ELTA FANS COMPACT SCD Wartungs- und Serviceanleitung

These instructions must be read fully before commencing installation.

COMPACT SCD

Installation & Maintenance

Tel 01384 275800 Fax 01384 275810 Email [email protected] Website eltafans.com2

Installation Instructions

COMPACT SCD

1.0 General

1.1 It is important these Installation and Maintenance Instructions are fully adhered to.

1.2 Full details of the unit supplied are shown on the product nameplate. If in doubt about any detail contact Elta Fans Ltd or its agents for

  clarication.

1.3  Allelectricalinstallationmustbecarriedoutbysuitablyqualiedandcompetentpersonnelinaccordancewithallcurrentstatutory 

requirements.

1.4 These instructions cover only the Elta Fans Ltd product and do not include the supply or installation of any safety equipment that may be

required e.g. adequate guarding or protection from rotating parts and proper electrical isolation.

1.5 Any declarations made by Elta Fans Ltd about product installation and safety, are dependant on the fan equipment being used within

installations which themselves meet the requirements of the relevant Standards and Directives of your region.

1.6 The fan is designed for use in an ambient temperature of -20°C up to a maximum of +50°C and up to 95% relative humidity. The fan is not

suitable for corrosive or explosive atmospheres.

1.7 The installer should provide easy access to the fan to facilitate future maintenance.

1.8 The installer should ensure the fan is adequately supported.

1.9 This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible

for their safety. Children should be supervised to ensure that they do not play with the product.

1.10 Atend-of-life,theunitmustbedisposedofinanenvironmentallyfriendlymannerbysuitablyqualiedandcompetentpersonnelin

accordance with the requirements of applicable Standards and Directives.

2.0 Installation

WARNING – The fan must be isolated from the power supply during installation and maintenance. The fan must be earthed in

accordance with the local regulations.

2.1 Upon receipt, the fan equipment should be visually inspected to check for any damage. Ensure that the impeller is free to rotate.

2.2 If there are any queries concerning the fan equipment, Elta Fans Ltd should be contacted prior to the installation.

2.3  Thefanmustbesecurelymountedinthedesiredpositiontosuittheapplication.Thefancanbemountedonatorinclinedroofswitha

maximum pitch angle of 30o .

2.4 SMF fans are supplied with the fan/motor fully assembled to the base/cowl.

DO NOT OVERTIGHTEN THE BOLTS AS THIS MAY DAMAGE THE BASE.

2.5  BackdraughtshuttersforSMFfansaresuppliedasanassembledunitandarettedpriortoroofunitinstallation.Theshutterassemblytop

  angelocatesontothecurbface.

2.6 Position the assembled roof unit onto the curb and secure to the timber sill with suitable coach bolts (not supplied by Elta Fans), ensuring

  thatbrewashersarepositionedundereachbolthead.Itisadvisabletodrillpilotholespriortottingtheboltstopreventsplittingthe 

timber curb.

DO NOT OVERTIGHTEN THE BOLTS AS THIS MAY DAMAGE THE BASE.

2.7 Check the details on the motor rating plate to ensure that the correct power supply (voltage, frequency and phase) is available. An

incorrect power supply will lead to permanent damage to the fan motor.

2.8 Remove the cowl in order to gain access to the terminal box on sizes 200 to 300.

2.9 Refer to the appropriate wiring diagram. Ensure that all earth connections are made.

2.10 Means for electrical disconnection must be incorporated in the wiring installation in accordance with the relevant wiring and electrical

regulations.

2.11 Precautionmustbetakentolocatetheexhaustdischargeterminalsoastoavoidthebackowofgasesintotheroomfromtheopenue

of gas or other fuel burning appliances.

3.0 Start Up

3.1 Before power is supplied to the unit, check that the wiring is correct as per the fan connection diagram.

3.2  Atinitialstart-up,checkthatimpellerrotationandairowdirectioniscorrect.

3.3 Check that the motor amperage draw does not exceed the nameplate rating.

Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication.

Confirmation of dimensions and data will be supplied on request. 3

Three Phase 380V - 415V / 50Hz

Page

No.

Product

Code

Wiring

Diagram No.

4SCD315/4-3AC 152- 611

4SCD350/4-3AC 152- 611

4SCD450/4-3AC 152- 611

4SCD500/4-3AC 152- 611

4SCD560/4-3AC 152- 611

4SCD630/4-3AC 152- 611

Wiring Diagrams

COMPACT SCD AC

Please use the table(s) below to match up the product code and the wiring diagram number.

Tel 01384 275800 Fax 01384 275810 Email [email protected] Website eltafans.com4

GREEN/YELLOW

EL1

FAN TERMINAL

BOX

380 - 440V 3PH 50Hz SUPPLY

FIXED SPEED CONNECTION

L3L2

GREY

BLACK

BROWN

W2 V1 V2 W1

TBTB

THERMAL CUT-OUT

CONNECT INTO

STARTER CONTROL

CIRCUIT

U1 U2 W1V2V1W2

L1/L U V WL3

L2/N 4 5 6 731 2 811109

FAN TERMINAL

BOX

BROWN

BLACK

GREY

BROWN

BLACK

GREY

GREEN/YELLOW

EL1

380 - 440V 3PH 50Hz SUPPLY

VARIABLE SPEED CONNECTION C/W 3PH - 3PH IP55/66 INVERTER

L2 L3

1 TO 7

PRE - WIRED

10 RELAY COMMON

11 RELAY CONTACT

3PH - 3PH

IP55/66 INVERTER

ANALOG / DIGITAL

INPUT CONNECTIONS

TBTB

GREEN/YELLOW

THERMAL CUT-OUT

CONNECT INTO

STARTER CONTROL

CIRCUIT

L1/L U V WL3

L2/N 4 5 6 731 2 811109

ENSURE FAN IS SUITABLE FOR THIS CONNECTION.

IF IN DOUBT CONTACT ELTA FANS

BROWN

BLUE

GREEN/YELLOW

220 - 240V 1PH 50Hz SUPPLY

VARIABLE SPEED CONNECTION C/W 1PH - 3PH IP20 INVERTER

1PH - 3PH

IP20 INVERTER

ANALOG / DIGITAL

INPUT CONNECTIONS

1: +24V OUTPUT

2: STOP/RUN DI1

3: FWD/REV DI2

4: ANALOG/PRESET DI3

5: +10V OUTPUT

6: ANALOG INPUT

7: 0V

10 RELAY COMMON

11 RELAY CONTACT

FAN TERMINAL

BOX

THERMAL CUT-OUT

CONNECT INTO

STARTER CONTROL

CIRCUIT

GREEN/YELLOW

TB TB

GREY

BLACK

BROWN

W2 V1 V2 W1U2U1

L1/L U V WL3

L2/N 4 5 6 731 2 811109

ANALOG / DIGITAL

INPUT CONNECTIONS

1PH - 3PH

IP55/66 INVERTER

10 RELAY COMMON

11 RELAY CONTACT

1 TO 7

PRE - WIRED

VARIABLE SPEED CONNECTION C/W 1PH - 3PH IP55/66 INVERTER

220 - 240V 1PH 50Hz SUPPLY

L E

GREEN/YELLOW

BLUE

BROWN

ENSURE FAN IS SUITABLE FOR THIS CONNECTION.

IF IN DOUBT CONTACT ELTA FANS

FAN TERMINAL

BOX

U1 U2 W1V2V1W2

BROWN

BLACK

GREY

TBTB

GREEN/YELLOW

THERMAL CUT-OUT

CONNECT INTO

STARTER CONTROL

CIRCUIT

L1/L U V WL3

L2/N 4 5 6 731 2 811109

ANALOG / DIGITAL

INPUT CONNECTIONS

10 RELAY COMMON

11 RELAY CONTACT

L3L2

VARIABLE SPEED CONNECTION C/W 3PH - 3PH IP20 INVERTER

380 - 440V 3PH 50Hz SUPPLY

L1 E

GREEN/YELLOW

GREY

BLACK

BROWN

1: +24V OUTPUT

2: STOP/RUN DI1

3: FWD/REV DI2

4: ANALOG/PRESET DI3

5: +10V OUTPUT

6: ANALOG INPUT

7: 0V

3PH - 3PH

IP20 INVERTER

FAN TERMINAL

BOX

THERMAL CUT-OUT

CONNECT INTO

STARTER CONTROL

CIRCUIT

GREEN/YELLOW

TB TB

GREY

BLACK

BROWN

W2 V1 V2 W1U2U1

ALL WIRING AND CONTROL EQUIPMENT MUST COMPLY TO THE

LATEST IEE REGULATIONS, IN PARTICULAR PART 552-01-02/03

21/05/2015

MK-152-611 Issue: Saved Date:C

Wiring Diagrams

152-611 AC

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03.

MK-152-611 Issue C: 21.05.2015

Check the individual product accessories table for fan controller compatibility.

Confirmation of dimensions and data will be supplied on request. 5

EC Declaration of Conformity EC Declaration of Incorporation

Description of Equipment:

Building Services Ranges - Air movement fan

Equipment model numbers for safe area fans:

SCP, SPA, SAX, SCD, SDA, SCC, SLC, SCPP, SPP, SAMF, HIT, SEM,

SEL, ISEO IMF, SH, SSD, SQS, SQSDCV, SQU, SMB, STD, SQT, SQT-

DCV, SCH, SCHT, SSDR, SSDRDCV, STDR, STDRDCV, SB, SQU-HT,

SSQU-HT, SDF, ZFHIC, SRC, CF, TF

Relevant / applied directives:

Machinery directive 2006/42/EC, Low voltage directive 2014/35/EU

Relevant / applied directives where applicable:

Energy related products directive 2009/125/EC (when used in Europe)

Electromagnetic compatibility directive 2014/30/EU (where driven via

Inverter)

Relevant / applied directives where applicable:

BS EN ISO 12100 : 2010

BS EN 14694 : 2003 + A1 : 2011

BS EN 308:1997

BS EN ISO 5801:2008

In accordance with the Machinery Directive 2006/42/EC;

The design of the partly completed machine, listed above, complies

with the Essential Health and Safety Requirements (EHSRs) of ANNEX

I, sections 1.1.2, 1.1.5, 1.4.1, 1.5.1 in EC Machinery Directive 2006/42/

EC.

Machinery is incomplete and must not be put into service until such

time as the machinery which is partly complete, is to be incorporated,

and has been assessed and Declared in Conformity with the provi-

sions of any relevant parts of the Machinery Directive.

We undertake to transmit, upon reasoned request by appropriate na-

tional authorities, relevant information relating to the partly completed

machinery identified above.

Manufacturer:

Elta Fans Limited

46 Third Avenue

Pensnett Trading Estate

Kingswinford

West Midlands

DY6 7US

United Kingdom

Date / Signature of Manufacturer: Document last revised: 28th March 2017

Name / Position of Signatory: Mr. Robert Rees Q.A.Manager Elta Fans Ltd

This is an electronic document and is valid without a signature or date. Issue Status B

Herewith we declare that the air movement equipment below, on the basis of its design and construction as partly completed

machines brought onto the market complies with relevant health and safety requirements of the EC Directives stated below. In the

event that alterations are made to the machinery without prior consent from Elta Fans Ltd, this declaration becomes invalid.

EC Declaration of

conformity/incorporation

535-IOM0018 Issue A

eltafans.com

Tel +44 (0) 1384 275800

Fax +44 (0) 1384 275810

Email [email protected].uk

46 Third Avenue, Pensnett Trading Estate, Kingswinford,

West Midlands, DY6 7US United Kingdom

Tel +44 (0) 1489 566500

Fax +44 (0) 1489 566555

Email [email protected] /export@eltafans.co.uk

17 Barnes Wallis Road, Segensworth East Industrial Estate,

Fareham, Hampshire, PO15 5ST United Kingdom

BS EN ISO 9001:2015 FM 556465

A member of

HEVAC ASSOCIATION

Applied Technology &

Building Services Export

Building Services

Inhaltsverzeichnis

Andere ELTA FANS Lüfter Handbücher

ELTA FANS

ELTA FANS Hydor HIT Series Bedienungsanleitung

ELTA FANS

ELTA FANS Revolution SLC Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS Jetflow SJ Series Bedienungsanleitung

ELTA FANS

ELTA FANS AVIO Series Bedienungsanleitung

ELTA FANS

ELTA FANS MORI dMEV II T Bedienungsanleitung

ELTA FANS

ELTA FANS QUBE SQU Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS QUIETFLOW TWIN SQT Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS Multiflow SMC Series Bedienungsanleitung

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

ELTA FANS

ELTA FANS Skyflow SSRV Series Bedienungsanleitung

ELTA FANS

ELTA FANS ZOO FAN SDF Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS HomeVent SANO IPIV Loft Bedienungsanleitung

ELTA FANS

ELTA FANS CETO 250 Handbuch

ELTA FANS

ELTA FANS VIGO400A Bedienungsanleitung

ELTA FANS

ELTA FANS Mori HR Bedienungsanleitung

ELTA FANS

ELTA FANS QUIETFLOW TWIN SQT Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS TWINFLOW STDR Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS Mori HR Series Bedienungsanleitung

ELTA FANS

ELTA FANS MORI MEV HT Bedienungsanleitung

ELTA FANS

ELTA FANS MORI dMEV II 150HT Bedienungsanleitung

ELTA FANS

ELTA FANS CETO100 Bedienungsanleitung

ELTA FANS

ELTA FANS VIGO350A Bedienungsanleitung

ELTA FANS

ELTA FANS VERSALINE VL Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS VIGO550A Service-Handbuch

Beliebte Lüfter Handbücher anderer Marken

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Lindab

Lindab LTDF Bedienungsanleitung