Emerson AMS 2140 Bedienungsanleitung

Optional – Job Storage

Alignment jobs can also be saved and printed.

This is found under “Job Manager” on the ALT screen

of the main menu.

You can customize

the machine

graphics using a

selection of

different machine

types. Consult the

user manual for

additional details,

advanced functions,

and instructions.

Pocket Guide

For Laser Shaft Alignment

AMS 2140

Machinery Health™Analyzer

Refer to the user

manual to learn

how to upload

saved jobs back to

the PC software.

Introduction:

This guide outlines a quick and easy 3-step

method for precision shaft alignment.

Set-up:

Choose the shortest support posts that will still

allow the laser beam to pass over or through the

coupling. Mount the laser xtures by sliding each

head over the support posts and locking them

into place with the yellow clamping levers.

Mount laser heads as shown above, being careful

to mount the laser on the stationary machine.

Sweep Size:

The “Auto Sweep” method provides a simple,

accurate solution for any alignment task. Start

anywhere. Stop anywhere. While it is always best

to completely rotate the shaft, this method can

be used effectively with partial sweeps down to

45°. Press [ENTER] to retrieve data via Bluetooth.

45°

Operating Notes:

Laser ﬁxtures are for shaft alignment only and

should be operated by properly trained personnel.

As precision instruments, care should be taken to

not subject them to shock.

Laser Safety:

Do not stare directly into the laser beam!

[NOTE: Red LED on Laser Head indicates that

laser is active.]

Do not insert optical

devices into beam.

P/N: MHM-97109, rev 1

Mount laser on

stationary machine

Mount sensor on

machine to be moved

AMS 2140 Machinery Health™Analyzer

Optional: Foot Pre-Check

To check foot condition, press [F12] before

sweeping laser ﬁxtures and follow on-screen

instructions. Use a feeler gauge to determine

required shim correction. The Soft Foot option

provides you with a sense of severity without

showing numbers. The FDI option will provide an

estimate of the required shim.

Bluetooth Set- Up

1. Press [Home] > [F5] Comm Setup >

[F7] Bluetooth Setup.

2. Press [F2] Bluetooth to enable or disable the

Bluetooth radio. When the radio is enabled,

the Bluetooth LED on the top of the analyzer

turns on and the icon appears in the upper corner

of the screen.

3. Press [F7] Pair to pair the sensor.

“Paired” appears next to the device

once the laser heads are connected

to the analyzer. To differentiate

between laser heads and

headphones, a laser image as shown to the right

is displayed next to the serial number.

1 Enter Dimensions 2 Sweep Laser Heads 3 Move Machine

Values for A, B, E and

RPM are required.

Use [<] and [>] to

move between elds.

Optional machines

types enable entry of

values for C and D for

the other machine.

Note: Use [./] to

calculate fractions.

Example: 30 3/8 = [3]

[0] [./] [3] [./] [./] [8]

Press [ENTER]

to initialize

laser xtures.

The Vertical

Machine Move

indicates how much

to shim/drop each

machine foot.

Sweep laser heads.

Start anywhere.

Stop anywhere.

Minimum

recommended

sweep size is 45°.

Press [ENTER]

to retrieve data

via Bluetooth.

When viewing the

Horizontal Move

screen, press [F12]

for ‘LIVE MOVE’.

Place laser xtures

in desired position

and press [ENTER]

to start.

OK = Good

X = Soft

Display Meaning

Way out.

More than 2x tolerance.

Getting close.

1-2x tolerance.

Good job!

Below acceptable tolerance.

Great job!

Below excellent tolerance.

Shaft Alignment Indicator

The bull’s eye display continuously updates

alignment status.

Emerson

Reliability Solutions

835 Innovation Drive

Knoxville, TN 37932 USA

+1 865 675 2400

www.emerson.com/ams

XX = Bad

XXX = Extreme

Andere Handbücher für AMS 2140

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount Analytical 400A Bedienungsanleitung

Emerson

Emerson MicroMotion HPC010 Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson FB1100 Bedienungsanleitung

Emerson

Emerson AMS 2140 Bedienungsanleitung

Emerson

Emerson Rosemount 3812 Bedienungsanleitung

Emerson

Emerson FB2200 Bedienungsanleitung

Emerson

Emerson NGA 2000 TO2 Bedienungsanleitung

Emerson

Emerson Rosemount TCL Bedienungsanleitung

Emerson

Emerson Micro Motion 7835 Bedienungsanleitung

Emerson

Emerson Rosemount 485 Annubar Bedienungsanleitung

Emerson

Emerson Micro Motion GDM Bedienungsanleitung

Emerson

Emerson Rosemount Bedienungsanleitung

Emerson

Emerson Rosemount 3812 Programmierhandbuch

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Daniel 3818 Bedienungsanleitung

Emerson

Emerson Rosemount 3051SAL Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson LMS1000 Bedienungsanleitung

Emerson

Emerson Rosemount 1195 Bedienungsanleitung

Emerson

Emerson AL200 Bedienungsanleitung

Emerson

Emerson Micro Motion TA Series Bedienungsanleitung

Emerson

Emerson FloBoss 103 Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung