Emerson Rosemount 3051 CF Series Bedienungsanleitung

Quick Start Guide

00825-0100-4774, Rev HB

October 2019

Rosemount™ 3051 Pressure Transmitter

and Rosemount 3051CF Series Flow

Meter

with FOUNDATION™ Fieldbus Protocol

Safety messages

Before installing the transmitter, confirm the correct device driver is loaded on the host systems. See

System readiness.

NOTICE

This guide provides basic guidelines for Rosemount™ 3051 Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof,

Flame-Proof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 Reference Manual for

more instructions. This manual is also available electronically on Emerson.com/Rosemount.

WARNING

Explosions

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the local,

national, and international standards, codes, and practices. Review product certifications for any

restrictions associated with a safe installation.

In an explosion-proof/flameproof installation, do not remove the transmitter covers when power

is applied to the unit.

Process leaks

Process leaks may cause harm or result in death.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange

adapter.

Electrical shock

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Static electricity

Observe safe handling precautions for static-sensitive components.

Conduit/cable entries

Unless marked, the conduit/cable entries in the transmitter housing use a ½–14 NPT thread form.

Entries marked “M20” are M20 × 1.5 thread form. On devices with multiple conduit entries, all entries

will have the same thread form. Only use plugs, adapters, glands, or conduit with a compatible thread

form when closing these entries.

When installing in a hazardous location, use only appropriately listed or Ex certified plugs, glands, or

adapters in cable/conduit entries.

Replacement parts

Replacement equipment or spare parts not approved by Emerson for use as spare parts could reduce

the pressure retaining capabilities of the transmitter and may render the instrument dangerous.

Use only bolts supplied or sold by Emerson as spare parts.

Quick Start Guide October 2019

2 Rosemount 3051

WARNING

Improper assembly

Improper assembly of manifolds to traditional flange can damage sensor module.

For safe assembly of manifold to traditional flange, bolts must break back plane of flange web

(i.e., bolt hole) but must not contact sensor module housing.

Severe changes in the electrical loop may inhibit HART® communication or the ability to reach

alarm values. Therefore, Rosemount cannot absolutely warrant or guarantee that the correct

Failure alarm level (High or Low) can be read by the host system at the time of annunciation.

Physical access

Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end

users’ equipment. This could be intentional or unintentional and needs to be protected against.

Physical security is an important part of any security program and fundamental to protecting your

system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for

all systems used within the facility.

Contents

System readiness......................................................................................................................... 5

Mounting the transmitter.............................................................................................................7

Tagging......................................................................................................................................13

Consider housing rotation..........................................................................................................14

Set the switches......................................................................................................................... 15

Wire, ground, and power up.......................................................................................................17

Configure................................................................................................................................... 20

Zero trim the transmitter........................................................................................................... 28

Product certifications................................................................................................................. 29

October 2019 Quick Start Guide

Quick Start Guide 3

Quick Start Guide October 2019

4 Rosemount 3051

1 System readiness

1.1 Confirm correct device driver

•Verify the correct device driver (DD/DTM™) is loaded on your systems to

ensure proper communications.

•Download the correct device driver at your host vendor download site,

Emerson.com/Rosemount or Fieldbus.org.

Rosemount™ 3051 device revisions and drivers

Table 1-1 provides the information necessary to ensure you have the correct

device driver and documentation for your device.

Table 1-1: Rosemount 3051 FOUNDATION™ Fieldbus Device Revisions and Files

Device

revision(1)

Host Device driver

(DD)(2)

Obtain at Device driver

(DTM)

Manual

document

number

8 All DD4: DD Rev

Fieldbus.org Emerson.com 00809-0100-

4774

All DD5: DD Rev

Fieldbus.org

Emerson AMS™ Device

Manager V

10.5 or

higher: DD

Rev 2

Emerson.com

Emerson AMS Device

Manager V 8

to 10.5: DD

Rev 1

Emerson.com

Emerson 375/475: DD

Rev 2

Easy Upgrade

Utility

7 All DD4: DD Rev

Fieldbus.org Emerson.com 00809-0100-

4774

All DD5: NA N/A

Emerson AMS Device

Manager V

10.5 or

higher: DD

Rev 6

Emerson.com

October 2019 Quick Start Guide

Quick Start Guide 5

Table 1-1: Rosemount 3051 FOUNDATION™ Fieldbus Device Revisions and Files

(continued)

Emerson AMS Device

Manager V 8

to 10.5: DD

Rev 4

Emerson.com

Emerson 375 / 475: DD

Rev 6

Easy Upgrade

Utility

(1) FOUNDATION Fieldbus device revision can be read using a FOUNDATION Fieldbus capable

configuration tool.

(2) Device driver file names use device and DD revision. To access functionality, the correct

device driver must be installed on your control and asset management hosts and on your

configuration tools.

Installation steps

1. Mount the transmitter (Mounting the transmitter).

2. Tag the transmitter (Tagging).

3. Rotate the housing (Consider housing rotation).

4. Set switches and software write lock (Set the switches).

5. Ground, wire, and power up (Wire, ground, and power up).

6. Locate device.

7. Configure (Configure).

8. Zero trim the transmitter (Zero trim the transmitter).

Quick Start Guide October 2019

6 Rosemount 3051

2 Mounting the transmitter

Figure 2-1: Panel and Pipe Mounting

Panel mount(1) Pipe mount

Coplanar flange

Traditional flange

Rosemount™ 3051T

Rosemount 3051H

(1) 5/16 x 1½ panel bolts are customer supplied.

October 2019 Quick Start Guide

Quick Start Guide 7

2.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 2-2: Mounting the Transmitter in Liquid Applications

In-line

2.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 2-3: Mounting the Transmitter in Gas Applications

Inline

Quick Start Guide October 2019

8 Rosemount 3051

2.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 2-4: Mounting the Transmitter in Steam Applications

In-line

2.4 Install bolts

If the transmitter installation requires assembly of the process flanges,

manifolds, or flange adapters, follow the assembly guidelines to ensure a

tight seal for optimal performance characteristics of the transmitters.

Use only bolts supplied with the transmitter or sold by Emerson™ as spare

parts. Figure 2-5 illustrates common transmitter assemblies with the bolt

length required for proper transmitter assembly.

October 2019 Quick Start Guide

Quick Start Guide 9

Figure 2-5: Common Transmitter Assemblies

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 ×1.75-in.

(44 mm) 4 ×1.50-in.

(38 mm)

4 × 1.75-in. (44 mm)

4 × 2.25-in. (57 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange

adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by

viewing the markings on the head of the bolt and referencing Table 2-1. If

bolt material is not shown in Table 2-1, contact a local Emerson

representative for more information.

Carbon steel bolts do not require lubrication, and the stainless steel bolts are

coated with a lubricant to ease installation. However, do not apply additional

lubricant when installing either type of bolt.

Table 2-1: Torque Values for the Flange and Flange Adapter Bolts

Bolt material Head markings Initial

torque

Final

torque

Carbon Steel (CS)

B7M

300 in-lb 650 in-lb

Stainless Steel (SST)

316

STM

316

B8M

150 in-lb 300 in-lb

Use the following bolt installation procedure:

Quick Start Guide October 2019

10 Rosemount 3051

Andere Handbücher für Rosemount 3051 CF Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 1408H Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 56 Bedienungsanleitung

Emerson

Emerson Rosemount 3101 Bedienungsanleitung

Emerson

Emerson Micro Motion 1000 Series Kurzanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson Rosemount 2051HT Bedienungsanleitung

Emerson

Emerson Micro Motion 1600 Bedienungsanleitung

Emerson

Emerson Rosemount 2051HT Bedienungsanleitung

Emerson

Emerson Micro Motion 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson MICRO MOTION 2700 Betriebsanleitung

Emerson

Emerson Rosemount Wireless Permasense WT210 Bedienungsanleitung

Emerson

Emerson Rosemount 550PT Bedienungsanleitung

Emerson

Emerson Rosemount Oxymitter 4000 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 326P Bedienungsanleitung

Emerson

Emerson Rosemount 708 Bedienungsanleitung

Emerson

Emerson Rosemount 2240S Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Rosemount 1066 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung