Emerson Rosemount 1066 Bedienungsanleitung

Quick Start Guide

00825-0100-3166, Rev AA

April 2019

Rosemount™ 1066

Single Channel Transmitter

Safety Information

Emerson designs, manufactures, and tests its products to meet many national and international

standards. Because these instruments are sophisticated technical products, you must properly install,

use, and maintain them to ensure they continue to operate within their normal specifications. The

following instructions must be adhered to and integrated into your safety program when installing,

using, and maintaining Emerson products. Failure to follow the proper instructions may cause any one

of the following situations to occur: loss of life, personal injury, property damage, damage to this

instrument, and warranty invalidation.

•Read all instructions prior to installing, operating, and servicing the product.

•If this Quick Start Guide is not the correct one, call 1 800 999 9307 to request the correct Quick

Start Guide. Save this Quick Start Guide for future reference.

•If you do not understand any of the instructions, contact your Emerson representative for

clarification.

•Follow all warnings, cautions, and instructions marked on and supplied with the product.

•Inform and educate your personnel in the proper installation, operation, and maintenance of the

product.

•Install equipment as specified in the installation instructions of the appropriate Reference Manual

and per applicable local and national codes. Connect all products to the proper electrical and

pressure sources.

•When replacement parts are required, ensure that qualified people use replacement parts

specified by Emerson. Unauthorized parts and procedures can affect the product's performance,

place the safe operation of your process at risk, and VOID YOUR WARRANTY. Look-alike

substitutions may result in fire, electrical hazards, or improper operation.

•Ensure that all equipment doors are closed and protective covers are in place, except when

maintenance is being performed by qualified people, to prevent electrical shock and personal

injury.

WARNING

Risk of electrical shock

Do not open while the circuit is live.

Only clean with a damp cloth.

NOTICE

If a 475 Universal HART® Communicator is used with these transmitters, the software within the 475

may require modification. If a software modification is required, please contact your local Emerson

Service Group or National Response Center at 1-800-654-7768.

Quick Start Guide April 2019

2 Emerson.com/Rosemount

WARNING

Electrostatic ignition hazard

Special conditions for safe use (when installed in hazardous areas)

The plastic enclosure, except the front panel, must only be cleaned with a damp cloth. The surface

resistivity of the non-metallic enclosure materials is greater than one gigaohm. Take care to avoid

electrostatic charge build-up. Do not rub or clean the transmitter with solvents or a dry cloth.

The panel mount gasket has not been tested for type of protection IP66 or Class II and III. Type of

protection IP66 and Class II, III refer to the enclosure only.

Special condition of use of Rosemount™ 1066 C FF/FII5 and 1066 T FF/FII5. For use with simple

apparatus Rosemount 140, 141, 142, 150, 400, 401, 402, 402VP, 403, 403VP, 404, and 410VP

contacting conductivity sensors and Rosemount 222, 225, 226, and 228 toroidal sensors.

Contents

Install.............................................................5

Wire.............................................................12

Navigating the display..................................23

Start up transmitter..................................... 27

Declaration of Conformity............................29

China RoHS table......................................... 31

April 2019 Quick Start Guide

Quick Start Guide 3

Quick Start Guide April 2019

4 Emerson.com/Rosemount

1 Install

1.1 Unpack and inspect

Procedure

1. Inspect the shipping container. If it is damaged, contact the shipper

immediately for instructions.

2. If there is no apparent damage, unpack the container. Be sure all

items shown on the packing list are present. If items are missing,

notify Emerson immediately.

1.2 Mount

Figure 1-1: Panel Mount Front View

April 2019 Quick Start Guide

Quick Start Guide 5

Figure 1-2: Panel Mount Side View

A. 4X mounting brackets and screws provided with instrument

B. Panel supplied by others. Maximum thickness: 0.375 in. (9.52 mm)

C. Panel mount gasket

Figure 1-3: Panel Mount Bottom View

A. Conduit openings

Quick Start Guide April 2019

6 Emerson.com/Rosemount

Figure 1-4: Panel Cut-Out

A. Maximum

Figure 1-5: Wall Mount Front View

A. 2-in. (50.8 mm) pipe supplied by customer

B. 4 cover screws

April 2019 Quick Start Guide

Quick Start Guide 7

Figure 1-6: Wall Mount Side View

Figure 1-7: Pipe Mount Bottom View

A. Front panel

B. 2-in. (50.8 mm) pipe mount bracket

C. 2 sets of U-bolts for 2-in. (50.8 mm) pipe in kit PN 23820-00

Quick Start Guide April 2019

8 Emerson.com/Rosemount

Figure 1-8: Pipe Mount Side View

1.3 General installation information

1. Install the transmitter with a sunshield or out of direct sunlight and

areas with extreme temperatures.

2. Install the system in an area where vibrations and electromagnetic

and radio frequency interference are minimized or absent.

3. Keep the transmittter and sensor wiring at least one foot from high

voltage conductors. Be sure there is easy access to the transmitter

and sample conditioning system.

4. The transmitter is suitable for panel, pipe, or surface mounting.

5. The transmitter case has six ½-in. (12.7 mm) conduit openings. Use

separate conduit openings for the power/output cable, the sensor

cable, and the other sensor cable as needed (pH input for free

chlorine with continuous pH correction).

6. Use weathertight cable glands to keep moisture out of the

transmitter. If using a conduit, plug and seal the connections at the

transmitter housing to prevent moisture from getting inside the

instrument.

7. Install cable gland fittings and plugs as needed to properly seal the

transmitter on all six enclosure openings. The USB port cover must be

fully installed on the front cover to ensure proper transmitter sealing.

April 2019 Quick Start Guide

Quick Start Guide 9

1.4 Prepare conduit openings

There are six conduit openings in all configurations of the transmitter.

Note

Emerson fits four of openings with plugs upon shipment.

Figure 1-9: Conduit openings

A. Front panel/keypad

B. Power leads

C. Alarm relay leads

D. Sensor 1 cable

E. 4-20 mA/HART®/Profibus® leads

F. Sensor 2 cable

G. Spare opening

Note

Always use proper cable gland fittings and plugs for wire and cable

installations.

Conduit openings accept ½-in. (12.7 mm) conduit fittings or PG13.5 cable

glands. To keep the case watertight, block unused openings with Type 4X or

IP66 conduit plugs.

Quick Start Guide April 2019

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 1066

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Micro Motion Bedienungsanleitung

Emerson

Emerson Rosemount 708 Bedienungsanleitung

Emerson

Emerson Rosemount 1208 Bedienungsanleitung

Emerson

Emerson Micro Motion 2400S Bedienungsanleitung

Emerson

Emerson Rosemount 2240S Bedienungsanleitung

Emerson

Emerson Rosemount 2088 Bedienungsanleitung

Emerson

Emerson Rosemount 644R Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 644 Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson PT5N Series Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Micro Motion 9739 MVD Kurzanleitung

Emerson

Emerson MICRO MOTION 2700 Bedienungsanleitung

Emerson

Emerson Rosemount 148 Bedienungsanleitung

Emerson

Emerson Rosemount 5402 Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount 2051CF series Bedienungsanleitung

Emerson

Emerson Rosemount MultiVariable 3051SMV Bedienungsanleitung

Emerson

Emerson Oxymitter 5000 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung