Elkay SWIRLFLO Series Installationshandbuch

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

97921C (REV. C - 3/05)

Page 1

SWIRLFLO fountains with FLEXI-GUARD

INSTALLATION, CARE & USE MANUAL

TM TM

!CAUTION

Reviewtheseinstructionsbeforebeginninginstallation.Besurethatinstallation

conformsto all plumbing, electrical and other applicable codes.

WARNING

When installation is complete, ensure these instructions are left in the plastic bag

providedinside the installedunit for futurereference.

!WARNING

Serviceto be performedbyauthorized service personnelonly.

INSTALLER

NOTE: It is commonpractice to ground electrical hardware such as telephones, computers and other devices

toavailablewater lines.Thiscan, however,causeelectrical feedback in the plumbing circuit, which

results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic

taste to it or has a noticeable increase in the metallic content of the water.

Wheninspecting plumbing circuit, remember the line may be groundedsome distance from the

installation, and may occur outside the building or area in which the unit is being installed.

This condition can be avoided (in most cases) by using recommended materials during installation.Any

drain fittings provided by theinstaller should be made of plastic whichwill electronically isolate the

fountainfrom the remainder of the building’splumbingcircuits.

EDFPB114C EDFPBWM114C

97921C (REV. C - 3/05)

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

Page 2

LEGEND

A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.

B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind

Wall. 1-1/4” O.D. Drain (Trap Not Furnished)

C = Opening For Optional AP-99 Access Panel

Figure 2 - Rough-in Assembly For EDFPB114C

Figure 1 - Rough-in for EDFPB114C W/MP86 Mounting Plate

Optional

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

97921C (REV. C - 3/05)

Page 3

LEGEND

A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.

B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind

Wall. 1-1/4” O.D. Drain (Trap Not Furnished)

C = Opening For Optional AP-99 Access Panel

NOTE: Reinforce The Wall In The Shaded Areas

Figure 4 - Rough-in Assembly for EDFPBWM114C

Figure 3 - Rough-in for EDFPBWM114C

Optional

97921C (REV. C - 3/05)

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

EDFPB114C Installation

1. Wall should already be framed for the fountain using

the positioning dimensions shown in Figure 1. Shown

dimensions pertain to installation location (framing

must support up to 300 lbs. weight). These

dimensions are required for compliance with ANSI

StandardA117.0.

2. Install rough-in plumbing as shown in Figure 1. Run

supply water inlet line through the back panel. Install a

service stop (not provided). Turn on supply water and

flush thoroughly.

3. Install fountain. Remove screw (Item 28) from cover

plate and slide cover plate (Item 14) toward basin.

Mount the fountain to the wall and mounting plate with

(4) 5/16” hex nuts (provided with mounting plate).

Tighten securely. (See Figure 5)

4. Determine required length of waste line and cut to

appropriate length. 1-1/4” O.D. waste tube furnished.

1-1/4” slip trap, waste elbow and extension not

provided.

5. Make water supply connections from service stop to

the 3/8” O.D. unplated copper tube coming out of the

strainer. Turn on water supply and check for leaks

(See Figure 14). Newly installed water supply line

should be insulated after leak check is completed.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to the

o-rings may result.

6. These products are designed to operate on

20-105 PSIG supply line pressure. If the inlet

pressure is above 105 PSIG, a pressure regulator

must be installed in the supply line. Any damage

caused by reason of connecting these products to

supply line pressures lower than 20 PSIG or higher

than 105 PSIG is not covered by warranty.

7. Check stream height from bubbler. Stream height is

factory set at 35 PSI. If supply pressure varies

greatly from this, remove push button (Item 17 -

Figure 12) and adjust the screw on the regulator

(Item 19 - Figure 12). To remove push button,

remove setscrew from bottom of sleeve (Item 15).

Insert a small punch in screw hole and push

up while grasping the push button and pull forward

removing the push button. Clockwise adjustment

will raise stream height and counterclockwise

movement will lower stream height. For best

adjustment stream should hit basin approximately

6-1/2” from the bubbler. Reassemble push button

by pushing in on button until the push button

catches in the sleeve. Reinstall the setscrew

(Item 31) in the sleeve (Item 15).

Page 4

Figure 5 - EDFPB114C Fountain Installation

Figure 6 - AP-99 Panel (Optional)

5/16” Studs - Supplied with MP86

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

97921C (REV. C - 3/05)

Figure 7 - EDFPBWM114C Panel Installation

Figure 8 - EDFPBWM114C Fountain Installation

EDFPBW114C Installation

1. Wall should already be framed for the fountain using

the positioning dimensions shown in Figure 3. Shown

dimensions pertain to installation location (framing

must support up to 300 lbs. weight). These dimensions

are required for compliance with ANSI Standard A117.0.

2. Install rough-in plumbing as shown in Figure 3. Run

supply water inlet line through the back panel. Install a

service stop (not provided). Turn on supply water and

flush thoroughly.

3. Install back panel. Place the upper edge of the panel

above mounting plate on the wall. Slide the panel down

until it engages the mounting plate. Be sure back panel

is firmly engaged before releasing it. (See Figure 7)

4. Install fountain. Remove screw (Item 28) from cover

plate and slide cover plate (Item 14) toward basin. Mount

the fountain to the back panel and mounting plate with (4)

5/16” x 1” (25mm) long screws (Item 30 - provided).

Tighten securely. (See Figure 8)

5. Determine required length of waste line and cut to

appropriate length. 1-1/4” O.D. waste tube furnished.

1-1/4” slip trap, waste elbow and extension not provided.

6. Make water supply connections from service stop to

the 3/8” O.D. unplated copper tube coming out of the

strainer. Turn on water supply and check for leaks

(See Figure 14). Newly installed water supply line

should be insulated after leak check is completed.

CAUTION: DO NOT SOLDER tubes inserted

into the strainer as damage to the

o-rings may result.

7. These products are designed to operate on 20-105

PSIG supply line pressure. If the inlet pressure is

above 105 PSIG, a pressure regulator must be

installed in the supply line. Any damage caused by

reason of connecting these products to supply line

pressures lower than 20 PSIG or higher than

105 PSIG is not covered by warranty.

8. Check stream height from bubbler. Stream height is

factory set at 35 PSI. If supply pressure varies

greatly from this, remove push button (Item 17 -

Figure 12) and adjust the screw on the regulator

(Item 19 - Figure 12). To remove push button,

remove setscrew from bottom of sleeve (Item 15).

Insert a small punch in screw hole and push up

while grasping the push button and pull forward

removing the push button. Clockwise adjustment

will raise stream height and counterclockwise

movement will lower stream height. For best

adjustment stream should hit basin approximately

6-1/2” from the bubbler. Reassemble push button

by pushing in on the button until the push buttom

catches in the sleeve. Reinstall the setscrew

(Item 31) in the sleeve (Item 15).

Figure 9 - AP-99 Panel (Optional)

Page 5

97921C (REV. C - 3/05)

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

Page 6

BUBBLERDETAIL

VANDALRESISTANT

BUBBLERDETAIL

NOTE:

When installing replacement bubbler and pedestal, tighten

nut (Item 7) only to hold parts snug in position. Do Not

Overtighten.

Figure 10 - Bubbler Details

BASIN

2, 3, 4

BASIN

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

97921C (REV. C - 3/05)

Page 7

Figure 11 - Fountain Body

Figure 12 - Push Button

17 18

See Fig. 10 23

See Fig. 10

97921C (REV. C - 3/05)

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C

PARTSLIST

ITEMNO. PARTNO. DESCRIPTION

56073C

40319C

50171C

50314C

56011C

55997C

75580C

98118C

100322740560

15009C

55001132

55000944

45767C

28343C

45781C

45847C

45848C

50986C

61313C

15005C

56163C

45769C

45768C

56092C

28397C

55000955

111008343890

70432C

38417001

75560C

75632C

70817C

55996C

75671C

Bubbler Assy

Fitting - Orifice

O-Ring

Orifice - Flow Straightener

Housing Assembly

Pedestal

Bubbler Locknut

Body - Bubbler VR

Gasket - Black .68 x 1.03 VR

Nipple - Bubbler VR

Basin - Swirlflow

Lower Shell

Fountain Body

CoverPlate

Sleeve

Pin - Push Button

Push Button

Holder - Regulator

Regulator

RetainingNut

Gasket - Drain

Assy - Drain/Tailpipe

Plug - Drain 1-1/2”

Poly Tubing (Cut To Length)

BackPanel

AP-99 Panel (Optional)

Screw - #10-24 x .62 HHMS

Screw - #8-32 x .38 THSM

Screw - #8-18 x .37 HHSM

Screw - 5/16-18 x 1.00 HHMS

Setscrew - #10-32 x .31

Fttng - Elbow 1/4 x 1/4

Strainer

Spring - Push Button

TROUBLESHOOTING& MAINTENANCE

Orifice Assembly: Mineraldeposits on orifice

can cause water flow to spurt or not regulate. Mineral

depositsmay be removed from the orifice by poking

with a small round file not over 1/8” diameter, or using a

smalldiameter wire.

CAUTION

DO NOT file or cut orifice

material.

Stream Regulator: If orifice is clean, regulate

flow as in Step 7, Page 4 or Step 8, Page 5 of the

installation instructions. If replacement is necessary,

see parts list for correct regulator part number.

Actuation of Quick Connect Water Fittings:

Cooleris provided with lead-free connectorswhich

utilizean o-ring water seal.Toremove tubing from the

fitting,relieve water pressure, push in on the gray

collarwhile pulling on the tubing. (See Figure 13)To

insert tubing, push tube straight into fitting until it

reachesapositivestop (approximately3/4”).

Figure 13 – Quick Connect Fittings

Figure 14 - Water Supply Connections

Page 8

NOTE: WATER FLOW

DIRECTION SERVICE STOP

(NOT FURNISHED)

BUILDING WATER INLE

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

/4" O.D. TUBE

WATER INLET

TO COOLER

PRINTED IN U.S.A.

www.DrinkingFountainDoctor.com 800-518-5388

Andere Handbücher für SWIRLFLO Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay EDFP19C series Installationshandbuch

Elkay

Elkay Endura II 4405BFEVGWR Installationshandbuch

Elkay

Elkay EHWM214C*A Installationshandbuch

Elkay

Elkay Soft Sides ERO8C C Series Installationshandbuch

Elkay

Elkay Soft Sides ERFPD8C Installationshandbuch

Elkay

Elkay 4430 Bedienungsanleitung

Elkay

Elkay Hydroboost HTHBHAC8BLSSWF25N Installationshandbuch

Elkay

Elkay Soft Sides FLEXI-GUARD ERO28C C Series Installationshandbuch

Elkay

Elkay EZS8WS 1F Series Gebrauchsanweisung

Elkay

Elkay Swirlflo EDFPBW114FP Bedienungsanleitung

Elkay

Elkay LVRCTL8 1D Series Installationshandbuch

Elkay

Elkay ERPA2-8C Installationshandbuch

Elkay

Elkay ERPA8C*A Installationshandbuch

Elkay

Elkay HEWD K Series Installationshandbuch

Elkay

Elkay 4420 Series Bedienungsanleitung

Elkay

Elkay LK4400 Bedienungsanleitung

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Elkay

Elkay 4430FR Bedienungsanleitung

Elkay

Elkay FGDF710-10-1H-MDN Installationshandbuch

Elkay

Elkay Soft Sides ERO28C B Series Installationshandbuch

Elkay

Elkay SWIRLFLO FLEXI-GUARD ENOBM8C Installationshandbuch

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay LK4430ORN Bedienungsanleitung

Elkay

Elkay LVRCTL8S-BAC Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung