Elite Screens Spectrum2 Series Bedienungsanleitung
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 1
Electric Motorized Projection Screen
Spectrum2 Series
User’s Guide
Make sure to read this user’s guide and follow the procedure below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved
changes or modifications (except for cutting the power cord for hardwire installations) to this unit are
prohibited and will void your warranty. For more information, please contact our Technical Support
Department at (877) 511-1211 Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
Never overload the power cord to prevent an electric shock or fire due to a loose contact or a
short circuit.
There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by
yourself. No one except authorized technicians can open and make repairs to this unit.
Make sure the power source this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
Avoid direct Sunshine, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Important Safety & Warning Precautions
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 2
Cut off the power supply first before transportation or maintenance.
Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.
Due to various installation environments, the instructions provided in this user’s guide are for reference
only. Please consult a professional installation company for further installation and safety advice. The
installer must insure that proper mounting hardware is used to provide adequate strength suitable for
the installation. Elite Screens is not liable for any faulty installations.
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop
in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.
Installation Warning
Pre-Installation
NOTE
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 3
Hardware Parts List for the Spectrum2 Series 0
Please make sure all parts listed below are included before proceeding with the installation.
a. b. c. d. e. f.
Installation Instructions
Please consult a professional Installer. Elite Screens is not liable for faulty installations.
Flush Mount to the Wall
1. Mark the location of where the screen is to be installed, drill your holes, and insert the M10
Anchors (c).
2. Install the Mounting Brackets (a) to the wall and secure with the M4x50 Screws (b).
Mounting Bracket
Fix Plate 1
M4x50 Screw
Anchor
Wall Mounting Bracket
Fix Plate 2
Mounting Bracket
3. Attach the screen to the Mounting Bracket by inserting the top of the case to the first fix plate,
and securing the back of the case to the second Fix Plate. Make sure the case slots are securely
attached to the Mounting Bracket.
Hardware Parts List
QTY
a. Mounting Bracket
2
b. M4x50 Screw
4
c. M10 Anchor
4
d. Suspended Ceiling Bracket Connector
2
e. M5x15 Screw & Bolt
4
f. Bubble Leveler
1
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 4
Mounting Bracket Mounting Bracket
Fix Plate 1 Fix Plate 2
Mounting Bracket Case Slot 1
Case Slot 2
Flush Mount to the Ceiling
1. Mark the location of where the screen is to be installed, drill your holes, and insert the M10
Anchors (c).
2. Install the Mounting Brackets (a) to the ceiling and secure with the M4x50 Screws (b).
Ceiling M10 Anchor
Screen Case
M4x50 Screw
Mounting Bracket
Fix Plate 1
Mounting Bracket
Fix Plate 2
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 5
3. Attach the screen to the Mounting Bracket by inserting the top of the case to the first Fix Plate,
and securing the back of the case to the second Fix Plate. Make sure the case slots are securely
attached to the Hanging Bracket.
Suspended Ceiling using Chains (additional hardware required)
1. You can also hang the screen on a ceiling by using chains (not included).
2. Connect the Suspended Ceiling Bracket Connector (d) to the Mounting Bracket (a) and secure with
the M5x15 Screws & Bolts (e).
M5x15 Bolt
(e) Suspended Ceiling Bracket Connector
(d)
Mounting Bracket
(a)
M5x15 Screw
(e)
3. Insert chains (not included) through the loop holes of the Suspended Ceiling Bracket Connector (d).
Suspended Ceiling Bracket Connector
Loop Holes
Fix Plate
1
Fix Plate
2
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 6
Built-in 3 Way Control Switch
1. The Spectrum2 Series comes with a 3 Way Control Switch attached to the Power Cord, which is 3.5
meters in length.
2. Use the provided Bubble Level (f) to ensure the screen is level before plugging in the power cord
3 Way Control
Up/Stop/Down
Switch
Remove Screen from Mounting Brackets
1. Pull down on the Mounting Bracket Release Tab and remove the bottom of the case first, away
from the wall/ceiling, followed by the top of the case.
Release Tab Pull Bottom of case first away from wall/ceiling.
Rev.042613-JA
www.elitescreens.com info@elitescreens.com 7
ZPM-RT Optional Remote Control Kit for Spectrum2 Series 1
Please contact Elite Screens to purchase the optional ZPM-RT Remote Control Kit.
55”
A. B. Red+ Green -
IR Remote RF Remote
C. D. IR “eye”receive E. 5-12V Trigger cable
3 Way Wall Switch
G. Wall Box
110”
Inhaltsverzeichnis
Andere Elite Screens Projektionsfläche Handbücher
Elite Screens
Elite Screens Kestrel Tab-Tension Series Bedienungsanleitung
Elite Screens
Elite Screens PowerMax Series Bedienungsanleitung
Elite Screens
Elite Screens Spectrum Series Bedienungsanleitung
Elite Screens
Elite Screens Kestrel Series Bedienungsanleitung
Elite Screens
Elite Screens Tab-Tension Series Bedienungsanleitung
Elite Screens
Elite Screens TE100HC2 Bedienungsanleitung
Elite Screens
Elite Screens isf CineWhite UHD-B Sable Frame B2 Series Bedienungsanleitung
Elite Screens
Elite Screens Kestrel Stage Series Bedienungsanleitung
Elite Screens
Elite Screens AR100H2 Bedienungsanleitung
Elite Screens
Elite Screens CineTension 2 Series Bedienungsanleitung
Elite Screens
Elite Screens Aeon CineGrey 3D AT Series Bedienungsanleitung
Elite Screens
Elite Screens QuickStand Drape Series Kurzanleitung
Elite Screens
Elite Screens B SERIES Gebrauchsanweisung
Elite Screens
Elite Screens Aeon CLR 3 Series Bedienungsanleitung
Elite Screens
Elite Screens EVANESCE TAB-TENSION Series Leitfaden
Elite Screens
Elite Screens M135XWV2 Bedienungsanleitung
Elite Screens
Elite Screens Evanesce Tab-Tension ITE120HW2 Bedienungsanleitung
Elite Screens
Elite Screens Kestrel FE100H Bedienungsanleitung
Elite Screens
Elite Screens Ez-Frame Series Bedienungsanleitung
Elite Screens
Elite Screens CineTension 2 Series Bedienungsanleitung
