Elite Screens IWB85SW2a Bedienungsanleitung

041217 DR 1 www.eliteproav.com

Insta-DE2a/2aF Series

Self-Adhesive Dry-EraseFront Projection Screen Film

with Frame Border and Pen Tray

User’s Guide

Thank you for choosing the Insta-DE2a Series dry-erase whiteboard projection screen! Please read through this

user guide before utilizing the screen. Correct usage and maintenance will ensure a long product life.

Precautionary Notes:

Before using the dry-erase function of your whiteboard screen, please make note of the following instructions to

properly maintain and clean your dry-erase surface projection screen. (These Whiteboard cleaning tips are just

as relevant with any dry-erase writing surface as they are with our Whiteboard-Projection Screens.)

1.Only use a high density foam eraser when removing dry-erase markings from the Whiteboard screen.

2. Do not use abrasive erasers as these may scratch the surface of the screen.

3. Never spray the whiteboard cleaner solution onto the surface while marker writing is present and then attempt

to use a high density foam eraser to remove. This will only smear the dry-erase marker ink making the surface

more difficult to clean and will likely ruin the foam eraser.

4. If there are any dry-erase markings left behind even after attempting to remove themusing our high density

erasers, spray our whiteboard cleaning solution directly onto the screen surface and use only a soft microfiber

cloth to wipe-down and clean the area.

For a video demonstration, please visit: http://www.elitescreens.com/whiteboardscreen-cleaning

If replacement cleaning accessories are needed, please visit the Whiteboard cleaning accessories section of our

website at http://www.elitescreens.com/clean-whiteboard

Product Features

Anti-reflection surface reduces glare and hot-spot while using a

projector.

Special anti-scratch layer to ensure long use as a dry-erase/projection

screen.

1.1 gain with 180 degree wide viewing angle.

Award winning and GREENGUARD certified VersaWhite material.

Application Advantages

Instantly converts flat surfaces/walls into a dry-erase whiteboard projection screen.

Includes adhesive black velveteen border to enhance contrast and overall appearance.

Perfect dry-erase and projection solution for today's short throw projectors

Ideal and effective instructional presentation tool in the classroom, boardroom, and training facilities.

041217 DR 2 www.eliteproav.com

For a full installation demonstration, please see our Insta-DE 2aF Installation Video

Installation Video

Watch our installation video on-line at

www.elitescreens.com/ide2afinstall

or scan the QR code

Product Specifications

What’s in the package

Please make sure all parts listed below are included.

Notes: For best results and maximum product longevity, ONLY use a high density whiteboard eraser.

Frame and Pen Tray Parts List

Specifications:

Color display

White

Thickness

2.1mm

Material composition

High molecular weight copolymer of Terephthalic acid ethyl esters

Weight

377g/m2

Temperature

At room temperature

Gain

1.1

Viewing Angle

180°

Parts List

QTY

a. Insta-DE2a Screen Material Film Roll

b. Pen Holder (Self-stick cradle)

c. 4.5mmx30mm screw

d. Whiteboard markers (pens)

e. High density eraser

f. Glue powder bag

See table

g. Scraper (smoothing tool)

Model Number

Powder bag qty

iWB114XW2aF

iWB5x10W2aF

iWB5x20W2aF

Frame Parts Qty

Part A

Qty

Part B

Qty

iWB114XW2aF

iWB5x10W2aF 2 6

iWB5x20W2aF 2 10

041217 DR 3 www.eliteproav.com

Tools required (not included)

Carpenter’s Pencil

Tape Measurer

Sponge

150 grit sandpaper

Roller cover and

frame

Level

Paint Tray

Dust Mask

Safety goggles

Painting tape

Acrylic based

Primer

Strainer

Whisk

Measuring cup

Small bucket

Scraper

Step Stool/Ladder

Preparing the installation surface:

The Insta-DE 2aproduct is to be solely installed on a flat Level 5 surface. The dry erase function of this

product requires a smooth writeable surface. The smoother the surface, the better the result of the finished

product will be.

Any surfaces that are textured (ex. orange peel, drilled holes, glue/tape residue, dents, etc.) should be patched,

sanded, and primed before applying the Insta-DE2ascreen. We recommend sanding the area first to make sure

you have a clean flat and smooth surface. Failure to remove such imperfections can damage the product.

EliteProAV is not responsible should these instructions are not properly followed.

The warranty of this product will be voided if any bubbling occurs due to the use of an after-market

spray adhesive or if the screen was applied on to a textured wall.

Before applying the Insta-DE 2a, the application surface must be dry, clean, smooth, and structurally

sound.

1. Clean the surface to remove any dirt, grease, and wax.

2. Fill any depressions or holes with a drywall compound

3. Use sandpaper to smooth any bumps and blemishes. Sand until the surface is completely flat.

4. Level-5 finish to the surface and apply one coat of acrylic based primer.

Commercial use recommendation

If you would like your screen to have a professional-grade finish that is flat, durable, and free from

imperfections – EliteProAV strongly recommends hiring a professional wallpaper installer.

041217 DR 4 www.eliteproav.com

Glue Powder Compound Method for dry-wall (porous surfaces) installations

Installation

We strongly recommend three or more people for this installation.

1. Measure and draw a line around the screen installation area.

2. Apply one coat of Professional R-35 Primer and allow it to dry.

3. Un pack the Insta-DE 2a material from the box and lay it on a clean surface.

4.Scrape the installation area to assure a smooth surface. Sand as needed and clean dust with sponge.

5. Pour 25 oz. of room temperature water into a bucket, mix it with an entire glue powder bag and stir it with a

whisk until all lumps are gone and the compound has a syrup texture. This will make the mixture into an

adhesive compound for sticking the film to the wall.

Note: Once the compound has been mixed, it must be applied within 4 hours to ensure a sealed installation

of the Insta-DE 2a to the wall. Use one bag for every 25 oz. of water.

6. Pour the mixed glue compound thru a strainer into a paint tray. This is to avoid using compound that has

lumps which could result on the wall and causing bumps on the material.

7. Put a 3-4-inch piece of painter’s tape on the outer edge markings of the screen’s installation area. Space them

out approximately 18 inches apart.

8. Dip the paint roller in the paint tray and evenly apply a thin coat of the glue compound to the wall surface in 5

feet increments.

Do not allow the glue to dry. Use a spray bottle to gently wet the dry areas.

9. Carefully place and align the Insta-DE 2aon the left-hand side of the installation area. Once it has been

placed, peel off18 inches of the back film to expose the self-adhesive backing and attach to the installation area.

10. Use the painter’s tape that was put on the outer edge and tape the Insta-DE 2a to keep it from moving.

Note: The Insta-DE 2a material cannot be moved once attached, please make sure it is properly aligned on

the marked position.

11. Smoothing the Insta-DE 2a

a) Start from the Right-Middle area of the Insta-DE2a.

b) Make sure the Insta-DE2a adheres properly to the wall before proceeding.

c) Continue scraping as needed in an up/down/left direction as shown in the picture below, Step-2, Step-3.

Continue doing this until all material is attached.

Wall

041217 DR 5 www.eliteproav.com

11. Final Inspection:

Flash a light source directly on the surface of the Insta-DE2ato help inspect for air bubbles or dust.

Note: The Insta-DE2ashould not come off at this stage. If air bubbles are present, the only way to remove

them is to smooth them out.

13. Adhesion curing time:

In order to allow the Insta-DE2a and wall to properly bond, please refrain from touching and using the

dry-erase feature of the Insta-DE2afor a period of 2 days after the installation has been completed.

Self-adhesive Method for non-porous surfaces

1. Wall preparation:

Clean the entire non-porous surface with a wet sponge or a lint-free towel

2. Measure and draw a line around the screen installation area.

3. Moisturize the screen installation area:

a) Spray water on the screen installation area evenly with a sprayer.

b) Make sure the entire area where the Insta-DE2a will be installed is wet lightly (do not drench).

Note: The adhesive may not stick appropriately if the installation area is not sufficiently wet.

Wall

041217 DR 6 www.eliteproav.com

4. Procedures for attaching the material:

a) Carefully place and align the Insta-DE2aon the right-hand side of the installation area. Once it has

been placed,peeloff18 inches of the back film to expose the adhesive.

b) Spray the adhesive area to allow the Insta-DE2a the ability to move within the wet installation area.

c) Press the Insta-DE2a down with both hands to firmly position it in place.

d) As one person holds the Insta-DE2a in place, the other person peels off the backing from right to left.

e) Spray the exposed adhesive back of the Insta-DE2a and continue until the entire area is wet.

f) The Insta-DE2a material at this point can be easily moved and adjusted within the installation area if

needed.

5. Smoothing, scrapping out air bubbles and water:

Caution: The scraper’s edge is sharp. Carefully scrape the screen in a 45 degrees angle when removing air

bubbles to avoid scratching the surface.

a) Start from the Right-Middle area of the Insta-DE2a. Scrape up/down/left to remove the air

bubbles/water and dry any water excess with a lint-free cloth.

Note 1: Dust or other matter may reside within the Insta-DE2a and the wall. To remove such debris,

simply peel back the Insta-DE2a from the wall and clean it with the mixture described in step 3-a.

b) Make sure the Insta-DE2a adheres properly to the wall after cleaning before proceeding.

c) Continue scraping as needed in an up/down/left direction as shown in the picture below, Step-2, Step-3.

Note 2: Occasionally, water may come back in the areas that were just scrapped out. To avoid this from

happening, please make sure to dry any excess water immediately with a clean sponge or lint-free

cloth as soon as water is squeezed out.

6. Final Inspection:

Flash a light source directly on the surface of the Insta-DE2ato help inspect for air bubbles or dust.

Note: The Insta-DE2ashould not come off at this stage. If air bubbles are present, the only way to remove

them is to use a scraper to squeeze them out.

7. Adhesion curing time:

a) In order to allow the Insta-DE2a and wall to properly bond, please refrain from touching and using the

dry-erase feature for a period of 2 days after the installation has been completed.

b) It is normal for the surface of Insta-DE2a to have slight wavy edges. These will go away and flatten

after1-2 days.

041217 DR 7 www.eliteproav.com

Frame Border Installation

The circular labels on the vertical frame pieces indicate their proper position for completing the installation.

Proceed with Step 1 to begin.

Attention:

Please be sure that the walls are clean and free of debris before installing the frame.

041217 DR 8 www.eliteproav.com

The following velvet border installation steps are intended for the Insta-DE 2a Series only.

Adhesive black velvet border installation

1. Measure the top/bottom and left/right sides of the Insta-DE2 screen to obtain the required length of the velvet

border you will need to use for bordering your screen.

2. Peel a small portion off of the velvet border and place it about half an inch over the white area of the screen.

Continue to peel off and roll out the remainder of the velvet border until you have reached the end and cut

the edge.

Note: For best results we recommend cutting the edge in a 45° angle.

3. Repeat the process for the remainder of the sides until all sides are bordered as shown below.

Tray Installation

Remove both labels

Plastic dry-wall anchor

M4x6mm round head screw

5x50mm wood screw

Support bracket

041217 DR 9 www.eliteproav.com

Attach the wall brackets to the wall and tray as shown above to complete your installation.

DIAGRAM OF FINISHED INSTALLATION

Use only the included erasers to remove and erase dry-erase markings. For a deep clean, we

recommend using a non-alcohol based dry-erase board cleaner with a soft microfiber cloth.

Elite offers a replacement kit (part number ZER3) which includes:

1 x bottle of 8.45 oz cleaning solution

1 x microfiber cloth

2 x high density foam erasers

2 x sets of dry-erase markers (4 total)

Contact your reseller or visit shop.elitescreens.com for pricing and purchase.

Safety Precautions:

1. Avoid using sharp objects directly on the screen which can result in permanently damaging the product and

voiding your warranty.

2. Creases or wrinkles caused by improper installation are not removable.

041217 DR 10 www.eliteproav.com

Please be advised:

The above picture is the result of an improper installation. The main factor that contribute to this should be

avoided per the tips below.

•The surface to which you are installing this material to should be perfectly smooth. If in case the

surface is uneven, it is recommended to place a smooth board over the desired space of the install

first. This will eliminate any bubbling of the material over time.

Dimension Table

Insta-DE 2a Dimension Table

Model

Number

Diag.

Size

Aspect

Ratio

View Area

(HxW)

View Height

(A)

View Width

(B)

Thickness

(C)

Unit: Inches

IWB85SW2a

85"

1:1

60.3"x60.3"

60.3

0.0063

Unit: mm

IWB85SW2a

85"

1:1

60.3"x60.3"

1531

0.2

Note: Data Error ±1"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens Manual Tab-Tension 2 Series Bedienungsanleitung

Elite Screens

Elite Screens F100NWH Bedienungsanleitung

Elite Screens

Elite Screens Lunette Series Bedienungsanleitung

Elite Screens

Elite Screens Insta-DE 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Kestrel Home Series Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

Elite Screens

Elite Screens ezFrame Plus Series Bedienungsanleitung

Elite Screens

Elite Screens SilverFrame 100GH1 Bedienungsanleitung

Elite Screens

Elite Screens Ez-Frame Series Bedienungsanleitung

Elite Screens

Elite Screens CineTension 2 Series Bedienungsanleitung

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Bedienungsanleitung

Elite Screens

Elite Screens Evanesce Tab-Tension B Series Bedienungsanleitung

Elite Screens

Elite Screens DIY Wall 2 Series Bedienungsanleitung

Elite Screens

Elite Screens CineTension 2 Series Bedienungsanleitung

Elite Screens

Elite Screens EVANESCE TAB-TENSION Series Kurzanleitung

Elite Screens

Elite Screens Elite Home 2 Series Bedienungsanleitung

Elite Screens

Elite Screens StarFrame Series Bedienungsanleitung

Elite Screens

Elite Screens GolfSim Bay Series Bedienungsanleitung

Elite Screens

Elite Screens Elite Home 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Tab-Tension 3 Series Bedienungsanleitung

Elite Screens

Elite Screens F60XWV1 Bedienungsanleitung

Elite Screens

Elite Screens EDGE FREE Aeon Series Bedienungsanleitung

Elite Screens

Elite Screens Planate Tab-Tension Series Leitfaden

Elite Screens

Elite Screens QuickStand Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung