Elk Products ELK-319DWM Bedienungsanleitung

ELK-319DWM Wireless Door/Window Mini Sensor

Description

The ELK-319DWM is a Supervised, Wireless Door Sensor

that detects the opening and closing of doors or windows. The

small and low prole sensor and magnet are mounted using

screws (included) or double-sided adhesive tape (included).

As the door is opened or closed, the sensor transmits an

open (trip) or close (restore) signal to the panel. Additionally

transmitted signals include: tamper, hourly supervisory, and

low battery (as needed). The sensor is powered by two (2)

replaceable 3VDC, lithium coin-cell batteries.

This sensor is compatible with Elk’s 319MHz Receivers/Panels

as well as many other panels that operate on the 319.5MHz

Frequency and adhere to the ITI/Interlogix protocol.

Specications

RF frequency: 319.5 MHz

Compatibility: ELK-319 Receivers/Panels & other panels

that operate on the 319.5MHz Freq. and

adhere to the ITI/Interlogix protocol

Battery type: Two (2) 3VDC lithium coin-cell

(Panasonic or Varta Model CR2032)

Operating

Temp Range: 32 to 120°F (0 to 49°C)

Storage

Temp Range: -30 to 140°F (-34 to 60°C)

Relative

Humidity: 95% non-condensing

Dimensions 2.25” L x .1.0 x 0.50” in. (L x W x D)

Programming (Enrollment)

The following is a general guideline for programming (enrolling)

a sensor into the receiver or panel. For more extensive

instructions please refer to the receiver or panel instructions.

1. Place the panel into the Program mode.

2. Proceed to the WIRELESS SETUP menu.

3. Select the appropriate zone/sensor location number.

4. When prompted by the panel to trip the sensor for learning:

• Remove the sensor cover

• If present pull the battery pull tab out to power the sensor

• The panel should acknowledge the sensor has been learned

by keypad display and/or audio alert (depending on the

panel). If enrollment fails to occur repeat the process

but remove and reinstall the battery OR try pressing and

releasing the tamper plunger.

5. Repeat the above process for any additional wireless

sensors. Proceed to the zone programming to assign each

sensor’s zone denition.

6. Exit programming mode when nished.

Mount Sensor on the jamb of the

door or window directly opposit

the magnet.

Mount Magnet on the moveable

portion of the door or windoe di-

rectly opposite the top right corner

of the Sensor.

Installation Guidelines and Mounting

• Sensor should be temporarily attached at the desired

location and successfully tested with the panel/receiver

prior to drilling any holes or permanently mounting.

• Mounting this sensor on metal can negatively a󰀨ect the

transmitting range and magnet gap performance.

• Install the sensor within 100 ft. of the receiver or panel.

• Mount the sensor on the non-moving frame surface and

the magnet on the actual moving door. If one sensor is to

be used for a double acting door then mount the sensor on

the least used gate/door.

• Mount sensors at least 5 inches above the oor to avoid

damaging them.

• The sensor can be attached to wood, vinyl, and some

metallic surfaces if pre-installation test are positive.

• Align the magnet directly across from the top right edge of

the sensor with a gap of no more than 5/16” (8 mm) for wood

surfaces and no more than a 1/4” (6 mm) gap for non-wood

surfaces.

• Based on the magnet location, spacing, direction of

operation and the material of the mounting surface, the gap

for opening will vary between 1/8” (3 mm) and 1 ¾” (44 mm).

Desired operation should be checked before permanent

installation.

• After mounting is completed, retest the sensor using the

procedure described.

TM Interlogix is a registered trademark belonging to United Technologies.

For Additional Tamper Security

1. Punch out the tamper cover on the bottom of the sensor,

and using the small screw secure it to the mounting location,

when the sensor is removed “tampered” the tab remains

providing a tamper condition.

All manuals and user guides at all-guides.com

FCC AND IC COMPLIANCE STATEMENT:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment o󰀨 and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di󰀨erent from

that to which the receiver is connected.

Elk Products, Inc.- 3266 Hwy 70 - Connelly Springs, NC 28612 http://www.elkproducts.com 11/19/2018

Limited Warranty

THIS WIRELESS SENSOR IS WARRANTED TO BE FREE FROM

DEFECTS AND WORKMANSHIP FOR A PERIOD OF 2 YEARS

FROM DATE OF MANUFACTURE EXCLUDING BATTERIES.

BATTERIES USED WITH WIRELESS DEVICES ARE NOT

WARRANTED.

MANUFACTURER HEREBY DISCLAIMS ANY AND ALL OTHER

WARRANTIESAND REPRESENTATIONS, WHETHER EXPRESS,

IMPLIED, STATUTORY OR OTHERWISE INCLUDING (BUT NOT

LIMITED TO) ANY WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT

TO THESE PRODUCTS AND ANY RELATED SOFTWARE.

MANUFACTURER FURTHER DISCLAIMS ANY OTHER IMPLIED

WARRANTY UNDER THE UNIFORM COMPUTER INFORMATION

TRANSACTIONS ACT OR SIMILAR LAW AS ENACTED BY

ANY STATE. (USA only) SOME STATES DO NOT ALLOW THE

EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE

EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE

OTHER LEGAL RIGHTS THAT VARY FROM STATE TO STATE.

MANUFACTURER MAKES NO REPRESENTATION, WARRANTY,

COVENANT OR PROMISE THAT ITS ALARM PRODUCTS

AND/OR RELATED SOFTWARE (I) WILL NOT BE HACKED,

COMPROMISED AND/OR CIRCUMVENTED; (II) WILL PREVENT,

OR PROVIDE ADEQUATE WARNING OR PROTECTION FROM,

BREAK-INS, BURGLARY, ROBBERY, FIRE; OR (III) WILL WORK

PROPERLY IN ALL ENVIRONMENTS & APPLICATIONS.

NOTE: Elk Products is not responsible for any changes

or modications not expressly approved by the party

responsible for compliance. Such modications could

void the user’s authority to operate the equipment.

Testing the Sensor

It is recommend that all wireless sensors be thoroughly walk

tested after installation and programming.

1. Place the panel into the Walk Test mode.

2. Monitor the keypad display as each sensor is tripped. Refer

to the receiver or panel for complete instructions. In some

cases there may be a signal strength indication.

3. Exit Walk Test mode when nished.

Battery Replacement

Low Battery trouble will be transmitted when the sensor battery

needs to be replaced.

NOTE: Replace both (2) batteries within 7 days following

a low battery trouble indication.

• Remove the cover from the sensor.

• Carefully slide out the old batteries.

• Insert the two (2) new batteries into the battery holder

slots.

• Observe Polarity shown on the lithium coin-cell battery.

CAUTION: Use only approved 3.0VDC Lithium

Battery: Panasonic or Varta model CR2032

• Replace the cover on the sensor test activate the

device at least ve times.

BATTERY WARNING:

Risk of re, explosion and burns. Do not attempt to

recharge or disassemble. Do not incinerate or expose

to heat above 212° F (100° C). Dispose of used batteries

properly. Keep away from children.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de

licence standard RSS (s). Son fonctionnement est soumis aux

deux conditions suivantes: (1) cet appareil ne doit pas provoquer

d’interférences et (2) cet appareil doit accepter toute interférence,

y compris celles pouvant causer un mauvais fonctionnement de

l’appareil.

In accordance with FCC requirements of human exposure to radio

frequency elds, the radiating element shall be installed such that

a minimum separation distance of 20 cm is maintained from the

general population.

FCC ID: 2ABBZ-RF-CMDWS-319

IC: 11817A-RFCMDWS319

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation. Changes or modifications not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-3B.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

All manuals and user guides at all-guides.com

Andere Elk Products Zubehör Handbücher

Elk Products

Elk Products ELK-319WS Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung