Elkay Soft Sides ERO28C B Series Installationshandbuch

97114C (Rev. G - 07/01)

ERO28C*B ERO28RAC*B

Installation/Care/Use Manual

Soft SidesRefrigerated Fountains with FLEXI-GUARD®

To assure you install this model easily and correctly,

PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE

INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH

PLUMBING, ELECTRICALAND OTHER APPLICABLE CODES. After installation, leave

these instructions inside the fountain for future reference.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO

WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY

OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK

INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN

INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING

THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER

SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING

PLUMBING SYSTEM.

FIG. 2FIG. 1

Installer

NOTE: WATER FLOW

DIRECTION

BUILDING WATER

INLET

SERVICE STOP

(NOT FURNISHED)

1/4" O.D. TUBE

WATER INLET

TO COOLER

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

SEE FIG. 7

ERO28C ERO28RAC

97114C (Rev. G - 07/01)

ERO28C*B ER028RAC*B

PAGE 2

FIG. 3

LEGEND

A = 3/8" O.D. TUBE CONNECT (CHILLER WATER OUTLET)

B = 3/8" O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS

C = 1-1/4" TRAP FURNISHED

D = ELECTRICAL INLET

ERO28C ERO28RAC

97114C (Rev. G - 07/01)

ERO28C*B ERO28RAC*B

PAGE 3

FIG. 4

INSTALLATION INSTRUCTIONS

FIG. 5

1. Install mounting frame. See mounting frame instructions.

2. Install remote chiller. Remove front panel of chiller. Slide chiller onto the shelf and position it to the left within the guides on the shelf.

3. Attach solenoid valve assy to the underside of cross member of mounting frame on electric eye unit. See Figure 9.

4. Make water supply connections. Install a shut-off valve and union connection to building water supply (valve and union not provided). Turn on the

water supply and flush the line thoroughly.

5. Make connection between remote chiller and building supply line. Remove the 3/8" x 1/4" union from the chiller inlet tube and install it on the water

inlet line of the upper fountain. Install the strainer on the chiller inlet tube. Install a 3/8" O.D unplated copper water line between the valve and the

cooler. Remove all burrs from the outside of the water line. Insert the 3/8" water line into the inlet side of the strainer by pushing it in until it reaches

a positive stop, approximately 3/4" (19mm). See Figures 2 and 4. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE

O-RINGS MAY RESULT.

6. Make connection between remote chiller and solenoid valve assy. Install the 3/8" tee (provided) on the chiller outlet tube. Install the 3/8" stem x 1/4"

O.D. tube union (provided) into 3/8" tee (See Fig. 4). Install 1/4" O.D. formed tube (provided) between 3/8" stem x 1/4" O.D. tube union and the

straight fitting on solenoid valve assy.

7. Hang the upper panel on the mounting frame hanger. Align holes in the panel with holes in the mounting frame. Be sure that panel is engaged with

hanger at top of frame before releasing it.

8. Install fountains. Remove bottom cover plates on underside of fountains and save the screws. Mount the fountains to the upper panel and the wall

frame with (4) 5/16" x 3/4" (19mm) long bolts and nuts (provided). Tighten securely.

9. Connect solenoid valve assy and regulator holder in fountain with sensor by installing 1/4" O.D. x 24" straight tube (provided). Connect fountain with

push button to chiller by installing 3/8" O.D. x 30' tube (provided). Insert one end into remaining outlet of the 3/8" tee and the other end into the 3/8"

x 1/4" union that was removed from the chiller inlet and attached to the water inlet line on push button fountain.

10. Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to required length using plumbing

hardware and trap as a guide.

11. Connect power cord of sensor to solenoid valve by running it through the back panel and connecting it as shown in Fig. 5. Connectors may be

connected to either terminal on solenoid valve. Attach ground wire to solenoid valve bracket with green ground screw.

12. Turn on water supply. Release air from tank by interrupting infrared beam; steady stream of water assures all air is removed. The sensor has a 30

second maximum ON time. It may be necessary to step away from beam a few times to allow chiller tank to refill. Check for leaks.

13. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be

installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSIG or higher than

105 PSIG is not covered by warranty.

14. Make electrical connections to chiller. See chiller instructions.

15. Check stream height from bubbler. Stream height is factory set at 35 PSI . If supply pressure varies greatly from this, remove items 28 and 36

and adjust the screw on the regulator (item 8). Clockwise adjustment will raise stream height and counter-clockwise will lower stream height. For best

adjustment stream height should hit basin approximately 6-1/2" (165mm) from the bubbler.

16. Mount lower panel. Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue of lower panel under lower edge of already

installed upper panel. Tighten previously loosened screws securely.

17. Replace bottom cover plate to fountain basin using screws provided. Tighten securely.

25 40

97114C (Rev. G - 07/01)

ERO28C*B ER028RAC*B

PAGE 4

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620

ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484

PART NO.ITEM NO.

PARTS LIST

DESCRIPTION

TROUBLE SHOOTING AND MAINTENANCE

Orifice Assy

Housing Assy

Pedestal

Bubbler Locknut

Drain

Retaining Nut

Regulator Holder

Regulator

Fountain Body-Short

Fountain Body-Long

Bottom Cover Plate-Short

Bottom Cover Plate-Long

Upper Panel

Lower Panel

Screw #8-32 X .38" TH

Strainer

Hex Nut

Speed Nut

Union-3/8 X 1/4

Regulator Mounting Bracket-Long Ftn

Solenoid Mounting Bracket

Regulator Mounting Bracket-Short Ftn

Sensor Support Mounting Bracket

Solenoid Valve Assy

Power Cord

Sensor Assy

Screw - #8-18 X .37 HHSM

Nut - Regulator

Hex Nut #10-32

Push Button

Push Button Sleeve

Strain Relief

Spacer - 1/2 X .44

Set Screw #6-32 X .31"

Screw - #10-24 X .38 PHTC

Screw - 1/4-20 X .38 HHTC

Elbow - 1/4 X 1/4

Tee - 3/8

Union - 3/8 Stem X 1/4 Tube

Fitting - 1/4 NPTF X 1/4 O.D.

Screw - #10-24 X .62 HHMS

Screw- 5/16-18 X .75

Hex Nut - 5/16-18

Poly Tubing (Cut To Length)

A54874

50934C

50168C

75580C

LK464

15005C

50986C

61313C

55000604

27623C

55000661

55000665

26839C

26833C

110711942550

55996C

40045C

70055C

70745C

22525C

22526C

27057C

27240C

31272C

31376C

31384C

38417001

56082C

70016C

45662C

45663C

50203C

51409C

70022C

70208C

70256C

70817C

70852C

75491C

75507C

111008343890

111577243890

111577343890

56092C

FIG. 7

FIG. 6

SEE FIG. 8

11, 15, 18

SEE FIG. 5

12, 15, 18

1. Orifice Assy: Minerals deposits on orifice can cause water flow to spurt or not

regulate. Mineral deposits may be removed from the orifice with a small round

file not over 1/8" diameter or a small diameter wire. CAUTION: Do not file or

cut orifice materials.

2. Stream Regulator: If orifice is free of material deposits regulate water flow

according to instructions on page 3.

3. Sensor Control: The sensor has a 2 second delay time. If sensor fails to

operate valve mechanism or operates erratically, check the following:

a) Ensure there are no obstructions within a 40 inch radius from the front of

fountain.

b) Check wire connections at the solenoid valve and at the sensor.

CAUTION: Make sure unit is unplugged before checking any wiring.

c) Ensure proper operation of solenoid valve. If there is an audible clicking

sound yet no water flows, look for an obstruction in the valve itself or

elsewhere in the water supply line. WARNING: Do not expose sensor to

direct sunlight.

4. Sensor Range Adjustment: The electronic sensor used in this fountain is

factory pre-set for a "visual" range of 36 inches. If actual range varies greatly

from this, or a different setting is desired, follow the range adjustment

procedure below:

a) Remove bottom cover of fountain.

b) Remove sensor by removing washers and nuts that secure sensor on studs.

c) Locate range adjustment screw between the red lenses of the sensor, then

with a small tip screwdriver, rotate the range adjusting screw clockwise to

increase range or counter-clockwise to decrease range. 1/4 turn of screw is

equal to approximately 12 - 18 inches of range.

CAUTION: Complete range of sensor (24 - 48 inches) is only one turn of the

adjusting screw.

d) Remount sensor on studs and replace bottom cover.

42, 43

NOTE: WHEN INSTALLING

REPLACEMENT BUBBLER

AND PEDESTAL, TIGHTEN

NUT (ITEM 4) ONLY TO HOLD

PARTS SNUG IN POSITION. DO

NOT OVER TIGHTEN.

FIG. 8

31 17 6

FIG. 9

ERO28C ERO28RAC

Dieses Handbuch passt für folgende Modelle

Andere Elkay Freiluftbrunnen Handbücher

Elkay

Elkay Hydroboost HTHBHAC8BLSSWF25N Installationshandbuch

Elkay

Elkay OFA25 1D Series Installationshandbuch

Elkay

Elkay Soft Sides LCRSPD10-2AQ Installationshandbuch

Elkay

Elkay Soft Sides ECDFPW314FP Gebrauchsanweisung

Elkay

Elkay EHW214FP Series Installationshandbuch

Elkay

Elkay LK4430BF1 Bedienungsanleitung

Elkay

Elkay LZO8WSS2KWN Bedienungsanleitung

Elkay

Elkay 4590 Series Bedienungsanleitung

Elkay

Elkay 4430BF1UFR Series Bedienungsanleitung

Elkay

Elkay Soft Sides ERO8C-C Installationshandbuch

Elkay

Elkay 4460YHHB Series Bedienungsanleitung

Elkay

Elkay EFRC8C-A Installationshandbuch

Elkay

Elkay EFRP12CDC_2 Installationshandbuch

Elkay

Elkay VRCTL8S2JOC Installationshandbuch

Elkay

Elkay EDFP19C series Installationshandbuch

Elkay

Elkay Endura II 4405BFEVGWR Installationshandbuch

Elkay

Elkay Soft Sides ERO8C Series Installationshandbuch

Elkay

Elkay EDFP220RC Installationshandbuch

Elkay

Elkay OFA25 2FJO Series Installationshandbuch

Elkay

Elkay ECDFPW Gebrauchsanweisung

Elkay

Elkay 4400FR Series Bedienungsanleitung

Elkay

Elkay SWIRLFLO Series Installationshandbuch

Elkay

Elkay EZWS-EDFPBM117K Gebrauchsanweisung

Elkay

Elkay HTHBHVR8-NF-25N Installationshandbuch

Beliebte Freiluftbrunnen Handbücher anderer Marken

Sunnydaze Decor

Sunnydaze Decor XSS-578 Bedienungsanleitung

Campania International

Campania International Bibendum FT-400 Bedienungsanleitung

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Bedienungsanleitung

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Bedienungsanleitung

Campania International

Campania International Juliet Fountain Bedienungsanleitung

YARDART

YARDART FT-155 Bedienungsanleitung

Alpine

Alpine WIN732 Bedienungsanleitung

Campania

Campania Valencia Bedienungsanleitung

Campania International

Campania International FT-320 Bedienungsanleitung

GardenWize

GardenWize SWGSL230 Bedienungsanleitung

Kelkay

Kelkay Easy Fountain Rustic Windmill Bedienungsanleitung

Alpine

Alpine WIN258 Bedienungsanleitung

Bond

Bond Signature Series Bedienungsanleitung

Kenroy Home

Kenroy Home 51112COPBL Installationsanleitung

EasyPro

EasyPro Tranquil Décor HBB39 Bedienungsanleitung

Angelo Decor

Angelo Decor Castillo Bedienungsanleitung

Campania International

Campania International Girona FT-102A Bedienungsanleitung

Campania International

Campania International FT-271 Bedienungsanleitung