Emerson Rosemount 214C Bedienungsanleitung

Quick Start Guide

00825-0400-2654, Rev AF

August 2017

Rosemount™214C Sensor

August 2017

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 214C Sensor models.

If the sensor was ordered assembled to a temperature thermowell or transmitter, see the appropriate product

literature for information on configuration and hazardous locations certifications.

Explosions could result in death or serious injury.

Installation of this sensor in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread form. Entries

marked “M20” are M20 ⫻1.5 thread form. On devices with multiple conduit entries, all conduit entries will

have the same thread form.

When installing in a hazardous location, use only appropriately listed or Ex certified flameproof/dust plugs,

adapters, or glands in cable/conduit entries.

Only use plugs, adapters, glands, or conduit with a compatible thread form when closing these entries.

Contents

Wiring diagram for RTDs . . . . . . . . . . . . . . . . 3

Wiring diagram for thermocouples . . . . . . 4

Product certifications . . . . . . . . . . . . . . . . . . . 5

Installation drawings . . . . . . . . . . . . . . . . . . .10

Quick Start Guide

August 2017

1.0 Wiring diagram for RTDs

Figure 1. RTD Lead Wire Configuration per IEC 60751

Note

To configure a single element, 4-wire RTD as a 3-wire system, connect only one white lead.

Insulate or terminate the unused white lead in a manner that prevents shorting to the ground.

To configure a single element, 4-wire RTD as a 2-wire system, connect matching colored wires

first and then connect the paired wires to the terminal.

Single element, 3-wire Single element, 4-wire Dual element, 3-wire

Red

White

Red

White

Red

White

Black

Yellow

August 2017

Quick Start Guide

2.0 Wiring diagram for thermocouples

Figure 2. Thermocouple Lead Wire Configuration

Note

Dual thermocouple sensors are shipped with one pair of the wires shrink wrapped together.

Single thermocouple, 2-wire Dual thermocouple, 4-wire

IEC 60584 thermocouple colors ASTM E- 230 thermocouple colors

Type POS (+) NEG (-) POS (+) NEG (-)

JBlack White White Red

KGreen White Yellow Red

TBrown White Blue Red

( – )

( + ) ( + )

(

)

( – )

Quick Start Guide

August 2017

3.0 Product certifications

Rev 1.12

3.1 European Directive information

A copy of the EU Declaration of Conformity can be found at the end of the Quick Start Guide.

The most recent revision of the EU Declaration of Conformity can be found at

Emerson.com/Rosemount.

3.2 Ordinary Location Certification

The Rosemount 214C has been examined and tested to determine that the design meets the

basic electrical, mechanical, and fire protection requirements by a nationally recognized test

laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration

(OSHA).

3.3 North America

The US National Electrical Code®(NEC) and the Canadian Electrical Code (CEC) permit the use

of Division marked equipment in Zones and Zone marked equipment in Divisions. The

markings must be suitable for the area classification, gas, and temperature class. This

information is clearly defined in the respective codes.

E5 Explosionproof (XP) and Dust-Ignitionproof (DIP)

Certificate: 70044744

Standards: FM 3600:2011, FM 3615:2006, UL 50E:2007, UL 61010-1:2010, ANSI/ISA

60529:2004

Markings: XP CL I, DIV 1, GP B, C, D; DIP CL II, DIV 1, GP E, F, G; CL III; T6 (–50 °C ≤Ta≤

+80 °C), T5 (–50 °C ≤Ta≤ +95 °C); Seal not required; installed per Rosemount

drawing 00214-1030; Type 4X†; Vmax 35 VDC, 750 mWmax

Special Conditions for Safe Use (X):

1. Flameproof joints are not intended for repair.

2. Cable entries must be used which maintain the ingress protection of the enclosure. Unused

cable entries must be filled with suitable blanking plugs.

N5 Division 2 (NI)

Certificate: 70044744

Standards: FM 3600:2011, FM 3611:2004, UL 50E:2007, UL 61010-1:2010, ANSI/ISA

60529:2004

Markings: NI CL I, DIV 2, GP A, B, C, D; T6 (–50 °C ≤Ta≤+80 °C),

T5 (–50 °C ≤Ta≤ +95 °C); installed per Rosemount drawing 00214-1030; Type

4X†; Vmax 35 VDC, 750 mWmax

E6 Explosionproof and Dust-Ignitionproof

Certificate: 70044744

Standards: CAN/CSA C22.2 No. 0:2010, CAN/CSA No. 25-1966,

CAN/CSA C22.2 No. 30-M1986, CAN/CSA C22.2 No. 94-M1991,

CAN/CSA C22.2 No. 61010-1:2012

Markings: Explosionproof CL I, DIV 1, GP B, C, D; Dust-Ignitionproof CL II, DIV 1,

GP E, F, G; CL III; T6 (–50 °C ≤Ta≤+80 °C), T5 (–50 °C ≤Ta≤+95 °C);

Seal not required; installed per Rosemount drawing 00214-1030; Type 4X†;

Vmax 3 5VDC, 750 mWmax

August 2017

Quick Start Guide

Special Conditions for Safe Use (X):

1. Flameproof joints are not intended for repair.

2. Cable entries must be used which maintain the ingress protection of the enclosure. Unused

cable entries must be filled with suitable blanking plugs.

N6 Division 2

Certificate: 70044744

Standards: CAN/CSA C22.2 No. 0:2010, CAN/CSA C22.2 No. 94-M1991, CAN/CSA No.

213-M1987, CAN/CSA C22.2 No. 61010-1:2012

Markings: CL I, DIV 2, GP A, B, C, D; T6; (–50 °C ≤Ta≤+80 °C), T5 (–50 °C ≤Ta≤+95 °C);

installed per Rosemount drawing 00214-1030; Type 4X†; Vmax 35 VDC,

750 mWmax

†Spring loaded indicator has reduced ingress and dust ratings. Spring loaded sensors must be

installed in a thermowell to maintain dust and ingress ratings. Un-painted aluminum

enclosures are Type 4 rated.

3.4 Europe

E1 Flameproof

Certificate: DEMKO 16 ATEX 1677X

Standards: EN 60079-0:2012+A11 2013, EN 60079-1:2014

Markings: II 2 G Ex db IIC T6…T1 Gb

Vmax = 45 Vdc, Pmax = 750 mW

Installation Instructions:

1. Use field wiring suitable for both the minimum and maximum service temperatures.

2. These devices are provided without cable glands/conduit sealing devices/blanking

elements. Proper selection of suitable cable glands/conduit sealing/blanking elements

should occur in the field.

3. Unused apertures shall be closed with suitable blanking elements.

4. The enclosures may be provided with up to three 1/2–14 NPT, 3/4–14 NPT, or M20 x 1.5

entries, with location of the entries specified in the installation instructions document.

Special Conditions for Safe Use (X):

1. Refer to certificate for details regarding process and ambient temperature limits.

2. When the Rosemount 214C sensor is provided with an enclosure with a display cover, the

maximum ambient shall be 95 °C.

3. The non-metallic label on the device may store an electrostatic charge and become a

source of ignition in Group III atmospheres. Care shall be taken to reduce electrostatic

build-up. For example, the non-metallic label may be rubbed with a damp cloth.

4. The display covers were impacted at 4 J according to a low risk of mechanical danger. Guard

the display covers against impact energies greater than 4 J.

5. Flameproof joints are not intended for repair.

6. The stand-alone Rosemount 214C sensors without an enclosure must be assembled to a

suitable Ex certified enclosure of a volume no greater than 0.55 L to maintain the types of

protection “db” and “tb”.

7. The spring loaded sensors and DIN sensors must be installed in a thermowell to maintain

IP6X ratings.

8. Contact indicating sensors do not meet requirements for protection type “tb” and

therefore are not “tb” rated.

Quick Start Guide

August 2017

I1 ATEX Intrinsic Safety

Certificate: Baseefa16ATEX0101X

Standards: EN 60079-0:2012+A11:2013, EN 60079-11:2012

Markings: II 1 G Ex ia IIC T5/T6 Ga (SEE CERTIFICATE FOR SCHEDULE)

Special Condition of Use (X):

1. The equipment must be installed in an enclosure which affords it a degree of ingress

protection of at least IP20.

N1 ATEX Type n – with enclosure

Certificate: BAS00ATEX3145

Standards: EN 60079-0:2012+A11:2013, EN 60079-15:2010

Markings: II 3 G Ex nA IIC T5 Gc T5(-40 °C≤ Ta≤ 70 °C)

ND Dust

Certificate: DEMKO 16 ATEX 1677X

Standards: EN 60079-0:2012+A11 2013, EN 60079-31:2014

Markings: II 2 D Ex tb IIIC T 130 °C Db

Vmax = 45 Vdc, Pmax = 750 mW

Installation Instructions:

1. Use field wiring suitable for both the minimum and maximum service temperatures.

2. These devices are provided without cable glands/conduit sealing devices/blanking

elements. Proper selection of suitable cable glands/conduit sealing/blanking elements

should occur in the field.

3. Unused apertures shall be closed with suitable blanking elements.

4. The enclosures may be provided with up to (3) 1/2–14 NPT, 3/4–14 NPT, or M20 ⫻1.5

entries, with location of the entries specified in the installation instructions document.

Special Conditions for Safe Use (X):

1. Refer to certificate for details regarding process and ambient temperature limits.

2. When the Rosemount 214C sensor is provided with an enclosure with a display cover, the

maximum ambient shall be 95 °C.

3. The non-metallic label on the device may store an electrostatic charge and become a

source of ignition in Group III atmospheres. Care shall be taken to reduce electrostatic

build-up. For example, the non-metallic label may be rubbed with a damp cloth.

4. The display covers were impacted at 4 J according to a low risk of mechanical danger. Guard

the display covers against impact energies greater than 4J.

5. Flameproof joints are not intended for repair.

6. The stand-alone Rosemount 214C sensors without an enclosure must be assembled to a

suitable Ex certified enclosure of a volume no greater than 0.55 L to maintain the types of

protection “db” and “tb”.

7. The spring loaded sensors and DIN sensors must be installed in a thermowell to maintain

IP6X ratings.

8. Contact indicating sensors do not meet requirements for protection type “tb” and

therefore are not “tb” rated.

Thermocouples; Pi = 500 mW T6 60 °C ≤Ta≤+70 °C

RTDs; Pi = 192 mW T6 60 °C ≤Ta≤+70 °C

RTDs; Pi = 290 mW T6 60 °C ≤Ta≤+60 °C

T5 60 °C ≤Ta≤+70 °C

August 2017

Quick Start Guide

3.5 International

E7 Flameproof

Certificate: IECEx UL 16.0048X

Standards: IEC 60079-0:2011, IEC 60079-1:2014

Markings: Ex db IIC T6…T1 Gb

Vmax = 45 Vdc, Pmax = 750 mW

Installation Instructions:

1. Use field wiring suitable for both the minimum and maximum service temperatures.

2. These devices are provided without cable glands/conduit sealing devices/blanking

elements. Proper selection of suitable cable glands/conduit sealing/blanking elements

should occur in the field.

3. Unused apertures shall be closed with suitable blanking elements.

4. The enclosures may be provided with up to three 1/2–14 NPT, 3/4–14 NPT, or M20 ⫻1.5

entries, with location of the entries specified in the installation instructions document.

Special Conditions for Safe Use (X):

1. Refer to certificate for details regarding process and ambient temperature limits.

2. When the Rosemount 214C sensor is provided with an enclosure with a display cover, the

maximum ambient shall be 95 °C.

3. The non-metallic label on the device may store an electrostatic charge and become a

source of ignition in Group III atmospheres. Care shall be taken to reduce electrostatic

build-up. For example, the non-metallic label may be rubbed with a damp cloth.

4. The display covers were impacted at 4 J according to a low risk of mechanical danger. Guard

the display covers against impact energies greater than 4J.

5. Flameproof joints are not intended for repair.

6. The stand-alone Rosemount 214C sensors without an enclosure must be assembled to a

suitable Ex certified enclosure of a volume no greater than 0.55 L to maintain the types of

protection “db” and “tb”.

7. The spring loaded sensors and DIN sensors must be installed in a thermowell to maintain

IP6X ratings.

8. Contact indicating sensors do not meet requirements for protection type “tb” and

therefore are not “tb” rated.

I7 IECEx Intrinsic Safety

Certificate: IECEx BAS 16.0077X

Standards: EN 60079-0:2012+A11:2013, EN 60079-11:2012

Markings: Ex ia IIC T5/T6 Ga (SEE CERTIFICATE FOR SCHEDULE)

Special Condition of Use (X):

1. The equipment must be installed in an enclosure which affords it a degree of ingress

protection of at least IP20.

N7 IECEx Type n – with enclosure

Certificate: IECEx BAS 07.0055

Standards: IEC 60079-0:2011, IEC 60079-15:2010

Markings: Ex nA IIC T5 Gc; T5(–40 °C ≤ Ta≤ +70 °C)

Thermocouples; Pi = 500 mW T6 60 °C ≤Ta≤+70 °C

RTDs; Pi = 192 mW T6 60 °C ≤Ta≤+70 °C

RTDs; Pi = 290 mW T6 60 °C ≤Ta≤+60 °C

T5 60 °C ≤Ta≤+70 °C

Quick Start Guide

August 2017

NK Dust

Certificate: IECEx UL 16.0048X

Standards: IEC 60079-0:2011, IEC 60079-31:2013

Markings: Ex tb IIIC T 130 °C Db

Vmax = 45 Vdc, Pmax = 750 mW

Installation Instructions:

1. Use field wiring suitable for both the minimum and maximum service temperatures.

2. These devices are provided without cable glands/conduit sealing devices/blanking

elements. Proper selection of suitable cable glands/conduit sealing/blanking elements

should occur in the field.

3. Unused apertures shall be closed with suitable blanking elements.

4. The enclosures may be provided with up to three 1/2–14 NPT, 3/4–14 NPT, or M20 ⫻1.5

entries, with location of the entries specified in the installation instructions document.

Special Conditions for Safe Use (X):

1. Refer to certificate for details regarding process and ambient temperature limits.

2. When the Rosemount 214C sensor is provided with an enclosure with a display cover, the

maximum ambient shall be 95 °C.

3. The non-metallic label on the device may store an electrostatic charge and become a

source of ignition in Group III atmospheres. Care shall be taken to reduce electrostatic

build-up. For example, the non-metallic label may be rubbed with a damp cloth.

4. The display covers were impacted at 4 J according to a low risk of mechanical danger. Guard

the display covers against impact energies greater than 4J.

5. Flameproof joints are not intended for repair.

6. The stand-alone Rosemount 214C sensors without an enclosure must be assembled to a

suitable Ex certified enclosure of a volume no greater than 0.55 L to maintain the types of

protection “db” and “tb”.

7. The spring loaded sensors and DIN sensors must be installed in a thermowell to maintain

IP6X ratings.

8. Contact indicating sensors do not meet requirements for protection type “tb” and

therefore are not “tb” rated.

3.6 Combinations

KA Combination of E1 and E6

KB Combination of E5 and E6

KC Combination of E1 and E5

KD Combination of E1, E5, and E6

KN Combination of N1, N5, N6, and N7s

August 2017

Quick Start Guide

4.0 Installation drawings

Figure 3. Rosemount 214C Hazardous Location (00214-1030)

Andere Handbücher für Rosemount 214C

Inhaltsverzeichnis

Andere Emerson Zubehör Handbücher

Emerson

Emerson Micro Motion 7835 Bedienungsanleitung

Emerson

Emerson Rosemount 499ACL-02 Bedienungsanleitung

Emerson

Emerson Micro Motion Elite Coriolis Micro Motion Elite Coriolis... Bedienungsanleitung

Emerson

Emerson Micro Motion LF Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051S ERS Bedienungsanleitung

Emerson

Emerson Micro Motion H Series Bedienungsanleitung

Emerson

Emerson Micro Motion F Series Bedienungsanleitung

Emerson

Emerson MVS205 Kurzanleitung

Emerson

Emerson Rosemount 499AOZ Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 628 Bedienungsanleitung

Emerson

Emerson AVENTICS ST6 Bedienungsanleitung

Emerson

Emerson Fisher 249 Bedienungsanleitung

Emerson

Emerson Micro Motion H Series Bedienungsanleitung

Emerson

Emerson AVENTICS ST6 Bedienungsanleitung

Emerson

Emerson Marston Series Kurzanleitung

Emerson

Emerson Micro Motion F Series Bedienungsanleitung

Emerson

Emerson Rosemount 214C Bedienungsanleitung

Emerson

Emerson Rosemount 3300HT Bedienungsanleitung

Emerson

Emerson SpeedVue 430 Bedienungsanleitung

Emerson

Emerson Rosemount 398R Bedienungsanleitung

Emerson

Emerson Rosemount 499ACL-01 Bedienungsanleitung

Emerson

Emerson Net Safety SC311 Bedienungsanleitung

Emerson

Emerson Fisher 249VS Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung