Emerson Micro Motion G-Series Bedienungsanleitung

Installation Manual

00825-0100-4630, Rev AA

October2023

Micro Motion™ G-Series Coriolis Flow and

Density Sensors

Safety messages

Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety

message carefully before proceeding to the next step.

Safety and approval information

This Micro Motion product complies with all applicable European directives when properly installed in accordance

with the instructions in this manual. Refer to the EU Declaration of Conformity for directives that apply to this

product. The following are available: the EU Declaration of Conformity, with all applicable European directives, and the

complete ATEX installation drawings and instructions. In addition, the IECEx installation instructions for installations

outside of the European Union and the CSA installation instructions for installations in North America are available at

Emerson.com or through your local Micro Motion support center.

Information affixed to equipment that complies with the Pressure Equipment Directive, can be found at

Emerson.com. For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not

apply.

Other information

Troubleshooting information can be found in the appropriate Configuration and Use Manual. Product data sheets and

manuals are available from the Micro Motion website at Emerson.com.

Return policy

Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with

government transportation agencies and help provide a safe working environment for Micro Motion employees.

If you fail to follow Micro Motion procedures, then Micro Motion will not accept your returned equipment.

Return procedures and forms are available on our web support site at Emerson.com, or by calling the Micro Motion

Customer Service department.

Contents

Chapter 1 Before you begin....................................................................................................................... 5

1.1 About this document.................................................................................................................. 5

1.2 Hazard messages........................................................................................................................ 5

1.3 Related documentation.............................................................................................................. 6

Chapter 2 Planning..................................................................................................................................... 7

2.1 Installation checklist....................................................................................................................7

2.2 Best practices...............................................................................................................................8

2.3 Temperature limits......................................................................................................................8

Chapter 3 Mounting..................................................................................................................................11

3.1 Mount the sensor...................................................................................................................... 11

Chapter 4 Wiring....................................................................................................................................... 13

4.1 Options for wiring..................................................................................................................... 13

4.2 Connect 4-wire cable.................................................................................................................13

Chapter 5 Grounding................................................................................................................................ 19

Chapter 6 Supplementary information.................................................................................................. 21

6.1 Pressure relief............................................................................................................................21

Installation Manual Contents

00825-0100-4630 October2023

Installation Manual 3

Contents Installation Manual

October2023 00825-0100-4630

4 Micro Motion G-Series

1 Before you begin

1.1 About this document

This document provides information on planning, mounting, wiring, and grounding the

G-Series sensor.

The information in this document assumes that users understand basic transmitter and

sensor installation, configuration, and maintenance concepts and procedures.

1.2 Hazard messages

This document uses the following criteria for hazard messages based on ANSI standards

Z535.6-2011 (R2017).

DANGER

Serious injury or death will occur if a hazardous situation is not avoided.

WARNING

Serious injury or death could occur if a hazardous situation is not avoided.

CAUTION

Minor or moderate injury will or could occur if a hazardous situation is not avoided.

NOTICE

Data loss, property damage, hardware damage, or software damage can occur if a

situation is not avoided. There is no credible risk of physical injury.

Physical access

WARNING

Unauthorized personnel can potentially cause significant damage and/or

misconfiguration of end users' equipment. Protect against all intentional or unintentional

unauthorized use.

Physical security is an important part of any security program and fundamental to

protecting your system. Restrict physical access to protect users' assets. This is true for all

systems used within the facility.

Installation Manual Before you begin

00825-0100-4630 October2023

Installation Manual 5

1.3 Related documentation

You can find all product documentation at https://www.emerson.com/en-ca/automation/

micro-motion.

See any of the following documents for more information:

•The hazardous area approvals documentation shipped with the sensor or available

at www.emerson.com/flowmeasurementhttps://www.emerson.com/en-ca/automation/

micro-motion.

•Micro Motion G-Series Flow and Density Meters Product Data Sheet

•Micro Motion 9-Wire Flowmeter Cable Preparation and Installation Manual

•The transmitter installation guide and the transmitter configuration and use guide

Before you begin Installation Manual

October2023 00825-0100-4630

6 Micro Motion G-Series

2 Planning

2.1 Installation checklist

□Make sure that the hazardous area specified on the approval tag is suitable for the

environment in which the meter will be installed.

WARNING

Failure to abide by approvals can cause an explosion resulting in injury or death.

□Verify that the local ambient and process temperatures are within the limits of the

meter.

□If your sensor has an integral transmitter, no wiring is required between the sensor

and transmitter. Follow the wiring instructions in the transmitter installation manual for

signal and power wiring.

□If your transmitter has remote-mounted electronics, follow the instructions in this

manual for wiring between the sensor and the transmitter, and then follow the

instructions in the transmitter installation manual for power and signal wiring.

Table 2-1: Maximum cable lengths

Cable type To transmitter Maximum length

Micro Motion

9-wire

5700 transmitter 1,000ft (305m)

All other MVD transmitters 60ft (18m)

Micro Motion

4-wire

All 4-wire MVD transmitters 1,000ft (305m) without Ex-approval

500ft (152m) with IIC-rated sensors

1,000ft (305m) with IIB-rated sensors

Table 2-2: Maximum lengths for user-supplied 4-wire cable

Wire function Wire size Maximum length

Power (VDC) 22AWG (0.326mm²) 300ft (91m)

20AWG (0.518mm²) 500ft (152m)

18AWG (0.823mm²) 1,000ft (305m)

Signal (RS-485) 22AWG (0.326mm²) or larger 1,000ft (305m)

□For optimal performance, install the sensor in the preferred orientation. The sensor will

work in any orientation as long as the flow tubes remain full of process fluid.

Installation Manual Planning

00825-0100-4630 October2023

Installation Manual 7

Table 2-3: Preferred sensor orientation

Process Preferred orientation Secondary preferred

orientation

Alternate suitable

orientation

Liquids &&

slurries

Gases

□Install the meter so that the flow direction arrow on the sensor case matches the actual

forward flow of the process. (Flow direction is also software-selectable.)

2.2 Best practices

•There are no pipe run requirements for Micro Motion sensors. Straight runs of pipe

upstream or downstream are unnecessary.

•If the sensor is installed in a vertical pipeline, liquids and slurries should flow upward

through the sensor.

•Keep the sensor tubes full of process fluid.

•For halting flow through the sensor with a single valve, install the valve downstream

from the sensor.

•The sensor does not require external supports. The flanges will support the sensor in

any orientation.

2.3 Temperature limits

Sensors can be used in the process and ambient temperature ranges shown in the

temperature limit graphs. For the purposes of selecting electronics options, temperature

limit graphs should be used only as a general guide. If your process conditions are close to

the gray area, consult technical support.

WARNING

Temperature limits may be further restricted by hazardous area approvals that are

necessary to avoid potential injury to personnel and damage to equipment. Refer to the

hazardous area approvals documentation shipped with the sensor for specific

temperature ratings for each model and configuration.

Note

In all cases, the electronics cannot be operated where the ambient temperature is below

-40°F (-40.0°C) or above 140°F (60.0°C). If a sensor is to be used where the ambient

temperature is outside of the range permissible for the electronics, the electronics must

Planning Installation Manual

October2023 00825-0100-4630

8 Micro Motion G-Series

be remotely located where the ambient temperature is within the permissible range, as

indicated by the shaded areas of the temperature limit graphs.

Ambient and process temperature limits for all G-Series meters

Tamb = Ambient temperature °F (°C)

Tproc = Process temperature °F (°C)

A = All available electronic options

B = Remote mount electronics only

Installation Manual Planning

00825-0100-4630 October2023

Installation Manual 9

Planning Installation Manual

October2023 00825-0100-4630

10 Micro Motion G-Series

Inhaltsverzeichnis

Andere Emerson Messgerät Handbücher

Emerson

Emerson Rosemount 2410 Bedienungsanleitung

Emerson

Emerson RXi HMI Bedienungsanleitung

Emerson

Emerson Rosemount 56 Bedienungsanleitung

Emerson

Emerson Rosemount BINOS 100 F Bedienungsanleitung

Emerson

Emerson ControlWave EFM 4710A Bedienungsanleitung

Emerson

Emerson Rosemount 0085 Bedienungsanleitung

Emerson

Emerson Rosemount 3814 Bedienungsanleitung

Emerson

Emerson Rosemount 928 Bedienungsanleitung

Emerson

Emerson DIXELL XWEB1000D PRO Verdrahtungsschema

Emerson

Emerson PENBERTHY LC Series Handbuch

Emerson

Emerson FB1100 Bedienungsanleitung

Emerson

Emerson Rosemount 6888C Bedienungsanleitung

Emerson

Emerson PACSystems IPC 2010 Bedienungsanleitung

Emerson

Emerson Rosemount 6888A Bedienungsanleitung

Emerson

Emerson Fisher 4320 Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Rosemount FCL Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson RTM-ATCA-736x-DD Bedienungsanleitung

Emerson

Emerson Rosemount 54eA Bedienungsanleitung

Emerson

Emerson CSI 2140 Bedienungsanleitung

Emerson

Emerson Rosemount Analytical RDO Bedienungsanleitung

Emerson

Emerson Rosemount 8800D Series Bedienungsanleitung

Emerson

Emerson Daniel 3410 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung