Elkay SWIRLFLO FLEXI-GUARD ENOBM8C Installationshandbuch

ENOB8C

98004C (REV. A - 9/04)

SWIRLFLO Refrigerated fountains with FLEXI-GUARD

INSTALLATION, CARE & USE MANUAL

TM TM

Review these instructions before beginning installation. Be sure that installation

conforms to all plumbing, electrical and other applicable codes.

When installation is complete, ensure these instructions are left with building owner

for future reference.

Service to be performed by authorized service personnel only.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to

available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in

an electrolysis effect occurring in the fountain. This may result in water which has a metallic taste to it or

has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the installation,

and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation. Any

drain fittings provided by the installer should be made of plastic which will electronically isolate the fountain

from the remainder of the buildings plumbing circuits.

98004C (REV. A - 9/04)

ENOB8C



PP



PP



PP



PP



PP



PP



PP



PP



PP



PP



PP



PP



PP

0,1,080'(37+

%$&.:$///,1(

),1,6+(')/225



PP



PP

$'$

5(48,5(0(17

LEGEND

A = 1/4 O.D. Tube - Water Outlet Connection

B = 3/8 O.D. Tube - Water Inlet Connection

C = 1-1/4 Waste Tube

D = ELECTRICAL INLET

Figure 1 - Rough-in Dimensions

Model ENOBM8C

ENOB8C

98004C (REV. A - 9/04)

Special Tools

Item Description Quantity

NONE

Additional Materials

Item Description Quantity

1 Unplated copper inlet pipe

2 Service Stop

REQUIRED TOOLS AND MATERIALS

These tables show special tools and/or additional materials

(not provided) which are necessary to complete installation of

these units:

Figure 2 - Chiller Installation

CHILLER

INLET

CHILLER

OUTLET

Figure 3 - ENO Tube Routing

1. Install chiller: Remove front panel of chiller. Slide chiller

onto the shelf and position it to the left as per dimensions

in Figure 1.

Note: Building construction must allow for

adequate air flow on both sides, top and

back of chiller. A minimum of 4 (102mm) on

both sides and top is required. See chiller

installation for additional instructions.

2. Attach solenoid valve assembly to the underside of

cross member of mounting frame on electronic

sensor unit. (See Fig. 7).

3. Make water supply connections. Inlet port is marked on

the chiller (1/4 O.D. copper tube). Bend the copper tube

(provided) at an appropriate length from the chiller to

opening in frame. Install the in-line strainer (provided with

chiller) by pushing it in until it reaches a positive stop,

approximately 3/4 (19mm) on the marked chiller inlet port

(See Figs. 3) (Refer to Fig. 12 on page 7 for details on

assembling quick connect fittings). Attach an unplated and

deburred copper water inlet line and a service stop (not

provided) to the chiller. Turn on the water supply and flush

the line thoroughly.

Caution: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

4. Make connection between remote chiller outlet tube

and solenoid valve assembly. Outlet port is marked on

the chiller (1/4 O.D. copper tube). Install a 1/4 union

(provided) on the marked chiller outlet port. Insert one end of

1/4 poly tubing into the union and the other end into the

straight fitting on the solenoid valve assy (See Fig. 3)

5. Hang the upper panel on the mounting frame hanger. Be

sure that the panel is engaged with hanger at the top of

frame before releasing it. Align holes in the panel with holes

in the mounting frame. Install two (2) #10-24 x 5/8 (16mm)

screws (Item 27 - Figure 4) in holes and tighten securely.

98004C (REV. A - 9/04)

ENOB8C

Figure 4 - Upper Panel Installation

Figure 5 - Fountain Installation

Figure 6 - Lower Panel Installation

View From Rear

6. Install the fountain. Remove the screw (Item 28) from cover

plate (Item 12) and slide cover plate toward basin. Mount the

fountain to the upper panel and frame with (4) 5/16 x 1

(25mm) long bolts (Item 30), bracket (Item 34) and nuts

(Item 33) provided. Tighten securely. Brackets (Item 34)

must be installed as shown to properly support

fountain. (See Figure 5)

7. Attach waste tube (1-1/4 O.D.) to 1-1/4 O.D. slip

trap (provided by others).

8. Connect the fountain drain waste tube to the building

sanitary sewer system. Connection should be made in

compliance with local plumbing code requirements. (Note:

Plumbing trap is not included with the fountain).

9. Make connection between solenoid valve assembly

and fountain(s). Insert the 1/4 poly tubing coming from the

fountain with sensor into the solenoid valve. (See Fig. 3)

10. Connect power cord of sensor to solenoid valve

assembly by running it through the back panel and

connecting it to termianl shown in Fig. 8.

11. Turn on water supply and check for leaks. Release air

from tank by interrupting infrared beam; a steady stream of

water assures all air is removed. The sensor has a 30 second

maximum ON time. It may be necessary to step away from

beam a few times to allow chiller tank to fill.

DO NOT SOLDER tubes while

inserted into the strainer as damage

to o-rings may result.

12. These products are designed to operate on 20-105

PSIG supply line pressure. If inlet pressure is above 105

PSIG, a pressure regulator must be installed in the supply line.

Any damage caused by connecting

these products to a supply line with

pressure lower than 20 PSIG or

higher than 105 PSIG IS NOT covered

under warranty.

13. Make electrical connections to the chiller. See chiller

instructions.

14. Check stream height from bubbler. Stream height is

factory set at 35-40 PSI. If supply pressure varies greatly from

this, please do the following. For Electronic sensor units

only, remove lower panel (Item 26 - Fig. 6) and turn adjustment

screw on the regulator (Item 17 - Fig. 8). Clockwise adjustment

will raise stream height and counterclockwise movement will

lower stream height. For best adjustment stream should hit

basin approximately 6-1/2 from the bubbler.

15. Mount lower panel. Loosen the two (2) #10-24 x 5/8

(16mm) screws (Item 27 - Figure 5) at frame bottom lip. Slide

upper tongue of lower panel (Item 26 - Figure 6) under lower

edge of already installed upper panel. Tighten previously

loosened screws securely. (See Figure 6)

ENOB8C

98004C (REV. A - 9/04)

40, 41, 42

Figure 7 - Solenoid Assembly

Figure 8 - Regulator Assembly

CONNECTTO FOUNTAIN

SENSOR WIRING CONNECTOR

98004C (REV. A - 9/04)

ENOB8C

See Fig. 10

BUBBLER DETAIL

NOTE:

When installing replacement bubbler and pedestal,

tighten nut (Item 5) only to hold parts snug in

position. Do Not Overtighten.

Basin

Figure 9 - Exploded View

Figure 10 - Bubbler Assembly

ENOB8C

98004C (REV. A - 9/04)

Figure 11  Water Supply Connections

NOTE: WATER FLOW

DIRECTION SERVICE STOP

(NOT FURNISHED)

BUILDING WATER INLET

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

1/4" O.D. TUBE

WATER INLET

TO COOLER

Figure 12  Quick Connect Fittings

Actuation of Quick Connect Water Fittings: Cooler is provided with lead-

free connectors which utilize an o-ring water seal. To remove tubing from the fitting,

relieve water pressure, push in on the gray collar while pulling on the tubing. (See

Figure 12) To insert tubing, push tube straight into fitting until it reaches a positive stop

(approximately 3/4).

98004C (REV. A - 9/04)

ENOB8C

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484

Installation Package

The components for installation are packed in three

separate boxes, regardless of the type of unit being

installed. The boxes contain the following:

Box No. 1: Wall Frame(s)

Box No. 2: Remote Chiller, ECH8

Box No. 3: Fountain Arm and Panels

Additional materials, as noted in the Parts List, are also

shipped in these boxes.

PARTS LIST

ITEM NO. PART NO. DESCRIPTION

56073C

40322C

56011C

55997C

75580C

15027C

28454C

28455C

28474C

28473C

45767C

28343C

36207C

36193C

45813C

50986C

61315C

31376C

56163C

45769C

45768C

56092C

70683C

55996C

28382C

26833C

111008343890

70432C

38417001

75560C

40045C

70817C

70020C

28395C

50203C

56082C

56204C

70022C

70644C

31272C

70817C

75507C

Bubbler Assy

Assy -Orifice

Housing Assembly

Pedestal

Bubbler Locknut

Brkt - Swirlflow

Brkt - Solenoid/Reg/Wire

Assy - Brkt Solenoid/Reg/Wire

Basin - Swirlflow

Lower Shell

Fountain Body

Cover Plate

Wire - Extension

Assy - Sensor Eye

Sleeve - Swirlflow EE

Holder - Regulator

Regulator

Cord - Power 115v

Gasket - Drain

Assy - Drain/Tailpipe

Drain - Plug 1-1/2

Poly Tubing (Cut To Length)

Fitting - Union 1/4 x 1/4

Strainer (Provided With Chiller)

Back Panel

Lower Panel

Screw - #10-24 x .62 HHMS

Screw - #8-32 x .38 THTC

Screw - #8-18 x .37 HHSM

Screw - 5/16-18 x 1.00 HHMS

Nut - Hex 1 5/16

Fttng - Elbow 1/4 x 1/4

Nut - Hex 5/16-18

Bracket - Support

Bushing - Strain Relief

Nut - Regulator

Lens - Swirlflow EE

Screw - #6-32 x .31 Set

Screw - #6-32 x .50 PHMS

Solenoid Valve

Fttng-Elbow 1/4 Stem x 1/4x90

Fttng-1/4 NPTF x 1/4OD

1. Orifice Assy: Minerals deposits on orifice can cause water flow to

spurt or not regulate. Mineral deposits may be removed

from the orifice with a small round file not over 1/8" diameter or a

small diameter wire. CAUTION: Do not file or cut orifice materials.

2. Stream Regulator: If orifice is free of material deposits regulate

water flow according to instructions on page 4.

3. Sensor Control: The sensor has a 2 second delay time. If sensor

fails to operate valve mechanism or operates erratically, check

the following:

a) Ensure there are no obstructions within a 40 inch radius from

the front of fountain.

b) Check wire connections at the solenoid valve and at the sensor.

CAUTION: Make sure unit is unplugged before checking any

wiring.

c) Ensure proper operation of solenoid valve. If there is an audible

clicking sound yet no water flows, look for an obstruction in the

valve itself or elsewhere in the water supply line.

WARNING: Do not expose sensor to direct sunlight.

4. Sensor Range Adjustment: The electronic sensor used in this

fountain is factory pre-set for a "visual" range of 36 inches. If

actual range varies greatly from this, or a different setting is desired,

follow the range adjustment procedure below:

a) Remove front lens.

b) Locate range adjustment screw between the lenses of the

sensor, then with a small tip screwdriver, rotate the range adjust-

ing screw clockwise to increase range or counter-clockwise to

decrease range. 1/4 turn of screw is equal to approximately

12 - 18 inches of range.

CAUTION: Complete range of sensor (24 - 46 inches) is only one

turn of the adjusting screw.

c) Replace Lens.

CARE AND CLEANING INSTRUCTIONS

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620

TROUBLE SHOOTING AND MAINTENANCE

DO NOT use abrasive or chemical cleaners to clean the sensor lens.

They may dull the luster and attack the plastic cover and chrome

finish of the fountain. Use ONLY soap and water, then wipe with

clean cloth or towel. When cleaning adjacent surfaces, the fountain

and the sensor lens should be protected from any splattering of

cleaners. Acid and cleaning fluids can discolor and damage chrome

plating and plastic sensor lens.

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay EDFPVR217RC Installationshandbuch

Elkay

Elkay SWIRLFLO ENOBM28K Gebrauchsanweisung

Elkay

Elkay SWIRLFLO EDFPBWM114C Gebrauchsanweisung

Elkay

Elkay Soft Sides LCRSPD10-2AQ Installationshandbuch

Elkay

Elkay Soft Sides ECDFPW314FPC Installationshandbuch

Elkay

Elkay EFRP12CDC_2 Installationshandbuch

Elkay

Elkay 4420BF1LDB Series Bedienungsanleitung

Elkay

Elkay Soft Sides ECDFPW314C Gebrauchsanweisung

Elkay

Elkay Soft Sides ERFP8C B Series Installationshandbuch

Elkay

Elkay Soft Sides EDFP217FP B Series Bedienungsanleitung

Elkay

Elkay Endura II 4405BFEVGWR Installationshandbuch

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay LK4400 Bedienungsanleitung

Elkay

Elkay Hydroboost HTHBHAC8BLSSWF25N Installationshandbuch

Elkay

Elkay LK4410BFFR FTN A Series Bedienungsanleitung

Elkay

Elkay VRCTL 8 1D Series Installationshandbuch

Elkay

Elkay Slimline EHWM14C A Series Bedienungsanleitung

Elkay

Elkay SWIRLFLO ENOB8C Gebrauchsanweisung

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Elkay

Elkay SOFT SIDES EDFP217WS F Series Gebrauchsanweisung

Elkay

Elkay 4405BFFR Bedienungsanleitung

Elkay

Elkay FLEXI-GUARD EIOA4 1E Series Installationshandbuch

Elkay

Elkay EDFPW210C Installationshandbuch

Elkay

Elkay SWIRLFLO Series Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung