Emerson Rosemount 3051 CF Series Bedienungsanleitung

Quick Start Guide

00825-0100-4797, Rev HA

January 2020

Rosemount™ 3051 Pressure Transmitter

and Rosemount 3051CF Series Flow

Meter

with PROFIBUS® PA Protocol

Contents

About this guide...........................................................................................................................3

Transmitter installation................................................................................................................ 5

Basic configuration.....................................................................................................................26

Trim the transmitter...................................................................................................................29

Product certifications................................................................................................................. 30

Quick Start Guide January 2020

2 Emerson.com/Rosemount

1 About this guide

This guide provides basic guidelines for Rosemount 3051 Transmitters. It

does not provide instructions for configuration, diagnostics, maintenance,

service, troubleshooting, Explosion-Proof, Flame-Proof, or intrinsically safe

(I.S.) installations. Refer to the Rosemount 3051 Reference Manual for more

instructions. This manual is also available electronically on Emerson.com/

Rosemount.

1.1 Safety messages

Before installing the transmitter, confirm the correct device driver is loaded

on the host systems.

Procedures and instructions in this section may require special precautions

to ensure the safety of the personnel performing the operations.

NOTICE

This guide provides basic guidelines for Rosemount 3051 Transmitters. It

does not provide instructions for configuration, diagnostics, maintenance,

service, troubleshooting, Explosion-Proof, Flame-Proof, or intrinsically safe

(I.S.) installations. Refer to the Rosemount 3051 Reference Manual

Rosemount 3051 Reference Manual for more instructions. This manual is

also available electronically on Emerson.com/Rosemount.

WARNING

Explosions

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in

accordance with the local, national, and international standards, codes,

and practices. Review product certifications for any restrictions

associated with a safe installation.Review the Product certifications

section of the Rosemount 3051 Product Data Sheet for any restrictions

associated with a safe installation.

Before connecting a handheld communicator in an explosive

atmosphere, ensure that the instruments in the loop are installed in

accordance with intrinsically safe or non-incendive field wiring practices.

In an explosion-proof/flameproof installation, do not remove the

transmitter covers when power is applied to the unit.

January 2020 Quick Start Guide

Quick Start Guide 3

WARNING

Process leaks

Process leaks could result in death or serious injury.Process leaks may cause

harm or result in death.Process leaks may cause harm or result in death.

Install and tighten process connectors before applying pressure.

To avoid process leaks, only use the O-ring designed to seal with the

corresponding flange adapter.

Electrical shock

Electrical shock could cause death or serious injury.Electrical shock can result

in death or serious injury.Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a

½–14 NPT thread form. Entries marked “M20” are M20 × 1.5 thread form.

On devices with multiple conduit entries, all entries will have the same

thread form. Only use plugs, adapters, glands, or conduit with a compatible

thread form when closing these entries.

When installing in a hazardous location, use only appropriately listed or Ex

certified plugs, glands, or adapters in cable/conduit entries.

Physical access

Unauthorized personnel may potentially cause significant damage to and/or

misconfiguration of end users’ equipment. This could be intentional or

unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for all

systems used within the facility.

Quick Start Guide January 2020

4 Emerson.com/Rosemount

2 Transmitter installation

2.1 Mount the transmitter

For dimensional drawing information refer to the Dimensional Drawings

section of the Rosemount 3051 Product Data Sheet.

Figure 2-1: Panel Mount Coplanar Flange

5/16 x 1½ panel bolts are customer supplied.

January 2020 Quick Start Guide

Quick Start Guide 5

Figure 2-2: Pipe Mount Coplanar Flange

Figure 2-3: Panel Mount Traditional Flange

Figure 2-4: Pipe Mount Traditional Flange

Quick Start Guide January 2020

6 Emerson.com/Rosemount

Figure 2-5: Panel Mount Rosemount 3051T

Figure 2-6: Pipe Mount Rosemount 3051T

January 2020 Quick Start Guide

Quick Start Guide 7

2.1.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 2-7: Mounting the Transmitter in Liquid Applications

In-line

2.1.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 2-8: Mounting the Transmitter in Gas Applications

In-line

Quick Start Guide January 2020

8 Emerson.com/Rosemount

2.1.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 2-9: Mounting the Transmitter in Steam Applications

In-line

2.1.4 Bolting consideration

If the transmitter installation requires assembly of the process flanges,

manifolds, or flange adapters, follow the assembly guidelines to ensure a

tight seal for optimal performance characteristics of the transmitters.

Use only bolts supplied with the transmitter or sold by Emerson as spare

parts. Figure 2-10 illustrates common transmitter assemblies with the bolt

length required for proper transmitter assembly.

January 2020 Quick Start Guide

Quick Start Guide 9

Figure 2-10: Common Transmitter Assemblies

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 1.75-in. (44 mm)

4 × 2.25-in. (57 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange

adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 2-1. If

bolt material is not shown in Table 2-1, contact a local Emerson

representative for more information.

Carbon steel bolts do not require lubrication, and the stainless steel bolts are

coated with a lubricant to ease installation. However, do not apply additional

lubricant when installing either type of bolt.

Table 2-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial

torque

Final

torque

Carbon Steel (CS)

B7M

300 in-lb 650 in-lb

Stainless Steel (SST)

316

STM

316

B8M

150 in-lb 300 in-lb

Use the following bolt installation procedure:

Quick Start Guide January 2020

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 3051 CF Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051P Bedienungsanleitung

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Micro-Motion 2400S Kurzanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount OCX 8800 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 705 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 5400 Series Bedienungsanleitung

Emerson

Emerson Rosemount Wireless Permasense WT210 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 550PT Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 5408 Bedienungsanleitung

Emerson

Emerson Rosemount 3051HT Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Wireless Series Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 2051HT Bedienungsanleitung

Emerson

Emerson Micro Motion 2500 Kurzanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung