Emerson PACSystems IPC 2010 Bedienungsanleitung

Quick Start Guide

GFK-3268A

Oct 2023

PACSystems™IPC 2010

QUICK START GUIDE

 
iPACSystems™IPC 2010 GFK-3268A 
Contents 
Initial Checks .................................................................1 
Front Panel Description ..................................................2 
Power-Input......................................................................................3 
Serial Console..................................................................................6 
Secure Shell (SSH)..........................................................................7 
IP-Addresses ................................................................................... 7 
Pre-Installed Software Images ........................................8 
Ubuntu Server Quick Start...............................................................9 
Default User and Passwords ...................................................9 
Networking Configuration ......................................................10 
Additional network configuration............................................11 
PACEdge Quick Start ....................................................................12 
Getting Started.......................................................................13 
Initial Login.............................................................................13 
Additional Information .................................................17 
WiFi/Cellular Extension..................................................................17 
WiFi/Cellular Module with PACEdge .....................................17 
Overtemperature Alarm .................................................................17 
LED Control ...................................................................................18 
Accessing the Boot Loader............................................................18 
Additional Information .................................................19 
General Contact Information..........................................................19 
 

1PACSystems™IPC 2010 GFK-3268A

Initial Checks

Upon receiving your equipment, carefully inspect all shipping containers

for damage. If any part of the system is damaged, notify the carrier

immediately. The damaged shipping container should be saved as

evidence for inspection by the carrier.

As the consignee, it is your responsibility to register a claim with the

carrier for damage incurred during shipment. Emerson will fully

cooperate with you, however, should such action be necessary.

After unpacking the equipment, record all serial numbers. Serial numbers

are required if you should need to contact Customer Care during the

warranty period. All shipping containers and all packing material should

be saved should it be necessary to transport or ship any part of the

system.

Verify that all components of the system have been received and that

they agree with your order. If the system received does not agree with

your order, contact Customer Care.

2PACSystems™IPC 2010 GFK-3268A

Front Panel Description

Figure 1: Overview

Number

Description

Power & Temperature LED

µSD Card slot

USB-C port

Serial port

USB ports

Ethernet ports

Power Connector

3PACSystems™IPC 2010 GFK-3268A

Power-Input

To power the system, a voltage of 24 V DC must be supplied to the

power connector. The IPC 2010 power supply must meet the

requirements for SELV (safety extra-low voltage)/LPS (limited power

source) or ES1/PS2 appropriately rated for the ambient and altitude of

the application. There are no buttons for power or resetting, as the system will

start automatically once power is applied. The Power LED (1) will light up green

to indicate that the system is now powered on.

The specific plug required is a Phoenix Contact with the part number

1748367, and users must use the same connector type

Figure 2: Power Input

Signal Name

Pin (left to right)

FGND

Power –24VDC (10-30VDC)

Power + 24VDC (10-30VDC)

4PACSystems™IPC 2010 GFK-3268A

CAUTION

Equipment is intended for installation in Restricted Access Area.

Les matériels sont destinés à être installés dans des

EMPLACEMENTS À ACCÈS RESTREINT.

Battery

The IPC 2010 contains a CR2032 lithium coin battery. It is a industrial

CR2032 (-40°C to 125°C) battery and is accessible on the right side of

the IPC 2010. Depending on the operating hours and temperature, the

estimated battery life is 2 to 10 years. Battery current is not used when

the IPC 2010 is supplied with 24V.

5PACSystems™IPC 2010 GFK-3268A

Battery Maintenance

To replace the battery, pull the battery holder (on the right side of the

system) out of the system, replace the battery and insert the battery

holder back into the system.

Figure 3: Battery Removal

CAUTION

- Only replace with CR2032 battery. Batteries may explode if

mistreated. Do not charge, disassemble, or incinerate.

- Remplacer uniquement par une pile CR2032. Les piles peuvent

exploser si elles sont maltraitées. Ne pas charger, démonter ou

incinérer.

6PACSystems™IPC 2010 GFK-3268A

Serial Console

To gain access to the system, utilize the serial console port (4) by

connecting it to the host PC’s RS232 interface using a null modem cable.

Once connected, the host can establish a connection by running a

terminal emulator such as HyperTerminal or minicom. The default serial

port parameters are 115200, 8N1

The connector is RJ-45 style with pinout as defined in EIA/TIA-561, so

that off-the-shelf adapters to DB9 or USB can be used.

The pinout for RJ-45 (8P8C) connector is defined as follows:

Signal

RJ-45 Pin

GND

RxD

TxD

Once a serial connection is established, it can be used to determine an

IP address that was assigned by DHCP server, using command: ip addr

7PACSystems™IPC 2010 GFK-3268A

Secure Shell (SSH)

To establish a connection with the system, Ethernet can be used instead

of the serial console. The system has an SSH server running on port 22,

and the default IP address settings are described below.

To connect to the system, use Putty on a Windows host or the default

SSH tools on Linux.

The login credentials will vary depending on the pre-installed software

*Ubuntu Linux or PACEdge), so it is advised to refer to the sections

below for specific details.

IP-Addresses

On preinstalled systems the second ethernet interface (Port 2) is

configured to use the static IP-Address: 192.168.3.100 and DHCP as

well. Therefore (if the second ethernet interface is connected to a DHCP

server) two IP-Addresses are usable on this interface (IP-Address

provided by DHCP server and static IP-Address 192.168.3.100).

CAUTION

MULTIPLE DEVICES WITH THE SAME IP ADDRESS ON THE SAME

NETWORK CAN LEAD TO ADDRESS CONFLICTS WITH UNPREDICTABLE

BEHAVIOR.

If you are using several microIPC devices in the same network, it is strongly

recommended to change the static IP Address.

8PACSystems™IPC 2010 GFK-3268A

Pre-Installed Software Images

IPC 2010 comes with two pre-installed software options:

•Ubuntu Server 20.04.05 LTS

•PACEdge v2.3.0 (based on Ubuntu 20.04 Server)

Depending on pre-installed software login credentials and some of the

configuration tasks are different. Sections bellow will guide through the

getting started process for each of these software options.

Andere Handbücher für PACSystems IPC 2010

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount CCO 5500 Bedienungsanleitung

Emerson

Emerson FB1200 Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Rosemount 1181pH TRANSMITTER Bedienungsanleitung

Emerson

Emerson Rosemount WPG Bedienungsanleitung

Emerson

Emerson Micro Motion LNG Series Kurzanleitung

Emerson

Emerson Rosemount 3818 Programmierhandbuch

Emerson

Emerson Micro Motion TA Series Bedienungsanleitung

Emerson

Emerson Net Safety Millennium Bedienungsanleitung

Emerson

Emerson Penberthy Multiview Handbuch

Emerson

Emerson Rosemount 3414 Bedienungsanleitung

Emerson

Emerson Rosemount 1595 Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson EC2-XC645CX Verdrahtungsschema

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount Clarity II T56 Bedienungsanleitung

Emerson

Emerson X-STREAM Series Bedienungsanleitung

Emerson

Emerson Rosemount 56 Bedienungsanleitung

Emerson

Emerson FB1100 Stücklistenhandbuch

Emerson

Emerson FloBoss 107 Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson MRLDS-250 Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung