Elkay SWIRLFLO Series Installationshandbuch

98005C (REV. B - 3/05)

SWIRLFLO Refrigerated fountains with FLEXI-GUARD

INSTALLATION, CARE & USE MANUAL

TM TM

ENOB2-8C ENOB2-8RAC

Reviewtheseinstructionsbeforebeginninginstallation.Besurethatinstallation

conformsto all plumbing, electrical andother applicable codes.

When installation is complete, ensure these instructions are left with building owner

for future reference.

Servicetobeperformedbyauthorizedservicepersonnelonly.

INSTALLER

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to

availablewater lines.This can,however, cause electrical feedback inthe plumbing circuit, which resultsin

an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic taste to it or

has a noticeable increase in the metallic content of the water.

When inspecting plumbing circuit, remember the line may be grounded some distance from the installation,

and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.Any

drainfittingsprovidedbytheinstallershould be made of plastic which will electronically isolate thefountain

fromtheremainderofthebuilding’splumbingcircuits.

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05) 2

33 15/16"

863mm

41 11/16"

1059mm

1 5/8"

41mm

1 5/8"

41mm

5/8"

16mm

12"

305mm

1 1/8"

29mm

11"

279mm

4 1/2"

114mm

203mm

28 3/4"

730mm

36 1/2"

927mm

FINISHED FLOOR

MINIMUM DEPTH

BACK WALL LINE

B18 3/4"

476mm

9 3/8"

238mm

8 1/8"

206mm

1 1/8"

29mm

3 1/8"

80mm

18 3/8"

467mm

27"

686mm

ADA

REQUIREMENT

LEGEND

A = 1/4” O.D. Tube - Water Outlet Connection

B = 3/8” O.D. Tube - Water Inlet Connection

C = 1-1/4” Waste Tube

D = ELECTRICAL INLET

1 1/8"

29mm

11"

279mm

203mm

4 1/2"

114mm

28 3/4"

730mm

12"

305mm

5/8"

16mm

41 11/16"

1060mm

33 15/16"

863mm

1 5/8"

41mm

1 5/8"

41mm

36 1/2"

926mm

FINISHED FLOOR

MINIMUM DEPTH

18 3/4"

476mm

9 3/8"

238mm

8 1/8"

206mm

1 1/8"

29mm

3 1/8"

79mm

18 3/8"

467mm

27"

686mm

ADA

REQUIREMENT

BACK WALL LINE

Figure 1 - Rough-in Dimensions

Model ENOB2-8C Model ENOB2-8RAC

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05)

1. Install chiller: Remove front panel of chiller. Slide chiller onto

the shelf and position it to the left as per dimensions

in Figure 1.

Note: Building construction must allow for

adequate air flow on both sides, top and

back of chiller. A minimum of 4” (102mm) on

both sides and top is required. See chiller

installation for additional instructions.

2. Attach solenoid valve assembly to the underside of

cross member of mounting frame on electronic

sensor unit. (See Fig. 7).

3. Make water supply connections. Inlet port is marked on

the chiller (1/4” O.D. copper tube). Bend the copper tube

(provided) at an appropriate length from the chiller to

opening in frame. Install the in-line strainer (provided with

chiller) by pushing it in until it reaches a positive stop,

approximately 3/4” (19mm) on the marked chiller inlet port

(See Figs. 3) (Refer to Fig. 13 on page 7 for details on

assembling quick connect fittings). Attach an unplated and

deburred copper water inlet line and a service stop (not

provided) to the chiller. Turn on the water supply and flush

the line thoroughly.

Caution: DO NOT SOLDER tubes inserted

into the strainer as damage to

o-rings may result.

4. Make connection between remote chiller outlet tube

and solenoid valve assembly. Outlet port is marked on

the chiller (1/4” O.D. copper tube). Install a 1/4” tee

(provided) on the marked chiller outlet port. Insert one end of

1/4” poly tubing into the tee and the other end into the

straight fitting on the solenoid valve assy. (See Fig. 3)

5. Hang the upper panel on the mounting frame hanger. Be

sure that the panel is engaged with hanger at the top of

frame before releasing it. Align holes in the panel with holes

in the mounting frame. Install two (2) #10-24 x 5/8” (16mm)

screws (Item 27 - Figure 4) in holes and tighten securely.

6. Install the fountain. Remove the screw (Item 28) from cover

plate (Item 12) and slide cover plate toward basin. Mount the

fountain to the upper panel and frame with (4) 5/16” x 1”

(25mm) long bolts (Item 30), bracket (Item 34) and nuts

(Item 33) provided. Tighten securely. Brackets (Item 34)

must be installed as shown to properly support

fountain. (See Fig. 5)

Special Tools

Item Description Quantity

NONE

Additional Materials

Item Description Quantity

1 Unplatedcopper inlet pipe

2 ServiceStop

REQUIREDTOOLSANDMATERIALS

These tables show special tools and/or

additional materials (not provided) which are

necessary to complete installation of these

units:

Figure 2 - Chiller Installation

CHILLER

INLET

CHILLER

OUTLET

TOBUBBLER

Figure 3 - ENO Tube Routing

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05) 4

Figure 4 - Upper Panel Installation

Figure 5 - Fountain Installation

Figure 6 - Lower Panel Installation

7. Attach waste tube (1-1/4” O.D.) to 1-1/4” O.D. slip

trap (provided by others).

8. Connect the fountain drain waste tube to the building

sanitary sewer system. Connection should be made in

compliance with local plumbing code requirements. (Note:

Plumbing trap is not included with the fountain).

9. Make connection between solenoid valve assembly

and fountain(s). Insert the 1/4” poly tubing coming from the

fountain with sensor into the solenoid valve. Insert the 1/4”

poly tubing coming from the fountain with push button into the

tee (See Fig. 3).

10. Connect power cord of sensor to solenoid valve

assembly by running it through the back panel and

connecting it to terminal as shown in Fig. 8.

11. Turn on water supply and check for leaks. Release air

from tank by interrupting infrared beam; a steady stream of

water assures all air is removed. The sensor has a 30 second

maximum ON time. It may be necessary to step away from

beam a few times to allow chiller tank to fill.

DO NOT SOLDER tubes while

inserted into the strainer as damage

to o-rings may result.

12. These products are designed to operate on 20-105

PSIG supply line pressure. If inlet pressure is above 105

PSIG, a pressure regulator must be installed in the supply line.

Any damage caused byconnecting

these products to a supply line with

pressure lower than 20 PSIG or

higher than 105 PSIG IS NOT covered

under warranty.

13. Make electrical connections to the chiller. See chiller

instructions.

14. Check stream height from bubbler. Stream height is

factory set at 35-40 PSI. If supply pressure varies greatly from

this, please do the following. For Push Button units only,

remove push button (Item 14 - Figure 12) and adjust the

screw on the regulator (Item 16 - Figure 12). To remove push

button, remove set screw from bottom of

sleeve (Item 31). Insert a small punch in screw hole and

push up while grasping the push button and pull forward

removing the push button. Clockwise adjustment will raise

stream height and counterclockwise movement will lower

stream height. For best adjustment stream

should hit basin approximately 6-1/2” from the bubbler.

Reassemble push button by pushing in on button until the push

button catches in the sleeve. Reinstall the set

screw (Item 31) in the sleeve (Item 12).

For Electronic sensor units only, remove lower

panel (Item 26 - Fig. 4) and turn adjustment screw on the

regulator (Item 16 - Fig. 8). Clockwise adjustment will raise

stream height and counterclockwise movement will lower

stream height. For best adjustment stream should hit basin

approximately 6-1/2” from the bubbler.

15. Mount lower panel. Loosen the three (3) #10-24 x 5/8”

(16mm) screws (Item 27 - Figure 5) at frame bottom lip. Slide

upper tongue of lower panel (Item 26 - Figure 6) under lower

edge of already installed upper panel. Tighten previously

loosened screws securely. (See Figure 6)

24, 25

View From Rear

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05)

45, 46, 47

ENOB2-8C

Figure 8 - Regulator Assembly

Figure 7 - Solenoid Assembly ENOB2-8RAC

CONNECTTOFOUNTAIN

SENSORWIRINGCONNECTOR

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05) 6

See Fig. 10

BUBBLERDETAIL

NOTE:

When installing replacement bubbler and pedestal,

tighten nut (Item 5) only to hold parts snug in

position. Do Not Overtighten.

Basin

Figure 9 - Exploded View

Figure 10 - Bubbler Assembly

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05)

Figure 11 - Fountain Body Assembly

Figure 12 - Push Button Assembly

14 15

See Fig. 10

Figure 14 – Water Supply Connections

NOTE: WATER FLOW

DIRECTION SERVICE STOP

(NOT FURNISHED)

BUILDING WATER INLE

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

/4" O.D. TUBE

WATER INLET

TO COOLER

Figure 13 – Quick Connect Fittings

Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors

whichutilizean o-ringwaterseal.Toremovetubing fromthefitting, relievewaterpressure, pushin

onthe gray collarwhile pulling onthe tubing.(SeeFigure 13)Toinsert tubing,pushtube straight

intofittinguntilitreachesapositivestop(approximately3/4”).

ENOB2-8C,ENOB2-8RAC

98005C (REV. B - 3/05) 8

PARTSLIST

ITEMNO. PARTNO. DESCRIPTION

56073C

40322C

56011C

55997C

75580C

15027C

28455C

28474C

28473C

45767C

28343C

45781C

45847C

45848C

50986C

61315C

15005C

56163C

45769C

45768C

56092C

70682C

55996C

28383C

28384C

27026C

111008343890

70432C

38417001

75560C

75632C

70817C

70020C

28395C

36207C

36193C

45813C

31376C

40045C

50203C

56082C

56204C

70022C

70644C

31272C

70817C

75507C

28454C

75671C

Bubbler Assy

Orifice Assy

Housing Assembly

Pedestal

Bubbler Locknut

Brkt - Swirlflow

Assy - Brkt Solenoid/Reg/Wire

Basin - Swirlflow

Lower Shell

Fountain Body

CoverPlate

Sleeve

Pin - Push Button

Push Button

Holder - Regulator

Regulator

RetainingNut

Gasket - Drain

Assy - Drain/Tailpipe

Drain - Ferrule

Poly Tubing (Cut To Length)

Tee - 1/4

Strainer (Provided with Chiller)

Back Panel RHADA

Back Panel LHADA

Lower Panel

Screw - #10-24 x .62 HHSM

Screw - #8-32 x .38 THSM

Screw - #8-18 x .37 HHSM

Screw - 5/16-18 x 1.00 HHMS

Setscrew - #10-32 x .31

Fttng - Elbow 1/4 x 1/4

Nut - Hex 5/16-18

Bracket - Support

Wire - Extension

Assy - Sensor Eye

Sleeve - Swirlflow EE

Cord - Power 115v

Nut - Hex 1 5/16

Bushing - Strain Relief

Nut - Regulator

Lens - Swirlflow EE

Screw - #6-32 x .31 Set

Screw - #6-32 x .50 PHMS

Solenoid Valve

Fttng-Elbow 1/4 Stem x 1/4x90

Fttng-1/4NPTF x 1/4OD

Brkt -Solenoid/Reg Swirlflo

Spring - Push Button

InstallationPackage

The components for installation are packed in three

separate boxes, regardless of the type of unit being

installed. The boxes contain the following:

Box No. 1: Wall Frame(s)

Box No. 2: Remote Chiller, ECH8

Box No. 3: Fountain Arm and Panels

Additional materials, as noted in the Parts List, are also

shipped in these boxes.

1. Orifice Assy: Minerals deposits on orifice can cause water flow to

spurt or not regulate. Mineral deposits may be removed

from the orifice with a small round file not over 1/8" diameter or a

small diameter wire. CAUTION: Do not file or cut orifice materials.

2. Stream Regulator: If orifice is free of material deposits regulate

water flow according to instructions on page 4.

3. Sensor Control: The sensor has a 2 second delay time. If sensor

fails to operate valve mechanism or operates erratically, check

the following:

a) Ensure there are no obstructions within a 40 inch radius from

the front of fountain.

b) Check wire connections at the solenoid valve and at the sensor.

CAUTION: Make sure unit is unplugged before checking any

wiring.

c) Ensure proper operation of solenoid valve. If there is an audible

clicking sound yet no water flows, look for an obstruction in the

valve itself or elsewhere in the water supply line.

WARNING: Do not expose sensor to direct sunlight.

4. Sensor Range Adjustment: The electronic sensor used in this

fountain is factory pre-set for a "visual" range of 36 inches. If

actual range varies greatly from this, or a different setting is desired,

follow the range adjustment procedure below:

a) Remove front lens.

b) Locate range adjustment screw between the lenses of the

sensor, then with a small tip screwdriver, rotate the range adjust-

ing screw clockwise to increase range or counter-clockwise to

decrease range. 1/4 turn of screw is equal to approximately

12 - 18 inches of range.

CAUTION: Complete range of sensor (24 - 46 inches) is only one

turn of the adjusting screw.

c) Replace lens.

TROUBLESHOOTINGANDMAINTENANCE

CARE ANDCLEANING INSTRUCTIONS

DO NOT use abrasive or chemical cleaners to clean the sensor lens.

They may dull the luster and attack the plastic cover and chrome

finish of the fountain. Use ONLY soap and water, then wipe with

clean cloth or towel. When cleaning adjacent surfaces, the fountain

and the sensor lens should be protected from any splattering of

cleaners. Acid and cleaning fluids can discolor and damage chrome

plating and plastic sensor lens.

ENOB2-8C,ENOB2-8RAC

www.DrinkingFountainDoctor.com 800-518-5388

Andere Handbücher für SWIRLFLO Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay EFRP8C Installationshandbuch

Elkay

Elkay SWIRLFLO Series Gebrauchsanweisung

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay SWIRLFLO Series Installationshandbuch

Elkay

Elkay 4420BF1UDB Series Bedienungsanleitung

Elkay

Elkay Composite VR Fountain EDFPVR217RC Gebrauchsanweisung

Elkay

Elkay LK4420SFRK Bedienungsanleitung

Elkay

Elkay SOFT SIDES EZLMSN-EDFPVM217DK Gebrauchsanweisung

Elkay

Elkay 4400BF Bedienungsanleitung

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay ERPA2-8C*A Installationshandbuch

Elkay

Elkay EDFPA17FPC Installationshandbuch

Elkay

Elkay SWIRLFLO ENOB28K Gebrauchsanweisung

Elkay

Elkay SWIRLFLO FLEXI-GUARD ERPB8C 2C Series Installationshandbuch

Elkay

Elkay ERO28C*C Installationshandbuch

Elkay

Elkay SWIRLFLO ENOB2-8RAC Gebrauchsanweisung

Elkay

Elkay EHW214C A Series Installationshandbuch

Elkay

Elkay FLEXI-GUARD ESRC8 3GJO Series Installationshandbuch

Elkay

Elkay Soft Sides ECDFPW314C Gebrauchsanweisung

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay EHWM214C*A Installationshandbuch

Elkay

Elkay Soft Sides Series Installationshandbuch

Elkay

Elkay 4420FR FTN A Series Bedienungsanleitung

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung