Emerson Bettis SCE300 Bedienungsanleitung

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

July 2020

Bettis SCE300

Logic Board Firmware Upgrade Programmer ICD-U64 Procedure

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Notes

July 2020

This page intentionally left blank

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Table of Contents

July 2020

Table of Contents

Section 1: Firmware Upgrade

1.1 Tools ............................................................................................................. 1

1.2 ICD-U64 Programmer Preparation ................................................................ 3

1.3 Firmware Update .......................................................................................... 4

1.4 Firmware Upload........................................................................................... 4

1.5 Actuator Settings Checklist ......................................................................... 16

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Notes

July 2020

This page intentionally left blank

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 1

Section 1: Firmware Upgrade

This procedure details how to program rmware on the logic board for the Bettis SCE300

electric actuator using the ICD-U64 Programmer.

1.1 Tools

! WARNING

Installation, conguration, commissioning, maintenance, and repairs must be performed

by approved and qualied personnel only.

NOTICE

Certain nameplates may carry more than one approval, and each approval may have

unique installation/wiring requirements and/or conditions of "safe use", installation, and

maintenance. These special instructions are in addition to and may override the standard

installation procedures. Special instructions are listed by approval type.

To update the rmware of the SCE300 actuators, the following tools are necessary:

• PC with program CSSLOAD-CCS Programmer Control Software installed

(Figure 1). This software can be downloaded from:

http://www.ccsinfo.com/content.php?page=ccsloadsw

• PC with USB Drivers for all CSS programmers/debuggers

• Firmware “F02_63_125_v3_11.X.production”, for models E006, E013 or

latest revision

• Firmware “F02_250_500_v4_12.X.production”, for models E025, E051, E091,

E171 or latest revision

• The Universal programmer ICD-U64 (Figure 2)

• Logic Board or Actuator

• Cable from the ICD-U64 to the processor card rmware programming connector

part number: VA001-692-15

Figure 1

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade2

Section 1: Firmware Upgrade

Figure 2 ICD-U64 CCS Programmer

ICD-U64 USB Cable to PC

ICD-U64 USB Programmer

Coonector (Logic Board Side)

Figure 3 SCE300 Logic Board

Actuator size:

250/E025

500/E051

1000/E091

2000/E171

Programming

connector

Actuator size:

063/E006

125/E013

Table 1. Programming Connector Pinout

Signal ICD-U64 Pinout SCE300 Logic Board J15

Real Time Debugging Pin 1

ICSP Clock Pin 2 Pin 5

ICSP Data Pin 3 Pin 4

GND Ground Pin 4 Pin 3

VDD Power Pin 5 Pin 2

MCLR Pin 6 Pin 1

Large Logic Board Small Logic Board

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 3

Section 1: Firmware Upgrade

1.2 ICD-U64 Programmer Preparation

The ICD-U64 Programmer has an internal jumper to select multiple options to power the

target board (actuator logic board).

1. ICD-U64 programmer internal jumper selecting 5 V

This conguration allows the ICD-64 Programmer to provide power to the logic board.

This conguration can be used to program the logic board as standalone board or to

program the logic board while installed in the actuator. The rmware upgrade of the logic

board should be successful regardless if the logic board is powered from the actuator

power supply or ICD-U64 programmer.

Jumper select +5 V

2. ICD-U64 no jumper

The ICD-U64 internal jumper is not present or was set to no power the target board. It's

not possible to upgrade rmware in the logic board as a standalone board since no power

is being supplied to the target board. If the logic board is installed in the actuator, the

actuator requires to be powered on to have a successful rmware upgrade. Note that a

new programming tool will likely have this no voltage setting.

No jumper, or jumper selecting middle pin only

3. ICD-U64 programmer internal jumper selecting 3.3 V

This option must not be selected, it is not applicable for the SCE300 actuator.

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade4

Section 1: Firmware Upgrade

1.3 Firmware Update

After downloading the new rmware, the actuator settings will return to their default

values. As such, the settings in place prior to the rmware download will need to be set

again. For this reason, be sure to store the actuator settings (e.g. opening speed, closing

speed, % opening torque, % closing torque). Refer to Section 6.2 (Local Conguration of

the SCE300) in the actuator IOM for details. To be clear, all settings will be returned to the

factory default values, it is necessary to reset the open/close travel limits; also, the motor

will default to the smallest size.

If not correctly reset the unit will alarm in open torque.

OM1 settings are not required to be reset because they are unaffected by the processor

card rmware ash.

1.4 Firmware Upload

This procedure is based on the CCS Inc. CCSLOAD ICD-U64 programming tool- This tool can

power the microprocessor from the USB port of the PC, using the 5 V setting and also from

the actuator, using the actuators power source. The microprocessor to be ashed is referred

to as the “target”. Take care that the target is only powered from one source, not both.

In some eld installations is difcult to remove power from the actuator, this procedure

provides instructions in how to download rmware without removing the power from the

actuator, therefore instructions in the procedure must be followed to avoid any damage to

the actuator or any personal injury.

1. It is necessary to identify the position of the jumper inside the ICD-U64

programmer before downloading rmware as indicated in step 1.2.

2. To program the logic board as standalone board, connect the ICD-U64

programmer as shown in the picture and proceed in step 9.

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade 5

Section 1: Firmware Upgrade

3. To program the logic board as part of an actuator with no OM1 board present,

carefully connect the ICD-U64 programmer as shown in the pictures and proceed

in step 9.

Figure 4

4. To program the logic board as part of an actuator with an OM1 board present,

and the actuator is powered ON.

! CAUTION

Accessing the electronics compartment while the actuator is in service exposes the

technician to lethal voltage and possibly from more than one source.

Set the OM1 switch SW4 in ON position, it will prevent the actuator from stroking during

rmware download, and it will allow to maintain the actuator in the last position requested

by the 4 - 20 mA or the 0-10 V loop control.

Switch SW4 in

ON position

July 2020

Installation, Operation and Maintenance Manual

MAN-02-04-99-0739-EN Rev. 0

Firmware Upgrade6

Section 1: Firmware Upgrade

5. Note the position then remove the yellow position indicator to allow the OM1

board to be slightly moved to the side and have access to the programming

connector found in the actuator logic board.

6. Carefully remove the 4 screws that are holding the OM1 board. If the actuator is in

vertical position, there is a risk of dropping the screws inside the actuator. Dropping

the screws inside the actuator could cause a short circuit if the screws drop in the

power board, or a damage of the gears if the screws drop in the gears section.

OM1 board

screws

Andere Handbücher für Bettis SCE300

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson Dixell Wing XW570K Verdrahtungsschema

Emerson

Emerson 350 series Bedienungsanleitung

Emerson

Emerson ControlWave Bedienungsanleitung

Emerson

Emerson Bettis Multiport Bedienungsanleitung

Emerson

Emerson Tartarini FL Bedienungsanleitung

Emerson

Emerson FISHER 66 Bedienungsanleitung

Emerson

Emerson A36 Handbuch

Emerson

Emerson Alco Controls FSX Series Bedienungsanleitung

Emerson

Emerson FISHER SR8 Bedienungsanleitung

Emerson

Emerson Bettis RPX Series Bedienungsanleitung

Emerson

Emerson DanLoad 6000 Kurzanleitung

Emerson

Emerson Fisher 667 30 Bedienungsanleitung

Emerson

Emerson Shafer ECAT Bedienungsanleitung

Emerson

Emerson Fisher easy-Drive 200R Bedienungsanleitung

Emerson

Emerson Bettis GVO-C Series Bedienungsanleitung

Emerson

Emerson Fisher EZH Series Bedienungsanleitung

Emerson

Emerson TESCOM 04 Series Einrichtungshandbuch

Emerson

Emerson EC3-X32 Bedienungsanleitung

Emerson

Emerson Fisher 480 Series Bedienungsanleitung

Emerson

Emerson Fisher 627B Series Bedienungsanleitung

Emerson

Emerson Fisher L2e Bedienungsanleitung

Emerson

Emerson EIM 2000 Series Handbuch

Emerson

Emerson Bettis G01 Series Montageanleitung

Emerson

Emerson Bettis 500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung