ELTA FANS Mori HR Series Bedienungsanleitung

Installation manual

Mori HR

PRECAUTIONS FOR INSTALLATION, USE AND MAINTENANCE

Read this manual carefully before using the product and keep it

in a safe place for reference.

This product was constructed up to standard and in compliance

with regulations relating to electrical equipment and must be

installed by technically qualified personnel.

The manufacturer assumes no responsibility for damage to

persons or property resulting from failure to observe the

regulations contained in this booklet.

•Thedeviceshouldnotbeusedforapplicationsotherthanthosespeciﬁedinthismanual.

•Afterremovingtheproductfromitspackaging,verifyitscondition.Incaseofdoubt,

contactaqualiﬁedtechnician.Donotleavepackagingwithinthereachofsmallchildren

or people with disabilities.

•Donottouchtheappliancewithwetordamphands/feet.

•Thisappliancecanbeusedbychildrenagedfrom8yearsandaboveandpersonswith

reducedphysical,sensoryormentalcapabilitiesorlackofexperienceandknowledge

if they have been given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by children without

supervision.

•Do not use the product in the presence of inammable vapours, such as alcohol,

insecticides,gasoline,etc...

•Ifanyabnormalitiesinoperationaredetected,disconnectthedevicefromthemains

supplyandcontactaqualiﬁedtechnicianimmediately.Useoriginalsparepartsonlyfor

repairs.

•Theelectricalsystemtowhichthedeviceisconnectedmustcomplywithregulations.

•Beforeconnectingtheproducttothepowersupplyorthepoweroutlet,ensurethat:

- the data plate (voltage and frequency) correspond to those of the electrical mains

 -theelectricalpowersupply/socketisadequateformaximumdevicepower. If not,

contactaqualiﬁedtechnician.

•The device should not be used as an activator for water heaters, stoves, etc., nor

shoulditdischargeintohotair/fumeventductsderivingfromanytypeofcombustion

unit.Itmustexpelairoutsideviaitsownspecialduct.

•Operatingtemperature:-20°Cupto+50°C.

•Thedeviceisdesignedtoextractcleanaironly,i.e.withoutgrease,soot,chemicalor

corrosiveagents,orammableorexplosivemixtures.

•Donotleavethedeviceexposedtoatmosphericagents(rain,sun,snow,etc.).

•Donotimmersethedeviceoritspartsinwaterorotherliquids.

•Turnoffthemainswitchwheneveramalfunctionisdetectedorwhencleaning.

•For installation an omnipolar switch should be incorporated in the ﬁxed wiring, in

accordancewiththewiringregulations,toprovideafulldisconnectionunderovervoltage

VERSIONS

STANDARD

Externalgrilleinhighquality,impactandUV-resistantABScolourRAL9010.

categoryIIIconditions(contactopeningdistanceequaltoorgreaterthan3mm).

•Ifthesupplycordisdamaged,itmustbereplacedbythemanufacturer,itsservice

agentorsimilarlyqualiﬁedpersonsinordertoavoidahazard.

•Donotobstructthefanorexhaustgrilletoensureoptimumairpassage.

•Ensureadequateairreturn/dischargeinto/fromtheroomincompliancewithexisting

regulations in order to ensure proper device operation.

•Iftheenvironmentinwhichtheproductisinstalledalsohousesafuel-operatingdevice

(waterheater,methanestoveetc.,thatisnota“sealedchamber”type),itisessential

to ensure adequate air intake, to ensure good combustion and proper equipment

operation.

INTRODUCTION

MORI HR is a continuously running, alternate flow supply and extract fan with heat

retention for use in habitable rooms such as; living rooms, bedrooms, dining rooms

basements and hallways. It is designed to ensure adequate ventilation in enclosed

environments.Itisrecommendedthattwounitsareinstalledinapair:whenoneunitis

pulling,theotherispushing.

Apairofunitscanbeinstalledinthesameroomorindifferentrooms(i.e.livingroom

and bedroom). The unit is suitable for installation on an outside wall.

To achieve the best possible ventilation the unit should operate

continuously, and only stopped for maintenance or service.

When heat exchange is not useful (for example in mid-seasons when

indoor and outdoor temperatures are similar) it is recommended to set the

unit in “extract-only” or “intake-only” mode and not switch the fan off.

•Innerventilationunitmaterial:highquality,impactandUV-resistantABScolourRAL9010.

•Designfrontcoverremovableforcleaningwithouttheuseoftools.

•Easymaintenanceinstallationplate,foreasyaccesstotheheatexchangerfrominside

the room.

•Anti-dustﬁlter,easilyremovableforwashingbytheuserwithouttools.

•Regenerativehoneycombsceramicheatexchanger.

•Externalgrilleinhighquality,impactandUV-resistantABScolourRAL9010.

•High efﬁciency aerodynamic fan with “winglet” blades to optimise quietness and

efﬁciency.

•SinglephaseECreversibleBrushlessmotorwithintegralthermalprotection.

•Motormountedonhighqualityballbearings.

•Theunitisdoubleinsulated:noearthconnectionisrequired.

•Tricklespeedselectable.

•Boostmode.

•Free-cooling(Bypass)mode.

•IPX4degreeofprotection.

•Powersupply220Vto240V~50Hz.

TECHNICAL SPECIFICATIONS

Model Airﬂow

l/s

Power

Weight

MoriHR100 2,8/4,2/7 1,2/1,7/2,6 2

MoriHR150 5,6/11,1/16,7 1,4/2,3/3,8 4,2

Every70secondstheunitalternatesbetweenbeingasupplyfanandanextractfan.

Duringtheextractmodetheunitshighefﬁciencyheatexchangercollectsandretains

heatfromtheextractedair,itthentransfersthemajorityofthisheattotheincomingair

duringsupplymode,recoveringmostofthermalenergywhichwouldbeotherwiselost

in the ventilation process.

Theunitcanberuncontinuouslyatasetspeedbyaddinganinternallink,orcontrolled

viathededicatedcontroller,149-SEN-CTRLSwhichallowsspeedselectionandtriggering

of free cooling mode.

S3switchactivatesthe“Freecooling“(Bypass)mode,whichstopsalternateowand

keepsthefanin“extract-only”or“intake-only”mode,toavoidtheheatexchangewhen

necessary.Tosettheextract-only”modeor“intake-only”,placetheintegraljumpersas

perFig.20AorFig.20B).ThefrontcoverLEDindicateswhentheFreecoolingmodeison.

Anautomatic“Boost”modecanbeachievedthroughadedicatedswitchorroomsensors

like149-SEN-HY,149-SEN-PIRor149-SEN-CO2.

Wiringconﬁgurations:

1.ConstantrunwithalternateowandheatretentiononSpeed1only(Fig.18A).

2.ConstantrunwithalternateowandheatretentiononSpeed2only(Fig.18B).

3.ConstantrunwithalternateowandheatretentiononSpeed3only(Fig.18C).

4.ConstantrunwithalternateowandheatretentiononSpeed1withboosttoSpeed3

triggeredbyexternalswitchingdevice(orderedseparatelyifrequired)(Fig.18D).

5.ConstantrunwithalternateowandheatretentiononSpeed2withboosttoSpeed3

triggeredbyexternalswitchingdevice(orderedseparatelyifrequired)(Fig.18E).

6.Operationusingcontroller149-SEN-CTRLS(orderedseparatelyifrequired)(Fig.18F).

(a)Off.

(b)ConstantrunwithalternateowandheatretentiononSpeed1.

(c)ConstantrunwithalternateowandheatretentiononSpeed2.

(c)ConstantrunwithalternateowandheatretentiononSpeed3.

(d)Constantrunon selectedspeedinextractorsupplymodeonly(supplyorextract

selectable at installation stage).

Pleasenotethatthisswitchcancontroloneortwounitstoworkinharmonyi.e.when

oneunitisextractingtheotherissupplyingwhichcanimprovefurthertheventilationin

aroomorhome.Wiringdiagramfor2units,Fig.18G.

“S1” “S2” Operation

O O OFF

I O Speed1

O II Speed2

I II Speed3

S1 S2 S3

“S3” Operation

Heatrecovery

(Alternateow)

Freecooling

OPERATION

WARNING: Ensure that the electric wiring to L and N is done correctly; an

incorrect connection will lead to malfunction or permanent damage of the fan.

Twoormoreunitscanoperateataﬁxedspeedinasynchronisedway(oneunitextracts,

theothersupplies,andviceversa).Wiringdiagrams:Fig.18A-18B-18C.

Theinitialstartingairdirectionisachievedbysettingthededicatedjumper(Fig.20A-20B).

RESET OF THE SYNCHRONISATION

OPTION 1:Iftwoormoreunitsareconnectedunderthesamemainswitchorundera

dedicatedswitch,toresetthesynchronisation,theswitchmustbeswitchedﬁrstOFFand

thenONtoreactivate(Fig.31).

SYNCHRONISATION IN CASE OF INSTALLATION WITHOUT CONTROLLER

Maintenance can be carried out by the user as indicated at page 11.

Servicemustbeperfmormedonlybytechnicallyqualiﬁedpersonnelinaccordancewith

local rules and regulations. Make sure that the mains supply to the unit is disconnected

(page12).Cleaningoftheheatexchangercanbeperformedfromoutsideaswell.

MAINTENANCE AND SERVICE

IntegraljumpersetinpositionA(Fig.20A)means“extract”mode.

IntergaljumpersetinpositionB(Fig.20B)means“intake”mode.

Thejumperpositiondeﬁnesboththeair-owdirectionwhentheunitisactivatedforthe

ﬁrsttime(forthesynchronisation)andtheair-owdirectionofthefree-coolingmode.

JUMPER POSITION

Iftwoormoreunitsarecontrolledbymeansofthesamecontroller(149-SEN-CTRLSor

similar),theyalwaysoperateinasynchronisedway.WiringdiagramasperFig.18.

SYNCHRONISATION IN CASE OF INSTALLATION WITH CONTROLLER

DIMENSIONS

270÷510

164

108

A

270÷510

164

108

270÷510

164

108

C

ØE

Externalgrille

270÷510

164

108

MoriHR100 MoriHR150

A164 218

B 46 51

C164 218

D 270÷510 300÷560

Ø E 108 158

OPTION 2:Iftwoormoreunitsarenotconnectedunderthesamemainswitch,toreset

thesynchronisation,pressatthesametimetheblackpinofeachunit(Fig.32-33)at

least3seconds.

Year1 Inspectionofﬁltercleanliness,ifrequiredwashunderatap(page11)

Year2 Inspectionofﬁltercleanliness,ifrequiredwashunderatap(page11)

Inspectionofheatexchangercore,ifrequiredwashunderatap(page12)

Year3 Inspectionofﬁltercleanliness,ifrequiredwashunderatap(page11)

Year4 Inspectionofﬁltercleanliness,ifrequiredwashunderatap(page11)

Inspectionofheatexchangercore,ifrequiredwashunderatap(page12)

Year5 Inspectionofﬁltercleanliness,ifrequiredwashunderatap(page11)

INSTALLATION

CONTENUTO IMBALLO MODELLO MORI HR

MoriHR100-MoriHR150

min. 108mm HR100

min. 158mm HR150 INDOOR OUTDOOR

1°÷2°

insulation foam

=Ø 5x40mm

=Ø 8x10mm

8 9

10 11

100mm HR100

115mm HR150

12 13

14 15

16 17

18C

S3 S2 S1 GND

N L

S3 S2 S1 GND N L

SPEED 1 (FIXED) SPEED 2 (FIXED)

SPEED 3 (FIXED)

S3 S2 S1 GND N L

CTRL-S

S1 S2 S3

1 1 1

S3 S2 S1

18F

18A 18B

S3 S2 S1 GND

N L

S3 S2 S1 GND N L

SPEED 1 to 3

SPEED 2 to 3

18D

18E

S3 S2 S1 GND N L

S1 S2 S3

S3 S2 S1 GND N L

CTRL-S

1 1 1

S3 S2 S1

18G

UNIT 1 UNIT 2

S3 S2 S1 GND N L

CTRL-S

S1 S2 S3

1 1 1

S3 S2 S1

18F

AGGIUNTA FOGLIO ISTRUZIONI -

JUMPER POSITION A

20A

EXTRACT

AGGIUNTA FOGLIO ISTRUZIONI -

JUMPER POSITION B

20B

INTAKE

23 CLICK 24

Ø 5x40mm

3-5mm

EXTERNAL GRILLE

TO RESET OF THE SYNCHRONIZATION OF THE UNITS (OPTION 2)

TO RESET OF THE SYNCHRONIZATION OF THE UNITS (OPTION 1)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ELTA FANS Lüfter Handbücher

ELTA FANS

ELTA FANS MORI MEV HT Bedienungsanleitung

ELTA FANS

ELTA FANS Revolution SLC Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS Hydor HIT Series Bedienungsanleitung

ELTA FANS

ELTA FANS VIGO400A Bedienungsanleitung

ELTA FANS

ELTA FANS TWINFLOW STDR Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS QUIETFLOW TWIN SQT Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS Mori HR Bedienungsanleitung

ELTA FANS

ELTA FANS AVIO Series Bedienungsanleitung

ELTA FANS

ELTA FANS Jetflow SJ Series Bedienungsanleitung

ELTA FANS

ELTA FANS QUBE SQU Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS HomeVent SANO IPIV Loft Bedienungsanleitung

ELTA FANS

ELTA FANS VERSALINE VL Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS VIGO550A Service-Handbuch

ELTA FANS

ELTA FANS VIGO350A Bedienungsanleitung

ELTA FANS

ELTA FANS Multiflow SMC Series Bedienungsanleitung

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

ELTA FANS

ELTA FANS COMPACT SCD Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS QUIETFLOW TWIN SQT Series Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS MORI dMEV II T Bedienungsanleitung

ELTA FANS

ELTA FANS ZOO FAN SDF Wartungs- und Serviceanleitung

ELTA FANS

ELTA FANS MORI dMEV II 150HT Bedienungsanleitung

ELTA FANS

ELTA FANS Skyflow SSRV Series Bedienungsanleitung

ELTA FANS

ELTA FANS CETO100 Bedienungsanleitung

ELTA FANS

ELTA FANS CETO 250 Handbuch

Beliebte Lüfter Handbücher anderer Marken

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Lindab

Lindab LTDF Bedienungsanleitung