Emerson E2 Bedienungsanleitung

quick start guide

Document Part # 026-4921 Rev 0 03-MAY-2012

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

E2 Setup with Carrier Corporations RTU Open

Controller for 527-0359

This document will guide you through setting up and commissioning the Carrier Corpora-

tions RTU Open Controller in the E2 controller (CARRIER OPN-RTUM Open Echelon device in

the E2).

E2 and Echelon Devices Communications Network Wiring Diagram

Note that Open Echelon Description files require E2 firmware version 3.01FO1 or higher.

Figure 1 - Network Wiring Diagram

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 2 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

Controller Board Echelon Network Cable Connections

Carrier Corporations RTU Open Controller Board (SW3) Dip Switch Set-

tings

Set SW3 Dip Switches As Shown

BAUD RATE DS-1 DS-2 DS-3 DS-4 DS-5 DS-6 DS-7 DS-8

38.4K baud ON OFF OFF ON OFF ON ON OFF

Figure 2 - Echelon Network Cable Connections

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 3 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

Third Party Hardware Configuration Notation

The RTU Opens operation depends upon its occupancy state (Occupied/Unoccupied). The

RTU Open operates continuously in the Occupied Mode by default until the occupancy

schedule has been configured.

NOTE: The controllers OCCUPANCY SOURCE point setting must be initiated through the

Third Party hardware and software setup procedures in order for any Building Automation

System (BAS) to control Occupancy Schedule.

The OCCUPANCY SOURCE point setting must be configured as follows:

3 = BAS ON/OFF

STEP 1: Upload the description file to the E2 controller.

1. From UltraSite, connect to your E2 controller.

2. Right-click the E2 icon and select Description File Upload.

3. Browse to the location of the description file and click Upload.

4. After uploading, you will need to reboot the E2 controller.

Figure 3 - Description File Upload

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 4 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

STEP 2: Activate the license of the device.

5. From the E2 front panel (or via the Terminal Mode), press , 7(System Configura-

tion), and 9(Licensing).

6. Press F1 (ADD FEATURE) and enter your license key.

STEP 3: Once the license is activated, add the device to the E2 controller.

7. Press , 7(System Configuration), 7(Network Setup), 2(Connected I/O Boards &

Controllers).

8. Press F2 (NEXT TAB) to go to the C4: Third Party tab. You should see the device in the list.

Enter the number of devices to add and press the button to save your changes.

Figure 4 - Add License Screen

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 5 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

Figure 5 - Specify the Number of Devices to Add

Figure 6 - Device Setup Screen

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 6 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

STEP 4: Commission the Echelon device.

9. Press , 7(System Configuration), 7(Network Setup), 1(Network Summary).

10.Use the UP and DOWN arrow keys to highlight the device name and then press 

(Commission).

11.Select the method to use for identifying the device. Select from the list:

1 = Service Pin --> The physical button on the controller must be pressed. This is the

preferred method for device accuracy.

2 = Entering Neuron ID(s) directly --> Echelon device address should consist of 12

characters. The device is identified via remote communication using the Neuron ID.

Use this selection if the Neuron ID of the device is available.

3 = Specifying a range of nodes --> The network is scanned for neuron addresses.

Figure 7 - Commission the Device

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 7 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

Figure 8 - Select Method for Identifying the Controller

Figure 9 - Identifying the Controller Using the Neuron ID

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 8 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

STEP 5: Name the controller device.

12.Press , 7(System Configuration), 7(Network Setup), 1(Network Summary).

13.Use the UP and DOWN arrow keys to highlight the generic LonMark Device name and

then Press (SETUP).

14.Enter the desired device name in the Name field highlighted and then press the to

return to the Network Summary screen.

NOTE: By default, any Third Party (Open Echelon) devices that are initiated in E2 will always

have a generic naming sequence as shown:

Example: LONMARK_001, LONMARK_002, LONMARK_003

Figure 10 - Network Summary Screen

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 9 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

Figure 11 - Changing the Device Name

Figure 12 - Changing the Device Name

E2 Setup with Carrier Corporations RTU Open Controller for 527-0359

Document Part # 026-4921 Rev 0 03-MAY-2012 Page 10 of 14

Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.

quick start guide

STEP 6: View the device Status Screen.

15.Press and then 5(Configured Applications). A list of all configured applications in

E2 displays on the screen.

16.Use the UP and DOWN arrow keys to highlight the device name on the Configured Appli-

cations screen and then press . The device Status Screen displays.

NOTE: By default, if there are one or more devices of the same type configured in E2, a list of

all common devices will display (Summary Screen) in reference to the numeric or alphanu-

meric character sequence of the devices labeled.

Example: AHU-1, AHU-2, AHU-3, RTU-1, RTU-2, RTU-3

Figure 13 - Network Summary Screen

Andere Handbücher für E2

Andere Emerson Controller Handbücher

Emerson

Emerson Bettis CBA*30-SR series Betriebsanleitung

Emerson

Emerson Asco Sentronic LP 617 Series Bedienungsanleitung

Emerson

Emerson DIXELL XR77CHC Bedienungsanleitung

Emerson

Emerson FloBoss 107 Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC6200 HW2 Konfigurationshandbuch

Emerson

Emerson Fisher FIELDVUE DVC6200 HW2 Konfigurationshandbuch

Emerson

Emerson Fisher 64 Series Bedienungsanleitung

Emerson

Emerson Fisher 133H Bedienungsanleitung

Emerson

Emerson DIXELL XR30T Verdrahtungsschema

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS Bedienungsanleitung

Emerson

Emerson Fisher L2 Bedienungsanleitung

Emerson

Emerson dixell XR60CX Verdrahtungsschema

Emerson

Emerson Alco Controls EC3 Series Bedienungsanleitung

Emerson

Emerson Alco Controls CS1 Series Bedienungsanleitung

Emerson

Emerson FloBoss 107 Bedienungsanleitung

Emerson

Emerson Tarantini MN Kurzanleitung

Emerson

Emerson Fisher 67C Series Bedienungsanleitung

Emerson

Emerson Fisher Y696VR Series Bedienungsanleitung

Emerson

Emerson Site Supervisor Bedienungsanleitung

Emerson

Emerson Bettis XTE3000 Bedienungsanleitung

Emerson

Emerson Dixell IEV22D Bedienungsanleitung

Emerson

Emerson Fisher 2502 Bedienungsanleitung

Emerson

Emerson Bettis TEC2 Bedienungsanleitung

Emerson

Emerson E2 RX Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung