sight control option for your IR

remote.

It is a low-visibility alternative to using the wall box kit and its ability to protrude from the bottom of the screen allows

line-of-sight control even in a recessed ceiling installation.

Connection pins

inside

case

Connection pins

inside

case

Sensor

Watt-mounted

Receive

(Extension

Sensor)

Wall Box

Sensor

Bubble

Level:

Included with the installation package is a small bubble level that can be useful in

determining if the screen is perfectly level when installing.

NOTE

①

Please use the Down side as the bottom.

Bubble level

②The Bubble should be in the middle position to determine that it is level.

①

Connection

pins

inside

case

To Projector

Red

DC12V

DC5V

Black

Video Projection Interface

www.elitescreens.com / [email protected]

SCREENS

Please read this

uide prior to installation.

●Make sure the current rating is equal to that of the appliance rating when an extension cord is

Used.

●Do not use any accessories not provided by the manufacturer with this screen. We will not be

responsible for any risks of fire, electric shock, or injuries resulting from the misuse of this product

with accessories not designed for it.

●Make sure the screen is mounted at a perfect horizontal level. We suggest consulting with

a professional if you are uncertain on how to perform a proper installation.

INSTALL

TION

*Allow

” of spacing between the front and back of the screen

I. MasonryAnchors are used on concrete/masonry wall/ceilings; Plasticdrywall anchors are included

for drywall mounting

II. Wood screws are to be used for wooden wall/ceiling studs on screen sizes less than or equal to 120

inches (diagonal). Masonry anchors should be used for wall/ceiling installations of screen sizes greater than

120 inches

(

dia

onal

)

III. Install the Aluminum Extruded Hanger Set onto the slide channel and move to the desired position

before locking it by tightening the connecting bolt.

MOU

NTING

ACCESSO

RIES

Scre

Nut (M10)*4

Bolt*2

Alum Extruded

Hanger*2

Masonry

Anchor*2

Upon assembly, the bracket will slide into

the casing rails for mounting.

Scre

Nut (M6)*4

Washer*4

Plastic Plug*2

Wooden

Screw*2

Warning: These are standard accessories included with the ceiling/wall

brackets. Models may vary but anchors will not.

②

www.elitescreens.com / eliteinfo@elitescreens.com ③

SCREENS

6.02 mm. in width

The 4 prong cable will be

connected from the wall box

to the screen.

Although the IR remote requires direct line of

sight with the wall box in order to function, the

wall box can be hidden from sight, and operated

using the RF remote. When depressing the

directional buttons you should hear a faint click

signifying that the signal successfully transmitted

to the screen.

The 3 prong cable will be

connected from the outlet

to the control box.

IR Receiver

1”7 8

Stop

Down

IR codes

Up = 0XDD

Stop= 0XCC

Down= 0XEE

The IR (Infra-Red) remote has a range

of 15 Ft. with an AAA battery size

The RF (Radio Frequency) remote

has a range of 30 Ft. with an AAA

battery size

** Please remember to always point to the wall switch receiver when using the IR remote. The IR remote can also work with

Universal Learning Remote Control usually by programming the Screen's IR codes in your Universal Learning Remote.

③

AAA

www.elitescreens.com / eliteinfo@elitescreens.com

SCREENS

REFEREN

ONLY:

(Attention: This adjustment is not required. The screen's tension has been set

to achieve its best performance. Always contact an Elite Screen Technician for

assistance to avoid damaging the screen and voiding your warranty.)

Pulling the knob and turning it Clockwise it will create more tension

to the screen. By pulling the knob Counterclockwise it will start to

release tension

e e

c screen

oes no

move, p

ease c

ng:

1. Check the power supply first. The screen will understandably not move without power.

2. Make sure the power cord is firmly plugged to the power outlet.

3. Make sure that all cable connections are secure.

4. If the screen works well with the line switch but not with the remote control, please make sure the

remote controls have fresh batteries or replace them with new ones. Change the battery every 6

Months to ensure proper operation of the remotes.

5. For all other problems, please contact Elite Screens at Techsupport

elitescreens.com

Or call 1-877-511-1211 Ext. 202 / 234.

④

www.elitescreens.com / eliteinfo@elitescreens.com

SCREENS

1. Q: What are the differences between the IR and RF remotes?

n IR

(

Infra-Red

)

remote is desi

ned for short distance use, like

our t

ical television

remote. IR requires direct aim at the IR receiver located inside your 3-way wall box. RF remote control is

designed for long distance use. The RF code is unique only work to your 3-way wall switch that also came

with your screen. If the RF remote control is lost or destroyed, the entire 3-way wall switch will need to be

replaced in order to continue having RF control.

2. Q: How is the screen material cleaned?

A: The screen material can be cleaned with mild soap and water only. Do not use cleaning substances,

chemicals, or abrasives as it will damage the screen material.

3. Q: What t

e of batteries do the remote controls use?

A: The IR and RF remote controls use AAA alkaline batte

ies.

4. Q: Can

ou manuall

ull down this electric screen?

bsolutely not, manually pulling down the screen will damage the electronic motor rolling system.

5. Q: Can the electric screen be used in 220-volt outlets?

A: No, the screen can onl

be used in 110-volt outlets.

6. Q: What is the recommended distance m

first row of viewers should be at?

A: The recommended minimum distance should e

ual the dia

onal width of

our screen

viewing surface. However, this may vary depending on the projector type and lighting environment.

7. Q: How hi

h should I han

the

ect or screen?

A: The recommend lowest level of the pro

ector screen should at an e

e level of the first row

seat.

8. Q: Whom do I call for Technical Su

ort or a Trouble Re

ort?

A: The best wa

to re

ort a

roblem is to send an email to Techsu

ort

elitescreens.com

⑤

www.elitescreens.com / eliteinfo@elitescreens.com

SCREENS

One

(

)

ear warrant

arts and labor from

urchase date as follows

(

exce

for refurbished units as specified below

)

Refurbished units carr

a 90-da

arts and labor warrant

Demo units or open box items carr

a full 1-

ear

arts and labor warrant

Each

art

will be res

onsible for one wa

shi

durin

the warrant

eriod.

A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement or to

authorize a return for warranty repair. Elite Screens will, at their sole option, replace or repair the defective unit

with a brand new replacement *(see exceptions below) after the defective unit is received. Once the product is

received, Elite Screens will send out a new *unit to the customer by ground service (subject to inventory

availability). Please do not return any unauthorized items to Elite Screens, as they will be refused.

The RMA number must be included on the outside label of your shipping box and shipping documents. Our

warehouse is not authorized to accept returns without an RMA number on the shipping label. RMA numbers are

valid for 45 days from the date of issue.

Missing Parts must be reported within 7-days of receipt. If reported after 7 days, customer will be

responsible for shipping and handling fees. If reported after 30 days of receipt, customer is responsible for

cost of the parts and shipping & handling fees.

●All shipping damages must be reported with in 7 business days upon receipt of the product. After 7 days,

the Customer is responsible for all incurred costs.

●Inspect all shipments upon arrival. If damage or loss is apparent upon delivery do not accept the shipment

until you make a notation of the damage on all copies of the carrier's delivery receipt and have the driver

sign all copies to acknowledge the notation. Do not sign a receipt for damaged or missing cartons or there

will be no basis for a claim. Ask the carrier to make a detailed inspection of the damage. File a claim with

the carrier. Cooperate and follow up as necessary to secure final settlement

●Immediately advise Elite Screens of all damages or problems. Do not return merchandise to Elite Screens,

File your claim with the carrier and enclose copies of the bill of lading (signed by the driver) and inspection

report as support. Keep all packing materials and boxes with the damaged product Do not throw anything

away. Although Elite Screens will provide any assistance possible we cannot be responsible for the actual

filing of claims on the carrier or accept liability for non-collectable freight claims.

For Warranty and Service requests please fill out a RMA / Service Form at:

http://www.elitescreens.com/service.htm

Please visit this link for full Warranty information:

http://www.elitescreens.com/service_form.htm

⑥

www.elitescreens.com / [email protected]

SCREENS

TWO WAYS TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC.

A. On Line (Faste

and Easier)

www.elitescreens.com/register.html

A. Fill out & Fax to (562) 926-8655,Attn: Customer Service Dept

*You

Name:

Address:

Cit

/State/Zi

*EmailAddress:

*Phone:

*Screen Model:

*Serial Number:

*Date of Purchase:

*Dealer / Reseller Purchased from (name of the reseller):

What is your Projector Model:

Application: ___ Home ___ Education Corporation Government

___ Others

How would you rate this screen? ___ Excellent___ Good ___ Ok ___ Improvement

Needed

Comments:

If you have pictures of your screen you'd like to share with us, please email your pictures to

eliteinfo

elitescreens.com

For any warranty claim inquires, please email to

[email protected] o r 877-511-1211 – Customer Service Div.

For any technical inquiries, please email to

[email protected] or 877-511-1211 – Customer Service Div

Andere Handbücher für CineTension2 Series

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens Ez-Frame Series Bedienungsanleitung

Elite Screens

Elite Screens Evanesce Tension Series Bedienungsanleitung

Elite Screens

Elite Screens F100XWH1 Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

Elite Screens

Elite Screens Starling Tab-Tension CLR 3 Series Bedienungsanleitung

Elite Screens

Elite Screens WhiteBoardScreen Series Bedienungsanleitung

Elite Screens

Elite Screens EDGE FREE Aeon AcousticPro UHD Series Bedienungsanleitung

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Bedienungsanleitung

Elite Screens

Elite Screens Raptor Series Bedienungsanleitung

Elite Screens

Elite Screens Yard Master 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Manual SRM Pro Series Bedienungsanleitung

Elite Screens

Elite Screens SILVERMAX106H2 Bedienungsanleitung

Elite Screens

Elite Screens Sable Frame 2 Series Bedienungsanleitung

Elite Screens

Elite Screens SilverFrame 100GH1 Bedienungsanleitung

Elite Screens

Elite Screens QuickStand Drape Series Kurzanleitung

Elite Screens

Elite Screens VMAX2 (Plus) Series Bedienungsanleitung

Elite Screens

Elite Screens Aeon CineGrey 3D AR150H-AT Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

Elite Screens

Elite Screens AEON series Bedienungsanleitung

Elite Screens

Elite Screens Tripod B Series Bedienungsanleitung

Elite Screens

Elite Screens Spectrum 2 Series Kurzanleitung

Elite Screens

Elite Screens B SERIES Gebrauchsanweisung

Elite Screens

Elite Screens OMS103HR Bedienungsanleitung

Elite Screens

Elite Screens Lights-On Portable Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung