Emerson ER107001 Bedienungsanleitung

Wireless 720P HD Video Doorbell

and Indoor Chime with Two-Way Audio,

Motion-Activated Alerts and Night

Vision for IOS and Android App

OWNER’S MANUAL

ER107001

Visit our web site at www.emersonradio.com

UNAUTHORIZED MODIFICATIONS TO THIS DEVICE

COULD VOID MANUFACTURER’S WARRANTY

Download and Install the app from the App Store or

Google Play Store.

-1-

2. Device Overview

Infrared LED

Camera Image Sensor

Microphone

Speaker

Call Button

Reset Button

Power OFF/ON Switch

Micro SD Card Slot

WiFi Signal Indicator

PIR Motion Sensor

Battery Charging Indicator

Photodiode

1.Package Contents

USB Charging Slot

Doorbell Mounting

Plate

Chime USB

Cable

Owner’s

Manual

Screw

Driver

6 Long Screws,

1 Short Screw

and 6 Anchors

-2-

During setup process, the Doorbell and your phone should be

connected to the same 2.4 GHz Wi-Fi platform. In order to

answer your visitor's incoming call at any time, please allow this

App to run in background.

Please refer to the chart below for the information

about the indicator lights:

3. Getting Started with the App

Description

The device is connected to the network

Steady Blue

Off

Steady Red

Steady Blue

Off

Indicator Light

Wifi Signal

Indicator

Battery

Charging

Indicator Battery is not connected to USB cable

for charging

1.Open the App Store (for iPhone) or Google Play Store (for

Android device).

2.Search "Emerson Doorbell" App and install.

3.Choose your country .

4.The settings of different phones may be different. You may

be asked to allow different kinds of permissions during

installation of the App or during video doorbell setup. Please

allow all the permissions to ensure the device works as

intended.

5.Allow App to run in background.

6.You may be asked to allow float window permissions. Please

tap "set" and allow the app to draw over other apps.

Compatible with IOS 9.0 or above (for iPhone) or

TM TM

Android 4.2 or above (for Android device).

Please refer to the operating system requirements

as specified on the App Store or Google Play Store.

Note:

Charging Connector Base

(AC 8V 24V)

If a power supply system (AC 8V~24V) for doorbells

is available with your house, you can connect it to

the Charging Connector Base terminals as shown in

section 10.

The device is not connected to the

network or in Standby mode

Battery is charging

Battery charging is completed

Note:

Wireless 720P HD Video Doorbell

and Indoor Chime with Two-Way Audio,

Motion-Activated Alerts and Night

Vision for IOS and Android App

OWNER’S MANUAL

ER107001

Visit our web site at www.emersonradio.com

UNAUTHORIZED MODIFICATIONS TO THIS DEVICE

COULD VOID MANUFACTURER’S WARRANTY

-3- - 4 -

This section is for iPhone only. For Android device,

please refer to section 5.

1. Fully charge the doorbell by plugging it into a power source

with the USB cable provided. The indicator light will become

steady blue once fully charged (Please refer to Section 2).

2. Power On, then open the App and tap "+"

4 .Follow the in-app instructions . Press and hold the Call

Button for 5 seconds and the doorbell light will start blinking.

OFF ON

4. Video Doorbell Setup for iPhone

3.Tap "Search Network"  Tap "Connect to Wifi"

5. In your phone's Settings, select and connect to the Wifi named

"Wifi_Doorbell_AP". Please wait as it may take some time to

detect and show this Wifi.

7. Tap "Next" and select your desired Wifi network

(2.4 GHz Wifi only).

8.Enter Wifi password and tap "OK" to proceed.

6. Please wait until the connection to "Wifi_Doorbell_AP" is

successful. Then go back to Emerson Doorbell App to continue.

9. Enter the password of device and tap OK

(default password is admin ).

" "

10. Please go to Section 7 to update the settings and change

your password.

Note: This device works with multiple users. Once this

device has been added by the first user, there are

several options for the subsequent users to add the

device (Please refer to Section 6).

-5- - 6 -

Successfully added the device

5. Video Doorbell Setup for Android Device

This section is for Android device only. For iPhone, please

refer to section 4.

1. Fully charge the doorbell by plugging it into a power source

with the USB cable provided. The indicator light will become

steady blue once fully charged (Please refer to Section 2).

5. Follow the in-app instructions . Press and hold the Call Button

for 5 seconds and the doorbell light will flash. Tap "Next".

6. Enter Wifi password and tap "Next" to proceed. To use different

Wifi network, tap as indicated to search (2.4GHz Wifi only).

OFF ON

2. Power On, then open the App and tap "+"

3. Your phone should be connected to the 2.4 GHz Wifi during

setup.

4. Tap "Search Network"  Tap "Connect to Wifi"

-7- - 8 -

-9-

8. Please refer to Section 7 to update the settings and change

your password.

This device works with multiple users. Once this

device has been added to the first user, there are

several options for the subsequent users to add the

device (Please refer to Section 6).

Note:

7. Please wait until there is pop-up for the password of device.

Enter the password and tap "OK"

(default password is: admin).

Successfully added the device

6. Add Video Doorbell for Multi-Users

This device works with multiple users. Once this device

has been connected to the network, there are more options

for the subsequent users to add the device to their App.

1. Refer to Section 3 to download and install the App.

2. Make sure your phone is connected to the same 2.4 GHz Wifi

network that you will be connecting your device to.

3.Power On, then open the App and tap "+"

OFF ON

4.Option 1:

a. Press the Call Button once and the Wifi signal indicator

wil l become steady blue.

WiFi Signal Indicator

b. Tap "Search Network" Tap "LAN Search (for Multiple Users)

-10-

c. Select the device and enter password. Then tap "OK".

Note: Default password is "admin" but it may be changed by the

first user. Please check and confirm the password first.

Option 2:

Tap "Scan QR Code" and scan the QR code label

on back of the doorbell. Enter password and tap "OK".

Note: Default password is admin but it may be changed by

the first user. Please check and confirm the password

first.

" "

Note: Default password is "admin" but it may be changed

by the first user. Please check and confirm the

password first.

Option 3:

Tap "Input Manually". Rename the device, enter DID

(case sensitive) and password. Then tap "OK".

DID (uppercase and

lowercase letters

should match)

7. App Settings

1. Press the Call Button and enter intercom state . Tap

"Settings" icon.

Slide to right

-11 - - 12-

Successfully added

the device

Successfully added the device

Successfully added

the device

a. Device name (Refer to point 2 to rename)

b. Device ID (For information only, cannot be changed)

c. Modify password (any characters or numbers and 4-16 in

length) Noted: please alert other users after change of

password

d. Upgrade firmware(Tap to upgrade)

e. Micro SD Card Record (Pictures by motion detection will be

saved here. There is no option if micro SD card is not

inserted in the device)

f. Loop Record if the Micro SD Card is Full.

g. PIR Sensor

h. Push-PIR

I. Wifi Setting (Tap for change)

Note:

2.Tap the below icons shown on device list.

Device List

2.1

2.2 Push Notifications Enable/ Disable push notifications

If PIR sensor is OFF, no push notification even

though Push-PIR is ON. If PIR sensor is ON while

Push-PIR is OFF, only picture will be saved in the

Micro SD card and no push notification.

2.1

2.2

2.3

Rename the device

Device ID(cannot be changed)

If the password is incorrect, you may

not receive calls and notifications.

Please enter correct password here

and tap “Save"

Tap here to remove device from

the list

-13 - - 14-

120m

Doorbell

Chime

1.LED Indicator

2.Volume Button

3.Ringtone Button

4.Pairing Button

5.Battery Box

8. Settings for Chime

Chime is an optional add-on that alerts you when your

doorbell rings even if your phone is off or not in use.

1. Press (3) to select ringtone

2. Press (2) to set volume

3. Chime is already paired with the doorbell. The following

procedures applies to new chime or additional chime only.

a. Press the paring button (4) under standby mode.

b. Press the call button of doorbell.

c. The LED indicator (1) blinks then OFF if pairing is successful.

2.3

9. Answering Calls and Playback

Enable/Disable Ringtone on phone

App Version

Select Ringtone

Enable/Disable Vibration Notice on

Phone (only for AndroidTM Device)

When a visitor presses the Call Button, press the notification

banners (ring notifications must be Enabled) or tap on the

answer icon if in blue.

-15 - - 16-

Slide to left to

hang up

Slide to right to

enter intercom

interface to answer

Tap to take photo Tap to take video,

tap again to stop

Exit

Battery Indication

Turn On/Off the

image

Noted: Switch off this

function can improve

audio quality.

10. Hardwiring and Installation

USB Charging Slot

Charging Connector Base

Reset Button

OFF ON

Micro SD card slot

Power OFF/ON

(AC 8V 24V)

Intercom Interface:

-17 - - 18-

Photos saved in

smartphone.

Videos saved in

smartphone.

Photos by motion detection

saved in Micro SD card.

Hang up Slide to right and

hold to talk to

visitor

Tap to take video.

Tap again to stop.

Tap to take photo.

Green if micro SD

card has been

inserted.

ON: Talk and hear at the same time (Max. 120 seconds)

OFF: Slide the below icon to the right and hold to talk. Then

release the icon to hear.

Playback:

You may take snapshots and videos when there is incoming call

or during intercom. Snapshots and videos are stored in your

smartphone. Tap the “Snapshots Playback” icon and “Videos

Playback” icon in the main manual to enter the playback

interface.

Event History:

When PIR is enabled and Micro SD card has been inserted to

the device, snapshots will be saved in Micro SD card whenever

motion is detected. Tap the below icon to view the snapshots.

Inhaltsverzeichnis

Andere Emerson Zubehör Handbücher

Emerson

Emerson Rosemount 389 Bedienungsanleitung

Emerson

Emerson Carbon Dioxide Sensor Betriebsanleitung

Emerson

Emerson Rosemount 499ACL-01 Bedienungsanleitung

Emerson

Emerson ER40 Bedienungsanleitung

Emerson

Emerson Rosemount 3200HP Bedienungsanleitung

Emerson

Emerson Micro Motion Elite Coriolis CMF400 Bedienungsanleitung

Emerson

Emerson Rosemount 0065 Bedienungsanleitung

Emerson

Emerson AVENTICS ST4-2P Bedienungsanleitung

Emerson

Emerson Rosemount 222 Bedienungsanleitung

Emerson

Emerson Rosemount 385 Bedienungsanleitung

Emerson

Emerson MICROMOTION CNG050 Bedienungsanleitung

Emerson

Emerson Rosemount TupHFET TF396 Bedienungsanleitung

Emerson

Emerson AVENTICS SM6-AL Bedienungsanleitung

Emerson

Emerson Micro Motion ELITE CMF200A Bedienungsanleitung

Emerson

Emerson EASYHEAT MSA-1 Montageanleitung

Emerson

Emerson Wall-Mounted RH Sensor and RH Betriebsanleitung

Emerson

Emerson Rosemount 214C Bedienungsanleitung

Emerson

Emerson 210-2000 Bedienungsanleitung

Emerson

Emerson Rosemount 3500P Bedienungsanleitung

Emerson

Emerson AVENTICS ST6 Bedienungsanleitung

Emerson

Emerson Micro Motion H Series Bedienungsanleitung

Emerson

Emerson Micro Motion F Series Bedienungsanleitung

Emerson

Emerson 03100-0001-0001 Bedienungsanleitung

Emerson

Emerson Rosemountl Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung