Elite Screens VMAX2 (Plus) Series Leitfaden

Updated 3/22/2017 1 www.elitescreens.com

Tubular Motor Replacement Instructions

for VMAX2 models 135” and above / Spectrum models 135” and above

For technical support or further assistance, call 877-511-1211 x604

ATTENTION:

Elite Screens does not recommend making unnecessary adjustments to the screen, as improper

adjustments will damage the unit and void your warranty.

1. Remove the screws on the motor bracket and left end cap (facing the screen) with a Phillips

screwdriver, then remove the end cap.

2. After removing the end cap, carefully remove the decorative sheet by pulling it outward towards

the open end.

Decorative sheet

Decorative sheet removed

End cap

screws

Motor bracket

screws

Updated 3/22/2017 2 www.elitescreens.com

3. Remove the power cord and 3P cable, shown in the image below.

4. Using the screwdriver, at the right side end cap, push the roller out to expose the roller on the

open left side end of the housing. Being sure not to snag or scratch the material on the housing, lift

and pull the roller out from the left side enough to access the ground terminal.

5. Cut off the ground terminal and remove the motor.

Screwdriver pushing out

roller from right side

Ground

Terminal

Power cord

Ground Terminal

removed

Motor

Housing

Roller

Updated 3/22/2017 3 www.elitescreens.com

6. Separate the motor from the motor bracket and attach the same bracket to the new motor.

7. Install the new motor. Be sure to align the drive wheel with the ladder on the roller.

8. Place the bracket into the housing where the RJ45 port on the circuit board lines up with the hole

on the housing.

9. Two people are suggested for this step. While one person keeps hold of the left side, the other

will need to loop thin rope or twine around the motor cap on the right side of the roller. (This will help

guide the roller back into the housing and reconnect with the shock absorber core.) Push in the left

side end cap back into the housing while carefully guiding the right end of the roller into place.

Roller

Motor

RJ45 port

Remove the

motor bracket

from here

Updated 3/22/2017 4 www.elitescreens.com

10. After inserting the motor into the housing, insert the power cord and the 3P cable into the circuit

board. Then connect the power cable to the ground of the motor cable and clamp it with the ground

terminal.

11. Affix the ground terminal to the bracket and housing with screws removed in step 1.

Shock absorber core

Motor cap

Rope or

twine

Power cord

Power cable/Motor cable

Power cable/Motor cable clamped with ground terminal

Ground terminal

Updated 3/22/2017 5 www.elitescreens.com

12. Replace the decorative sheet removed in step 2.

13. Replace and secure the end cap with screws removed in step 1.

NOTE: After replacing the tubular motor, you may need to adjust the limit switch to drop the screen at

your preferred height.

For a local Elite Screens contact or Technical Support, please visit

www.elitescreens.com

Finished assembly.

Andere Handbücher für VMAX2 (Plus) Series

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens F100NWH Bedienungsanleitung

Elite Screens

Elite Screens GolfSim Portable Series Bedienungsanleitung

Elite Screens

Elite Screens SILVERMAX106H2 Bedienungsanleitung

Elite Screens

Elite Screens ezCinema Series Bedienungsanleitung

Elite Screens

Elite Screens Evanesce Tension Series Bedienungsanleitung

Elite Screens

Elite Screens Home100IWH2-A Handbuch

Elite Screens

Elite Screens Lunette Series Bedienungsanleitung

Elite Screens

Elite Screens Spectrum Series Bedienungsanleitung

Elite Screens

Elite Screens AEON series Bedienungsanleitung

Elite Screens

Elite Screens Manual Series Bedienungsanleitung

Elite Screens

Elite Screens Spectrum Tension Series Bedienungsanleitung

Elite Screens

Elite Screens StarFrame Series Bedienungsanleitung

Elite Screens

Elite Screens CineTension2 Series Bedienungsanleitung

Elite Screens

Elite Screens 2 CLR Series Bedienungsanleitung

Elite Screens

Elite Screens F100NWH Betriebsanleitung

Elite Screens

Elite Screens WB30VW Bedienungsanleitung

Elite Screens

Elite Screens AEON series Bedienungsanleitung

Elite Screens

Elite Screens Insta-DE Screen Bedienungsanleitung

Elite Screens

Elite Screens DE103C82H Bedienungsanleitung

Elite Screens

Elite Screens Manual Tab-Tension 2 Series Bedienungsanleitung

Elite Screens

Elite Screens EDGE FREE Aeon CineWhite UHD 2 Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens Saker Series Bedienungsanleitung

Elite Screens

Elite Screens Saker Series Leitfaden

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung