Elkay SOFT SIDES EZLMSN-EDFPVM217DK Gebrauchsanweisung

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 1

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left in the plastic bag

provided inside the installed unit for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices

to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a

metallic taste to it or has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.

Any drain  ttings provided by the installer should be made of plastic which will electronically isolate

the fountain from the remainder of the building’s plumbing circuits.

SOFT SIDES®Fountains with Vandal Resistant Bubblers

and Vandal Resistant Water Dispenser

INSTALLATION & USE MANUAL

LZLMSN-EDFPVM217DK

(Shown with optional ACCESS12X38-5 access

panel.)

EZLMSN-EDFPVM217DK

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 2

**NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI)

Figure 1 - Rough-in Dimensions

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 3

Figure 3 - LZLMSN-EDFPVM217DK Tube Routing

REQUIRED TOOLS AND MATERIALS

These tables show special tools and/or additional

materials (not provided) which are necessary to

complete installation of these units:

Figure 2 - EZLMSN-EDFPVM217DK Tube Routing

TO BUBBLER

FILTER

ASSEMBLY

WATER

INLET

Special Tools

Item Description Quantity

NONE

Additional Materials Not Included

Item Description Quantity

Unplated copper inlet pipe

Service Stop

90° 1-1/4” Drain Line

1-1/4” Tee Drain Line

TO BUBBLER

TO BOTTLE

FILLER

1. Make water supply connections (Fig. 10). Install a

shut-off valve and union connection to building water-

supply (valve and union not provided). Turn on water

supply and ush the line thoroughly.

Caution: DO NOT SOLDER tubes inserted into the

strainer or lter head as damage to the o-rings may

result.

2. Install mounting frame (instructions supplied with

mounting frame.

3. (For LZLMSN-EDFPVM217DK) Install the lter head

to the bracket, then install lter bracket on mounting

frame (Fig. 8), plumb from the lter outlet using the ¼”

elbow, poly tubing and ¼ x ¼ x ¼” tee, install lter.

3a. (For EZLMSN-EDFPVM217DK) Install ¼” tee,

copper tubing and strainer per (Fig. 2).

4. Install supplied 4” poly tubing and armaex to the

outlet of the previously installed tee or strainer. Connect

supplied ¼ x ¼ x ¼ tee to the 4” poly tubing.

5. Hang main panel on mounting frame hanger. Make

sure the poly tube do not get pinched between the panel

& mounting frame. Ensure the panel engages at the top.

Align fountain holes with mounting frame holes.

6. Remove protective coating from main panel.

7. Installing water Dispenser Place the unit into the

stainless panel and frame. Align the holes in the water

dispenser with the nuts in the panel. Attach the dispens-

er to the panel using four (4) supplied 1/4 x 20 screws.

TO BUBBLER

BOTTLE

FILLER

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 4

Connecting Catch Basin Waste Drain

Installing the drain is highly recommended to prevent

basin over ow.

The following steps cover the installation of the drain.

1. Remove the two screws attaching the drain basin to

the water dispenser. Remove the drain basin.

2. Place the drain basin on a  at, hard surface, such as

a piece of sacri cial wood. Carefully drill a hole in the

basin using a 1" hole saw using the centering-dimple

as a guide to center the hole saw.

Note: Do not use a 1-1/8" hole saw as this will make the

opening too large.

3. Trial  t the strainer. If the strainer does not  t, carefully

open the size of the hole. If it  ts well, place a small

amount of plumbers putty around the lip of the strainer

 ange and insert it into the hole.

4. Install the O-ring over the strainer threads.

5. Thread the strainer into the drain adapter.

Needle-nose pliers can be used to hold the drain

adapter from the top while tightening. Ensure that

the connection creates a watertight seal. The drain

adapter must be facing to the left.

Note: Twisting the strainer instead of the drain adapter

can compromise the seal created by the plumber's

putty.

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 5

6. Attach one end of the 3/4 inch  exible drain hose to

the 3/4 inch barbed drain adapter connection using the

supplied hose clamp. The supplied  exible drain is 13

inches long. If a longer drain hose is required, it must

be installer-supplied.

7. Place the drain basin back into the water dispenser

and reinstall the two screws.

8. Connect the drain adapter into the household waste

drain pipe.

If the p-trap is located inside a sealed walled, it must

have permanently-glued joints. If the p-trap is in an

accessible location, a standard non-glued p-trap is

acceptable.

Install the water dispenser’s front cover.

9. Line up the front panel with the dispenser frame and

attach using the  athead screws and a 3/32” hex

wrench.

10. Install the metal grate cover using the 4 Screws.

Note: Always consult local plumbing codes prior to

installation.

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 6

Figure 4 - Upper Panel Installation

Figure 5 - Fountain Installation

View From Rear

1. Install fountains with (8) 5/16-18 HHMS & (8) 5/16-18

nuts (provided) (Fig. 5). Connect the ¼” water lines from

each fountain to the remaining openings on the tee (cut

lines to  t as needed).

2. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip

trap. Trap on the bottle  ller side must be 1-1/2” O.D.

(provided by others).

3. Make  nal water supply connections.

4. These products are designed to operate on 20-105

PSI supply line pressure. If inlet pressure is above 105

PSI, a pressure regulator must be installed in the supply

line.

Caution: Any damage caused by connecting these prod-

ucts to a supply line with pressure lower than 20 PSI or

higher than 105 PSI IS NOT covered under warranty.

5. Verify proper dispensing from the bottle  ller by

placing a cup, under the water dispenser spout and

press the button and verify water dispenses. Note: the

 rst initial dispenses might have air in the line which may

cause a sputter. This will be eliminated once all air is

purged from the line. A steady stream of water assures all

air is removed. Check for leaks.

6. Check stream height from bubbler. Stream height is

factory set for 35 PSI supply. If supply pressure varies

greatly from this, remove push button (Item 5 - Fig. 8)

and adjust the screw on the regulator (Item 4 - Fig. 8). To

remove push button, loosen set screw (Item 7 - Fig. 8) on

bottom of the sleeve (Item 6 - Fig. 8) and pull out on the

button. Clockwise adjustment will raise stream height and

counterclockwise movement will lower stream height. For

best adjustment stream should hit basin approximately

6-1/2” from the bubbler. Reassemble the push button by

pushing in on button and tighten the set screw (Item 7 -

Fig. 8) in the sleeve (Item 6 - Fig. 8).

7. Install the bottom cover plates on fountains (Fig. 4).

8. Tighten back panel screws (Item 9 - Fig. 4).

9. Optional: Mount optional panels. Mount bracket on

wall per rough-in instructions. Slide tongue of panel under

edge of already installed panel. Tighten screws.

Once the installation is complete, the water has been

turned on, and any trapped air has been bled from the

system re-check for any water leaks.

24,25

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 7

NOTE:

When installing replacement bubbler and

pedestal, tighten locknut only to hold parts

snug in position.Do Not overtighten.

Figure 6 - Bubbler Details

VANDAL-RESISTANT BUBBLER DETAIL

Fig. 7

Filter Head

Assembly

used after 01/01/2021

3/8”

ter

Inlet

WATERSENTRY®PLUS FILTER PARTS LIST

(See Fig. 7)

ITEM

NO. PART NO. DESCRIPTION

51300C

51469C

Filter Assy-3000 Gal.

Assy-Filter & Brkt includes Fltr Head/

Mtg Brkt/John Guest Fittings/Screws

BASIN

1/4” tube

(if required – not included)

Locknut

Figure 8

Once the installation is complete, the water has been

turned on, and any trapped air has been bled from

the system re-check for any water leaks.

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 8

LCOVE

SSEMBLY

MAIN ENCLOSURE

ASSEMBLY

Figure 9

Figure 8

PARTS LIST

ITEM

NO. PART NO. DESCRIPTION

98481C

28782C

28783C

LK464

98530C

45960C

45663C

75672C

112627543890

111008343890

56092C

1000001994

55996C

2000001257

55000661

55000665

40045C

28823C

56280C

75560C

1000001772

111577343890

62223C

1000002062

Kit - Vandal-Resistant Bubbler Assy

Fountain Arm - Short

Fountain Arm - Long

Drain

Kit - Regulator/Nut/Holder

Push Button

Push Button Sleeve

Screw - Cap #6-32 x 5/16

Screw - #10-24 x .50 PHTC

Screw - #10-24 x .62 HHSM

Poly Tubing 1/4” (Cut To Length)

Kit - Tee 1/4 x 1/4 x 1/4 (3 Pack)

Strainer

Back Panel Assembly

Bottom Cover Plate - Short

Bottom Cover Plate - Long

Hex Nut

Regulator Mounting Bracket

Edge Trim - Chrome

Screw - 5/16-18 x 1.00 HHMS

Kit - Elbow 1/4 x 1/4 (3 Pack)

Nut - Hex 5/16-18

Copper Tube - 3/8” Cut to Length

Kit - Tee 1/4 x 1/4 x 3/8 (3 Pack)

2000001276 (Rev. A - 01/24)

EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK

Page 9

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

ELKAY MANUFACTURING COMPANY • 1333 BUTTERFIELD ROAD SUITE 200 DOWNERS GROVE, IL 60515 • 630.574.8484 • www.elkay.com

Figure 10 – Water Supply Connections

NOTE: WATER FLOW

DIRECTION

BUILDING WATER

INLET

SERVICE STOP

(NOT FURNISHED)

1/4” O.D. TUBE

WATER INLET

TO COOLER

3/8” O.D. UNPLATED COP-

PER TUBE CONNECT

COLD WATER SUPPLY Installation Package

The components for installation are packed in

three separate boxes, regardless of the type

of unit being installed. The boxes contain the

following:

Box No. 1: Wall Frame(s)

Box No. 2: Fountain(s), Arm(s) and Panels

Box No. 3: Water Dispenser

Additional materials, as noted in the Parts List,

are also shipped in these boxes.

TROUBLESHOOTING & MAINTENANCE

Orice Assembly: Mineral deposits on orice can

cause water ow to spurt or not

regulate. Mineral deposits may

be removed from the orice by

poking with a small round le

not over 1/8” diameter, or using

a small diameter wire.

DO NOT le or cut orice material.

Stream Regulator: If orice is clean, regulate ow as

in Step 14 of the installation instructions. If replacement

is necessary, see parts list for correct regulator part

number.

Actuation of Quick Connect Water Fittings: Cooler

is provided with lead-free connectors which utilize an

o-ring water seal. To remove tubing from the tting,

relieve water pressure, push in on the gray collar while

pulling on the tubing. (See Fig. 11) To insert tubing,

push tube straight into tting until it reaches a positive

stop (approximately 3/4”).

REPLACEMENT PART LIST

ITEM

NO. PART NO. DESCRIPTION

98546C

1000004698

2000001260

1000005392

56331C

70793C

1000001812

Kit - Aerator Replacement

Fitting - Hose to Trap

Kit - Alcove

Kit - Drain

Connector

Elbow 1/4 O.D. X 90

Kit - Bottle Filler Drain

NS = NOT SHOWN

Figure 11 – Quick Connect Fittings

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay FLEXI-GUARD SOFT SIDES ezH2O EDFP217WS F... Gebrauchsanweisung

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay EZWS-EDFPBM117K Gebrauchsanweisung

Elkay

Elkay LK4410FR FTN A Series Bedienungsanleitung

Elkay

Elkay EDFPW210C Installationshandbuch

Elkay

Elkay 4400FR-FTN Series Bedienungsanleitung

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay 4595FR Bedienungsanleitung

Elkay

Elkay EDFPB114C Gebrauchsanweisung

Elkay

Elkay Soft Sides ERO8C C Series Installationshandbuch

Elkay

Elkay Soft Sides Series Installationshandbuch

Elkay

Elkay EFA8 2YJO Series Installationshandbuch

Elkay

Elkay SWIRLFLO ENOBM28RAK Installationshandbuch

Elkay

Elkay SWIRLFLO FLEXI-GUARD ENOBM8C Installationshandbuch

Elkay

Elkay LK4430BF1 Bedienungsanleitung

Elkay

Elkay SOFT SIDES EDFP217WS F Series Gebrauchsanweisung

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay LVRCTL8 1D Series Installationshandbuch

Elkay

Elkay Swirlflo EDFPB114FPC Installationshandbuch

Elkay

Elkay 4400BFFR Bedienungsanleitung

Elkay

Elkay HTHBHVR8-NF-25N Installationshandbuch

Elkay

Elkay Space-ette FD700-10 1J-MDN Series Installationshandbuch

Elkay

Elkay FLEXI-GUARD ESRC8,13 1D Series Installationshandbuch

Elkay

Elkay SWIRLFLO Series Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung