Emerson Rosemount 8800D Series Bedienungsanleitung

Quick Start Guide

00825-0100-4004, Rev FG

August 2020

Rosemount™ 8800D Series Vortex Flow

Meter

Contents

About this guide...........................................................................................................................3

Return policy................................................................................................................................6

Emerson Flow customer service................................................................................................... 7

Pre-installation.............................................................................................................................8

Basic installation.........................................................................................................................21

Basic configuration.....................................................................................................................40

Safety instrumented systems installation................................................................................... 49

Product certifications................................................................................................................. 50

Quick Start Guide August 2020

2 Rosemount™ 8800D Series Vortex Flow Meter

1 About this guide

This guide provides basic installation and configuration instructions for the

Rosemount™ 8800D Series Vortex Flow meters with single, dual, or quad

transmitters.

For more information on installation and configuration instructions,

diagnostics, maintenance, service, and troubleshooting for:

•Foundation Fieldbus devices consult 00809-0100-4772 Manual

•Non-MultiVariable meters and meters with the MTA option code for

HART and all Foundation Fieldbus devices, please consult

00809-0100-4004 Manual

For more information on installation and configuration instructions,

diagnostics, maintenance, service, and troubleshooting, for meters with the

MPA or MCA option code, please consult 00809-1100-4004 Manual.

For hazardous location installation, including Explosion-proof, Flameproof,

or Intrinsic Safety (I.S.), please consult 00825-VA00-0001 Approval

Document.

1.1 Hazard messages

This document uses the following criteria for hazard messages based on

ANSI standards Z535.6-2011 (R2017).

DANGER

Serious injury or death will occur if a hazardous situation is not avoided.

WARNING

Serious injury or death could occur if a hazardous situation is not avoided.

CAUTION

Minor or moderate injury will or could occur if a hazardous situation is not

avoided.

NOTICE

Data loss, property damage, hardware damage, or software damage can

occur if a situation is not avoided. There is no credible risk of physical injury.

August 2020 Quick Start Guide

Quick Start Guide 3

Physical access

NOTICE

Unauthorized personnel can potentially cause significant damage and/or

misconfiguration of end users' equipment. Protect against all intentional or

unintentional unauthorized use.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access to protect

users' assets. This is true for all systems used within the facility.

1.2 Safety messages

WARNING

Explosion hazards. Failure to follow these instructions could cause an

explosion, resulting in death or serious injury.

•Verify the operating atmosphere of the transmitter is consistent with the

appropriate hazardous locations certifications.

•Installation of this transmitter in an explosive environment must be in

accordance with the appropriate local, national, and international

standards, codes, and practices. Review the approvals documents for

any restrictions associated with a safe installation.

•Do not remove transmitter covers or thermocouple (if equipped) in

explosive atmospheres when the circuit is live. Both transmitter covers

must be fully engaged to meet explosion-proof requirements.

•Before connecting a hand-held communicator in an explosive

atmosphere, make sure the instruments in the loop are installed in

accordance with intrinsically safe or non-incendive field wiring practices.

WARNING

Electrical shock hazard. Failure to follow this instruction could result in death

or serious injury. Avoid contact with the leads and terminals. High voltage

that may be present on leads can cause electrical shock.

Quick Start Guide August 2020

4 Rosemount™ 8800D Series Vortex Flow Meter

WARNING

General hazard. Failure to follow these instructions could result in death or

serious injury.

•This product is intended to be used as a flowmeter for liquid, gas, or

steam applications. Do not use for any other purpose.

•Make sure only qualified personnel perform the installation.

August 2020 Quick Start Guide

Quick Start Guide 5

2 Return policy

Emerson procedures must be followed when returning equipment. These

procedures ensure legal compliance with government transportation

agencies and help provide a safe working environment for Emerson

employees. Failure to follow Emerson procedures will result in your

equipment being refused delivery.

Quick Start Guide August 2020

6 Rosemount™ 8800D Series Vortex Flow Meter

3 Emerson Flow customer service

Email:

•Worldwide: [email protected]

•Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800 522 6277 U.K. 0870 240

1978

Australia 800 158 727

Canada +1 303 527

5200

The

Netherlands

+31 (0) 704

136 666

New Zealand 099 128 804

Mexico +41 (0) 41

7686 111

France 0800 917 901 India 800 440 1468

Argentina +54 11 4837

7000

Germany 0800 182

5347

Pakistan 888 550 2682

Brazil +55 15 3413

8000

Italy 8008 77334 China +86 21 2892

9000

Venezuela +58 26 1731

3446

Central &

Eastern

Europe

+41 (0) 41

7686 111

Japan +81 3 5769

6803

Russia/CIS +7 495 995

9559

South Korea +82 2 3438

4600

Egypt 0800 000

0015

Singapore +65 6 777

8211

Oman 800 70101 Thailand 001 800 441

6426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 0444

0684

August 2020 Quick Start Guide

Quick Start Guide 7

4 Pre-installation

4.1 Planning

For a successful installation, consider each aspect of your application and the

meter you are installing.

4.1.1 Sizing

To determine the correct meter size for optimal flow meter performance:

•Determine the limits of measuring flow.

•Determine the process conditions so that they are within the stated

requirements for Reynolds number and velocity.

For sizing details, refer to the product reference manual.

Sizing calculations are required to select the proper flow meter size. These

calculations provide pressure loss, accuracy, and minimum and maximum

flow rate data to guide in proper selection. Vortex sizing software can be

found using the Selection and Sizing tool. The Selection and Sizing tool can

be accessed online or downloaded for offline use using this link:

www.Emerson.com/FlowSizing.

4.1.2 Wetted material selection

Ensure that the process fluid is compatible with the meter body wetted

materials when specifying the Rosemount 8800D. Corrosion will shorten the

life of the meter body. Consult recognized sources of corrosion data or

contact Emerson Flow Sales Representative for more information.

Note

If Positive Material Identification (PMI) is required, perform test on a

machined surface.

4.1.3 Orientation

The best orientation for the meter depends on the process fluid,

environmental factors, and any other nearby equipment.

Vertical installation

Vertical, upward, installation allows upward process liquid flow and is

generally preferred. Upward flow ensures that the meter body always

remains full and that any solids in the fluid are evenly distributed.

The meter can be mounted in the vertical down position when measuring

gas or steam flows. This type of application is strongly discouraged for liquid

flows, although it can be done with proper piping design.

Quick Start Guide August 2020

8 Rosemount™ 8800D Series Vortex Flow Meter

Figure 4-1: Vertical installation

A B

A. Liquid or gas flow

B. Gas flow

Note

To ensure the meter body remains full, avoid downward vertical liquid flows

where back pressure is inadequate.

Horizontal installation

For horizontal installation, the preferred orientation is to have the

electronics installed to the side of the pipe. In liquid applications, this helps

prevent any entrained air or solids from striking the shedder bar and

disrupting the shedding frequency. In gas or steam applications, this helps

prevent any entrained liquid (such as condensate) or solids do not strike the

shedder bar and disrupt the shedding frequency.

Figure 4-2: Horizontal installation

A. Preferred installation—meter body installed with electronics to side of

pipe

B. Acceptable installation—meter body installed with electronics above pipe

August 2020 Quick Start Guide

Quick Start Guide 9

High-temperature installations

The maximum process temperature for integral electronics is dependent on

the ambient temperature where the meter is installed. The electronics must

not exceed 185 °F (85 °C).

Figure 4-3 shows combinations of ambient and process temperatures

needed to maintain a housing temperature of less than 185 °F (85 °C).

Figure 4-3: Ambient/Process temperature limits

200 (93)

180(82)

160 (71)

140 (60)

120 (49)

100 (38)

80 (27)

60 (16)

200 (93)

300 (149)

400 (204)

500 (260)

600 (316)

700 (371)

800 (427)

900 (482)

1000 (538)

100 (38)

A. Ambient temperature °F (°C)

B. Process temperature °F (°C)

C. 185 °F (85 °C) Housing temperature limit.

Note

The indicated limits are for horizontal pipe and vertical meter position, with

meter and pipe insulated with 3 in. (77 mm) of ceramic fiber insulation.

Install the meter body so the electronics are positioned to the side of the

pipe or below the pipe as shown in Figure 4-4. Insulation may also be

required around the pipe to maintain an electronics temperature below

185 °F (85 °C). See Figure 5-2 for special insulation considerations.

Quick Start Guide August 2020

10 Rosemount™ 8800D Series Vortex Flow Meter

Andere Handbücher für Rosemount 8800D Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson World Class 3000 Bedienungsanleitung

Emerson

Emerson Rosemount 6888Xi Bedienungsanleitung

Emerson

Emerson Rosemount 1057 Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Emerson

Emerson ROSEMOUNT 485 Annubar Pak-Lok Bedienungsanleitung

Emerson

Emerson Rosemount CT5400 Bedienungsanleitung

Emerson

Emerson Rosemount Bedienungsanleitung

Emerson

Emerson 8800C Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Wireless Field Link Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson Rosemount 3414 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 3410 Series Programmierhandbuch

Emerson

Emerson LMS1000 Bedienungsanleitung

Emerson

Emerson Rosemount 1195 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson MICRO MOTION HFVM Series Kurzanleitung

Emerson

Emerson Micro Motion G-Series Bedienungsanleitung

Emerson

Emerson FloBoss 103 Bedienungsanleitung

Emerson

Emerson Rosemount CT5100 Bedienungsanleitung

Emerson

Emerson Rosemount FCL Bedienungsanleitung

Emerson

Emerson Rosemount 9175 Bedienungsanleitung

Emerson

Emerson Daniel Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung