Emerson Rosemount 3051 Series Bedienungsanleitung

Quick Start Guide

00825-0100-4797, Rev FD

February 2019

Rosemount™ 3051 Pressure Transmitter

and Rosemount 3051CF Series Flow

Meter

with PROFIBUS® PA Protocol

NOTICE

This installation guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-Proof,

Flame-Proof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 Reference Manual for

more instruction. This manual is also available electronically on EmersonProcess.com/Rosemount.

WARNING

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate

local, national, and international standards, codes, and practices. Review the approvals section of the

Rosemount 3051 Reference Manual for any restrictions associated with a safe installation.

Do not remove the transmitter cover in explosive atmospheres when the circuit is live.

Process leaks could result in death or serious injury.

To avoid process leaks, only use the O-ring designed to seal with the corresponding flange adapter.

Electrical shock could cause death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Conduit/cable entries

Unless otherwise marked, the conduit/cable entries in the housing enclosure use a ½–14 NPT form.

Only use plugs, adapters, glands, or conduit with a compatible thread form when closing these entries.

Contents

Mount the transmitter................................... 3

Consider housing rotation............................12

Set jumpers and switches.............................13

Connect wiring and power up...................... 14

Basic configuration...................................... 18

Trim the transmitter.................................... 21

Product Certifications.................................. 22

Quick Start Guide February 2019

2 Emerson.com/Rosemount

1 Mount the transmitter

Figure 1-1: Panel Mount Coplanar Flange

5/16 x 1½ panel bolts are customer supplied.

Figure 1-2: Pipe Mount Coplanar Flange

February 2019 Quick Start Guide

Quick Start Guide 3

Figure 1-3: Panel Mount Traditional Flange

Figure 1-4: Pipe Mount Traditional Flange

Figure 1-5: Panel Mount Rosemount™ 3051T

Quick Start Guide February 2019

4 Emerson.com/Rosemount

Figure 1-6: Pipe Mount Rosemount 3051T

1.1 Mount the transmitter in liquid applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so the drain/vent valves are oriented upward.

Figure 1-7: Mounting the Transmitter in Liquid Applications

Coplanar In-line

Flow

1.2 Mount the transmitter in gas applications

Procedure

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 1-8: Mounting the Transmitter in Gas Applications

Coplanar Inline

February 2019 Quick Start Guide

Quick Start Guide 5

Flow

1.3 Mount the transmitter in steam applications

Procedure

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 1-9: Mounting the Transmitter in Steam Applications

Coplanar In-line

Flow

1.4 Mounting options

Coplanar flange

Panel mount(1) Pipe mount

Quick Start Guide February 2019

6 Emerson.com/Rosemount

Traditional flange

Panel mount(2) Pipe mount

Rosemount 3051T

Panel mount(3) Pipe mount

(1) Panel bolts are customer supplied.

(2) Panel bolts are customer supplied.

(3) Panel bolts are customer supplied.

February 2019 Quick Start Guide

Quick Start Guide 7

1.5 Bolting considerations

If the transmitter installation requires assembly of the process flanges,

manifolds, or flange adapters, follow these assembly guidelines to ensure a

tight seal for optimal performance characteristics of the transmitters. Use

only bolts supplied with the transmitter or sold by Emerson as spare parts.

Figure 1-10 illustrates common transmitter assemblies with the bolt length

required for proper transmitter assembly.

Figure 1-10: Common Transmitter Assemblies

4 × 2.88-in. (73 mm)

4 × 1.75-in. (44 mm)

4 ×1.75-in.

(44 mm) 4 ×1.75-in.

(44 mm)

4 × 1.75-in. (44 mm)

4 × 2.25-in. (57 mm)

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange

adapters

Bolts are typically carbon steel (CS) or stainless steel (SST). Confirm the

material by viewing the markings on the head of the bolt and referencing

Table 1-1. If bolt material is not shown in Table 1-1, contact a local Emerson

representative for more information.

Procedure

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Table 1-1 for initial torque value.

Quick Start Guide February 2019

8 Emerson.com/Rosemount

4. Torque the bolts to the final torque value using the same crossing

pattern. See Table 1-1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

Example

Table 1-1: Torque Values for the Coplanar Flange and Flange Adapter

Bolts

Bolt material Head markings Initial

torque

Final

torque

B7M

300 in-lb 650 in-lb

SST

316

STM

316

B8M

150 in-lb 300 in-lb

February 2019 Quick Start Guide

Quick Start Guide 9

1.6 O-rings with flange adapters

WARNING

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. The two flange adapters are distinguished

by unique O-ring grooves. Only use the O-ring that is designed for its specific

flange adapter, as shown below.

Figure 1-11: O-ring Location

Rosemount 3051S/3051/2051

A. Flange adapter

B. O-ring

C. PFTE-based profile (square)

D. Elastomer profile (round)

Whenever the flanges or adapters are removed, visually inspect the O-rings.

Replace them if there are any signs of damage, such as nicks or cuts. If you

replace the O-rings, re-torque the flange bolts and alignment screws after

installation to compensate for seating of the PTFE O-ring.

1.7 Environmental seal for housing

Thread sealing (PFTE) tape or paste on male threads of conduit is required to

provide a water/dust tight conduit seals and meets requirements of NEMA®

Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are

required.

For M20 threads, install conduit plugs to full thread engagement or until

mechanical resistance is met.

1.8 In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located in the neck of the transmitter, behind the housing. The

Quick Start Guide February 2019

10 Emerson.com/Rosemount

Andere Handbücher für Rosemount 3051 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Sender Handbücher

Emerson

Emerson Micro Motion 2400S Kurzanleitung

Emerson

Emerson Rosemount 644h Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 2051HT Bedienungsanleitung

Emerson

Emerson Rosemount 248 Bedienungsanleitung

Emerson

Emerson Rosemount CX1100 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 2051 Bedienungsanleitung

Emerson

Emerson Rosemount 648 Bedienungsanleitung

Emerson

Emerson Rosemount 3144P Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 1151 Bedienungsanleitung

Emerson

Emerson Rosemount 326P Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 4600 Bedienungsanleitung

Emerson

Emerson Rosemount 702 Bedienungsanleitung

Emerson

Emerson Rosemount 2051G Bedienungsanleitung

Emerson

Emerson Rosemount 848T Bedienungsanleitung

Emerson

Emerson MICRO MOTION 2700 Bedienungsanleitung

Emerson

Emerson Rosemount MCL-220 Bedienungsanleitung

Emerson

Emerson MicroMotion FOUNDATION 5700 Bedienungsanleitung

Emerson

Emerson Rosemount 3051 Bedienungsanleitung

Emerson

Emerson Rosemount 3408 Bedienungsanleitung

Emerson

Emerson Rosemount 3051S Series Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung